Fujitsu MB9B500 Series Debug with J-Link in IAR EWARM Workbench, Run an Existed Project

Page 22

5.1 Debug with J-Link in IAR EWARM Workbench

5.1 Debug with J-Link in IAR EWARM Workbench

The sample code can be debugged in IAR EWARM Workbench with J-Link. The following figure shows basic debug window.

Tool bar

Project list

Log window

Figure 5-3: IAR IDE Overview

Run an Existed Project

1)Open a project by clicking “File Open Workspace”

Figure 5-4: Open a Project

Watch window

Main window

22

Image 22

Contents 32-BIT MICROCONTROLLER FUJITSU SEMICONDUCTOR SHANGHAI LIMITEDMB9B500 Series APPLICATION NOTEALL RIGHTS RESERVED Version Revision HistoryDate 2011-04-211 INTRODUCTION 2 HARDWARE SETTINGREVISION HISTORY 3 FLASH ON-BOARD PROGRAMMING1.1 Product Overview 1 Introduction1.2 MB9B506 Series MCU 1.3 Board Features 2 Hardware Setting AD channel2.2 Jumpers Overview 2.3 Setting for UART On-Board Programming2.4 Setting for USB On-Board Programming Table 2-2 Setting for UART On-Board Programming„ Use IAR J-Link 2.5 Setting for Debug Tool„ Use Keil U-Link ME 3 Flash On-Board Programming 3.1 On-Board Programming via UARTFigure 3-4 USB Device Sign 3.2 On-Board Programming via USBFigure 3-7 Press Reset Button Figure 3-5 COM Port in Device Manager„ Press reset key on the board. Programming will start Figure 3-8 Start Programming4 Sample Code „ Flowchart 4.1 UART„ Hardware Setting „ UsageFigure 4-3 Send UART Data From PC Side „ Hardware Setting None „ Flowchart 4.2 Nand Flash4.3 RTC Flowchart4.4 CAN „ Block Diagram4.5 USB Function 4.6 USB Host 4.7 LCD & AD & Key 5 Debug Tool and IDE Figure 5-1 J-Link Overview Figure 5-2 U-Link OverviewTool bar Project list Log window 5.1 Debug with J-Link in IAR EWARM Workbench„ Run an Existed Project Watch window Main windowFigure 5-5 Select a Project 2 Select a project eww file3 Click “Project Rebuild All” Figure 5-6Rebuild All„ Setting for Flash Debug Figure 5-10 Macro File Disabled 2 Don’t select “Use macro files” in “DebuggerSetup” tableFigure 5-11 Flash Load File Path Figure 5-13 Macro File Enabled „ Setting for RAM Debug2 Select “Use macro files” in “DebuggerSetup” table Figure 5-12 ICF File for RAM Debug3 Don’t use Flash loader file „ How to Make a HEX FileFigure 5-14 Flash Loader File Disabled 1 Use Flash debugFigure 5-16 Keil IDE Overview 5.2 Debug with U-Link ME in Keil uVision4Tool bar Project list Build output Figure 5-17 Open a Project4 Start debug 2 Select a project uvproj file3 Rebuild all Figure 5-18 Select a ProjectFigure 5-22 ROM Address Setting for Flash Debug Figure 5-21 Debug Tool Bar2 Don’t use initialization file 3 Check “Update Target before Debugging” checkboxFigure 5-24 Select Update Target Before Debugging Figure 5-23 Don’t use initialization FileFigure 5-25 Set RAM Address for RAM Debug 1 Set ROM address in Code SRAM area. 0x1fff8000-0x1fffffff2 Set initialization file path. ..\DebugRAM.ini Figure 5-26 Select Initialization FileFigure 5-27 Select Update Target Before Debugging Figure 5-28 HEX File Generation in Keil IDE„ Document 6 Materials Download„ Software „ Sample code