Transition Networks SISTF10xx-130-LR(T) Install the Fiber Cable, Install the Copper Cable

SISTF10xx-130-LR(T)

Installation -- Continued

CAUTION: Disconnect the SISTF10xx-130-LR(T) from the DC power source BEFORE installing and/or wiring the device.

Install the Fiber Cable

To build the Redundant Ring network, connect the SISTF10xx-130-LR(T) devices using the two fiber ports labeled “4” and “5”. The fiber links can be connected between two adjacent devices using any of the following combinations:

A:Port 4 of one device connected to port 4 of the adjacent device.

B:Port 4 of one device connected to port 5 of the adjacent device.

C:Port 5 of one device connected to port 5 of the adjacent device.

Installation -- Continued

Install the Copper Cable

The AutoCross feature allows either straight-through (MDI) or crossover (MDI- X) copper cable to be used when connecting devices via the RJ-45 port.

1.Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45 connectors installed at both ends.

2.Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the SISTF10xx-130-LR(T).

3.Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the other device (PLC, workstation, etc.).

		C
	100BASE-FX		Switch
port 5	TX	PWR 2
		PWR 1
		FAULT	Industrial
	RX	100M
port 4	TX	MASTER Ring
		RING	Redundant
	RX	100M
		10/100BASE-TX

port 5

port 4

100BASE-FX		Switch
TX	PWR 2
	PWR 1	Industrial
	100M
	FAULT
RX
TX	MASTER Ring
	RING	Redundant
RX	100M
	10/100BASE-TX

B
	100BASE-FX		Switch
	TX	PWR 2
port 5		PWR 1
	RX	100M	Industrial
		FAULT
port 4	TX	MASTER Ring
		RING
	RX		Redundant
		100M
		10/100BASE-TX

RJ-45 ports on the	RJ-45 port
SISTF10xx-130-LR(T)	on the other device
	(PLC, work station, etc.)

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the dip switches. Failure to observe this caution could result in damage to, and failure of, the SISTF10xx-130-LR(T).

A

When connecting the fiber links, make sure the transmit (TX) port on one device is connected to the receive (RX) port on the adjacent device as shown:

Set the Dip Switches

•The dip switches are located on the top panel of the device.

•Use a small flat blade screwdriver or a similar device to set the switches.

NOTE: To activate the updated switch setting, cycle the power to the SISTF10xx-130-LR(T) by turning off the power, then turning it back on.

Switches 1 - 5: Port Alarm

Connect the fiber cable to the SISTF10xx-130-LR(T) as shown.

Connect the fiber cable to the adjacent SISTF10xx-130-LR(T) as shown

The port alarm feature is used to determine faults at the copper or fiber ports.

•Switches 1, 2, and 3 correspond to copper ports 1, 2, and 3, respectively.

•Switches 4 and 5 correspond to fiber ports 4 and 5, respectively.

RX

TX

RX

TX

on: Enables the corresponding port alarm. If the link for that port fails (or if a power supply input fails), the internal relay forms an open circuit and the FAULT LED lights up.

P1

P2

P3

1 2	ON
3

PORT ALARM

NOTE: Calculate the maximum possible current in each power wire and signal wire. Observe all electrical codes for maximum current allowed. If the current goes above the maximum ratings, the wiring would overheat, causing serious damage to the network equipment.

off: Disables the corresponding port alarm. The internal relay forms a closed circuit and the FAULT LED remains off.

P4

P5 RM

4	DIP
5 6

RING MASTER

4 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 5