Fujitsu MB9B500 Series On-Board Programming via USB, 4 USB Device Sign, 6 USB Programmer Overview

Page 11

3.2 On-Board Programming via USB

First check the hardware setting as introduced by section 2.4.

After connect with PC via USB cable, the EVB can be identified as a USB device.

Figure 3-4: USB Device Sign

Check the COM port for this USB port in the device manager.

Figure 3-5: COM Port in Device Manager

Install the USB programmer: USBDW_V01L03. (It can be downloaded on the web)

Open it, set the parameter as shown in following figure, and select Hex file.

Figure 3-6: USB Programmer Overview

Click Full Operation.

Figure 3-7: Press Reset Button

Image 11

Contents APPLICATION NOTE FUJITSU SEMICONDUCTOR SHANGHAI LIMITEDMB9B500 Series 32-BIT MICROCONTROLLERALL RIGHTS RESERVED 2011-04-21 Revision HistoryDate Version3 FLASH ON-BOARD PROGRAMMING 2 HARDWARE SETTINGREVISION HISTORY 1 INTRODUCTION1.2 MB9B506 Series MCU 1 Introduction1.1 Product Overview 1.3 Board Features AD channel 2 Hardware SettingTable 2-2 Setting for UART On-Board Programming 2.3 Setting for UART On-Board Programming2.4 Setting for USB On-Board Programming 2.2 Jumpers Overview„ Use Keil U-Link ME 2.5 Setting for Debug Tool„ Use IAR J-Link 3.1 On-Board Programming via UART 3 Flash On-Board ProgrammingFigure 3-5 COM Port in Device Manager 3.2 On-Board Programming via USBFigure 3-7 Press Reset Button Figure 3-4 USB Device SignFigure 3-8 Start Programming „ Press reset key on the board. Programming will start4 Sample Code „ Usage 4.1 UART„ Hardware Setting „ FlowchartFigure 4-3 Send UART Data From PC Side Flowchart 4.2 Nand Flash4.3 RTC „ Hardware Setting None „ Flowchart„ Block Diagram 4.4 CAN4.5 USB Function 4.6 USB Host 4.7 LCD & AD & Key Figure 5-1 J-Link Overview Figure 5-2 U-Link Overview 5 Debug Tool and IDEWatch window Main window 5.1 Debug with J-Link in IAR EWARM Workbench„ Run an Existed Project Tool bar Project list Log windowFigure 5-6Rebuild All 2 Select a project eww file3 Click “Project Rebuild All” Figure 5-5 Select a Project„ Setting for Flash Debug Figure 5-11 Flash Load File Path 2 Don’t select “Use macro files” in “DebuggerSetup” tableFigure 5-10 Macro File Disabled Figure 5-12 ICF File for RAM Debug „ Setting for RAM Debug2 Select “Use macro files” in “DebuggerSetup” table Figure 5-13 Macro File Enabled1 Use Flash debug „ How to Make a HEX FileFigure 5-14 Flash Loader File Disabled 3 Don’t use Flash loader fileFigure 5-17 Open a Project 5.2 Debug with U-Link ME in Keil uVision4Tool bar Project list Build output Figure 5-16 Keil IDE OverviewFigure 5-18 Select a Project 2 Select a project uvproj file3 Rebuild all 4 Start debugFigure 5-21 Debug Tool Bar Figure 5-22 ROM Address Setting for Flash DebugFigure 5-23 Don’t use initialization File 3 Check “Update Target before Debugging” checkboxFigure 5-24 Select Update Target Before Debugging 2 Don’t use initialization fileFigure 5-26 Select Initialization File 1 Set ROM address in Code SRAM area. 0x1fff8000-0x1fffffff2 Set initialization file path. ..\DebugRAM.ini Figure 5-25 Set RAM Address for RAM DebugFigure 5-28 HEX File Generation in Keil IDE Figure 5-27 Select Update Target Before Debugging„ Sample code 6 Materials Download„ Software „ Document