IBM PRO/100 SP manual S42 Auto Rate default 1, range, S43 Auto Mode default 1, range

Page 40

One special value of S38, S38 = 251, is used for back-to-back (factory) testing of V.34 rates, with DSP code running in external memory. Set S38=251 on both originating and answering modems. (This feature is not valid with ramless solution.)

S42 Auto Rate (default 1, range 0-1)

This command is used for testing and debugging only. V.32bis and V.22bis auto rate is disabled. Retrain operation is disabled or enabled in data mode, and fallback is disabled in data mode. In K56flex mode, S42=0 forces connection at the rate specified by S38 (even if the rate cannot be sustained), without fallback to V.34.

0 = auto rate disabled, 1 = enabled.

Range: 0-1

Default: 1

S43 Auto Mode (default 1, range 0-1)

This command is used for testing and debugging only.

V.32bis startup auto mode operation disabled.

0 = auto mode disabled, 1 = enabled.

Range: 0-1

Default: 1

S48 LAPM Error Control and Feature Negotiation (default 7)

S48 = 7 Negotiation enabled

S48 = 128 Negotiation disabled; forces immediate fallback options specified in S36

The following chart lists the S36 and S48 configuration settings necessary to negotiate certain types of connections:

Table 7: S36 and S48 Configuration Settings

 

S48 = 7

S48 = 128

 

 

 

S36 = 0,2

LAPM or hangup

do not use

 

 

 

B-14Intel® PRO/100 SP Mobile Combo Adapter: User’s Guide

Image 40
Contents Intel PRO/100 SP Mobile Combo Adapter Page Contents Iv Intel PRO/100 SP Mobile Combo Adapter User’s Guide Safety Read first Vi Intel PRO/100 SP Mobile Combo Adapter User’s Guide Part 1 Installation and user’s guide About this bookOnline user’s guide Registering your optionViii Intel PRO/100 SP Mobile Combo Adapter User’s Guide Part 1 Installation and user’s guide Installing Ethernet and modem device driversSystem requirements Attach the network and modem cablesInstalling the Ethernet and Modem device drivers in Windows Click OK on Do you want to install the modem driver?Select The Updated Driver Recommended and click Next Click Start→RunClick Do not install a driver For Windows 95 OSR0 or OSR1For Windows 95 OSR2.1 or OSR2.5 Click CancelClick Other Location 6Intel PRO/100 SP Mobile Combo Adapter User’s Guide Using the modem abroad Setting up the dialing propertiesPerforming an Unattended Install Additional setup and configurationAdvanced features Advanced adapter featuresControl Panel, double-clickNetwork 802.1p/802/1Q TaggingEnable PME Default Range 1 Adaptive TechnologyAdaptive Inter-Frame Spacing Adaptive Transmit ThresholdLocally Administered Address LAA Coalesce BuffersLink Speed & Duplex PCI Bus EfficiencySmart Power Down Receive BuffersTransmit Control Blocks Intel Priority Packet An OverviewIntel High Priority Queue How to Join a Vlan From Windows NT Wake on LANVirtual LAN Double-clickNetwork in Control PanelProduct Contents Packet Protect Configuration SetupAdaptive Link Response 16Intel PRO/100 SP Mobile Combo Adapter User’s Guide Appendix A. Troubleshooting Troubleshooting network adapterTroubleshooting modem Following table describes troubleshooting the modemAppendix B. Modem function General Modem Hardware FunctionAT command summary Command DescriptionRegister Default Description AT commands reference S-Registers1 S1 Ring Counter S0 Auto Answer Ring NumberS2 AT Escape Character user defined S5 Command Line Editing Character user defined S3 Command Line Termination Character user definedS4 Response Formatting Character user defined S7 Connection Completion Time-Out S6 Wait Before DialingS8 Comma Dial Modifier Time S10 Automatic Disconnect Delay S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options StatusS21 V.24/General Bit Mapped Options Status S22 Results Bit Mapped Options StatusS28 V.34 Modulation Enable/Disable S24 Timer to Control Sleep ModeS30 Inactivity Timer S32 Synthetic Ring Volume S37 Dial Line Rate defaultS33 Synthetic Ring Frequency S35 Data Calling ToneS38 K56flex Downstream Rate RBS Links Rate Hit kbit/s S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S90 Read-only Local Phone S89 Timer to Control Sleep ModeS108 Network Codec Type 16Intel PRO/100 SP Mobile Combo Adapter User’s Guide Adapter specifications Appendix C. SpecificationsLAN specifications 2Intel PRO/100 SP Mobile Combo Adapter User’s Guide Online technical support Appendix D. Help and service informationTelephone technical support Support 24 hours a day, 7 days a week Warranty Statements Appendix E. Product warranty and noticesIBM Warranty for Machines Items Not Covered by Warranty Extent of WarrantyWarranty Service Appendix E. Product warranty and notices Production Status Limitation of LiabilityIBM Warranty for Machines Warranties of ANY Kind Production Status Part 2 Worldwide Country-Unique Terms Asia PacificEUROPE, Middle EAST, Africa Emea Following terms apply to all Emea countriesFollowing terms apply to the country specified Appendix E. Product warranty and notices North America Appendix E. Product warranty and notices Trademarks IBMIndustry Canada Class B emission compliance statement Avis de conformite a la reglementation d’Industrie CanadaDeutsche EMV-Direktive electromagnetische Verträglichkeit European Union emission directiveUnione Europea Directiva EMC Conformidad électromagnética Union Européenne Directive Conformité électromagnétiqueUnion Europea Normativa EMC Appendix E. Product warranty and notices Canadian Department of Communications certification label Appendix E. Product warranty and notices Declaration of Conformity Name/Machine Type Intel PRO/100 SP Mobile Combo Adapter1995/5/EC Annex II of the DirectiveNew Zealand Compliance Statement Network Compatibility Declaration22Intel PRO/100 SP Mobile Combo Adapter User’s Guide Appendix F. User notices 2Intel PRO/100 SP Mobile Combo Adapter User’s Guide Page Part Number 06P3814 1P P/N 06P3814