IBM PRO/100 SP manual Configuration Setup, Packet Protect, Adaptive Link Response

Page 23

Configuration Setup

The Boot Agent software provides configuration options that allow you to customize the behavior of the Boot Agent software. Changing the Boot Agent configuration will usually be required only the first time you add a new network adapter to a client computer within your network. You can configure the Boot Agent within any of the following environments:

vPre-boot environments (before operating system is loaded)

vWindows environments

vDOS environments

Packet Protect

Packet Protect enables you to:

vProtect confidentiality and authenticity of IP traffic on your LAN using Internet Protocol Security (IPSec), including Internet Key Exchange (IKE).

vOffload security tasks to an Intel PRO/100 S Management or Server Adapter to optimize network performance.

Adaptive Link Response

The Adaptive Link Response feature allows the MiniPCI adapter installed in a mobile product to recognize whether or not the network cable is connected to the LAN card. This will avoid the Domain Login error No Domain Server was available to validate your password.

vIf no network link is detected, the operating system will display a two-line login window, and will not fully load the LAN driver.

vIf a network link is detected, the operating system will display a three-line login window, and will fully load the LAN driver.

Part 1: Installation and user’s guide

1-15

Image 23
Contents Intel PRO/100 SP Mobile Combo Adapter Page Contents Iv Intel PRO/100 SP Mobile Combo Adapter User’s Guide Safety Read first Vi Intel PRO/100 SP Mobile Combo Adapter User’s Guide Registering your option Part 1 Installation and user’s guideAbout this book Online user’s guideViii Intel PRO/100 SP Mobile Combo Adapter User’s Guide Attach the network and modem cables Part 1 Installation and user’s guideInstalling Ethernet and modem device drivers System requirementsClick OK on Do you want to install the modem driver? Installing the Ethernet and Modem device drivers in WindowsClick Start→Run Select The Updated Driver Recommended and click NextFor Windows 95 OSR0 or OSR1 Click Do not install a driverClick Other Location Click CancelFor Windows 95 OSR2.1 or OSR2.5 6Intel PRO/100 SP Mobile Combo Adapter User’s Guide Additional setup and configuration Using the modem abroadSetting up the dialing properties Performing an Unattended Install802.1p/802/1Q Tagging Advanced featuresAdvanced adapter features Control Panel, double-clickNetworkAdaptive Transmit Threshold Enable PMEDefault Range 1 Adaptive Technology Adaptive Inter-Frame SpacingPCI Bus Efficiency Locally Administered Address LAACoalesce Buffers Link Speed & DuplexIntel Priority Packet An Overview Smart Power DownReceive Buffers Transmit Control BlocksIntel High Priority Queue Double-clickNetwork in Control Panel How to Join a Vlan From Windows NTWake on LAN Virtual LANProduct Contents Adaptive Link Response Configuration SetupPacket Protect 16Intel PRO/100 SP Mobile Combo Adapter User’s Guide Troubleshooting network adapter Appendix A. TroubleshootingFollowing table describes troubleshooting the modem Troubleshooting modemGeneral Modem Hardware Function Appendix B. Modem functionCommand Description AT command summaryRegister Default Description AT commands reference S-Registers1 S2 AT Escape Character user defined S0 Auto Answer Ring NumberS1 Ring Counter S4 Response Formatting Character user defined S3 Command Line Termination Character user definedS5 Command Line Editing Character user defined S8 Comma Dial Modifier Time S6 Wait Before DialingS7 Connection Completion Time-Out S14 General Bit Mapped Options Status S10 Automatic Disconnect DelayS11 Dtmf Dialing Speed S12 Escape Guard TimeS22 Results Bit Mapped Options Status S21 V.24/General Bit Mapped Options StatusS30 Inactivity Timer S24 Timer to Control Sleep ModeS28 V.34 Modulation Enable/Disable S35 Data Calling Tone S32 Synthetic Ring VolumeS37 Dial Line Rate default S33 Synthetic Ring FrequencyS38 K56flex Downstream Rate RBS Links Rate Hit kbit/s S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S108 Network Codec Type S89 Timer to Control Sleep ModeS90 Read-only Local Phone 16Intel PRO/100 SP Mobile Combo Adapter User’s Guide LAN specifications Appendix C. SpecificationsAdapter specifications 2Intel PRO/100 SP Mobile Combo Adapter User’s Guide Telephone technical support Appendix D. Help and service informationOnline technical support Support 24 hours a day, 7 days a week IBM Warranty for Machines Appendix E. Product warranty and noticesWarranty Statements Warranty Service Extent of WarrantyItems Not Covered by Warranty Appendix E. Product warranty and notices Limitation of Liability Production StatusIBM Warranty for Machines Warranties of ANY Kind Production Status Asia Pacific Part 2 Worldwide Country-Unique TermsFollowing terms apply to all Emea countries EUROPE, Middle EAST, Africa EmeaFollowing terms apply to the country specified Appendix E. Product warranty and notices North America Appendix E. Product warranty and notices IBM TrademarksEuropean Union emission directive Industry Canada Class B emission compliance statementAvis de conformite a la reglementation d’Industrie Canada Deutsche EMV-Direktive electromagnetische VerträglichkeitUnion Europea Normativa EMC Union Européenne Directive Conformité électromagnétiqueUnione Europea Directiva EMC Conformidad électromagnética Appendix E. Product warranty and notices Canadian Department of Communications certification label Appendix E. Product warranty and notices Annex II of the Directive Declaration of ConformityName/Machine Type Intel PRO/100 SP Mobile Combo Adapter 1995/5/ECNetwork Compatibility Declaration New Zealand Compliance Statement22Intel PRO/100 SP Mobile Combo Adapter User’s Guide Appendix F. User notices 2Intel PRO/100 SP Mobile Combo Adapter User’s Guide Page Part Number 06P3814 1P P/N 06P3814