IBM 09-0572-000 To change the software option settings, follow these steps, Type at the prompt

Page 37

4-6 CHAPTER 4: STANDARD INSTALLATION AND CONFIGURATION

Table 4-2 Initial 3Com and IBM Mode Option Settings (continued)

Option

3Com Default Setting

IBM Default Setting

 

 

 

Memory Mode

16 bit

16 bit

I/O Mode

16 bit

16 bit

IRQ Driver Type

Edge Triggered

 

AutoSwitch

Disabled

 

Boot PROM

Disabled

 

Zero Wait State

Enabled

 

 

 

 

To change the software option settings, follow these steps:

1Make sure the 3C619C adapter has been properly installed in your PC (refer to Chapter 2 for instructions).

2Boot your PC under DOS, version 3.2 or later.

When you configure adapters, memory conflicts may occur. To help prevent this, follow these rules:

a Do not load network drivers.

b Be aware that terminate and stay resident programs (TSRs) may cause memory conflicts.

cIf you are using a memory management utility, you must inform it of the address ranges used by the adapter. For example, add an exclude parameter to the EMM386 device statement in the CONFIG.SYS file such as:

DEVICE=C:\EMM386.EXE NOEMS X=D800-DBFF

3Place the TokenDisk diskette in a floppy drive on your PC and make that drive the active drive. For example, type:

A:[Enter]

4Type at the prompt:

INSTALL [Enter]

5When the AutoLink Information screen appears, press [Enter].

6From the main menu, select Configuration/Diagnostic/ Troubleshooting.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Member of the TokenLink III product family ISA Adapter User GuideLifetime Warranty Asia 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Installing the Network Driver for Windows Troubleshooting Using the Configuration and Diagnostic Program Page Figures Tables 3Com Mode versus IBM ModeAbout this Guide How to Use This GuideIntroduction Conventions InstallIntroduction TokenLink III 16/4 ISA Token Ring Adapter FeaturesAutoLink Installation Installation and Configuration OptionsAdapter Installation and Configuration Standard Installation and Configuration TroubleshootingWindows Installation and Configuration Transcend PC Link SmartAgent SoftwareMoney-Back Guarantee Adapter Installing the 3C619C3C619C Adapter Installation PC Requirements Inspecting the Adapter Taking Safety PrecautionsCheck the adapter for any visible signs of damage Installing the AdapterRemoving the Backplate Shielded twisted-pair STP cable DB-9 Connecting to the NetworkRJ-45 Locate the DB-9 connector on the shielded twisted-pair cable Connecting to Shielded Twisted-pair STP CableConnecting to Unshielded Twisted-pair UTP Cable Feature for NET Ware Using the Auto LinkAutoLink Options AutoLink RequirementsAvoiding Memory Manager Conflicts Make a backup copy of the CONFIG.SYS file. TypeFollow these steps to use the AutoLink feature Using the AutoLink FeatureType at the prompt Configuration Standard InstallationAuto Configuring the 3C619C Adapter in an ISA PC Configuration RequirementsI N N U IRQ = 2,3,6, or IBM Changing Software Option SettingsTo change the software option settings, follow these steps Adapter Configuration Screen Video Conflicts with BIOS/MMIO and Shared RAM Addresses Changing Settings for Multiple AdaptersChanging Software Option Settings Drivers Installing NetworkDEC PATHWORKS Installing the Novell NetWare DriverMain Menu with Network Drivers Option Selected Updating the PC Startup Files Installing the Server Driver for NetWare Installing the OS/2 Network Driver for NetWareNetWare Systems with Multiple Adapters Installing the Ndis 2.01 Driver Build a PROTOCOL.INI file in the Lanman subdirectory Ndis Systems with Multiple Adapters IBM modeSample PROTOCOL.INI File Updating the Current Ndis Driver Using IBM DriversObtaining IBM Network Drivers Before Using RPL Using Remote Program Load RPLEnabling RPL 3TOKDIAG Enter Installing the Network Driver for Windows NT Installing the NetworkDriver for Windows Click the Continue buttonInstalling the Network Driver for Windows \WIN95 Adapter LEDs TroubleshootingUsing the TokenDisk Diskette Diagnostic Program Depicts how to use the TokenDisk diskette diagnostic program Group 1 Diagnostics Diagnostic Test TypesDiagnostic Test Types Running the Diagnostic Tests Group 2 DiagnosticTest Menu File Options Changing the Test SetupAdapter Statistics and Information When Tests FailAdapter Statistics Adapter Information When Tests FailMmio Register Write/Read Test Failure Boot Prom Test FailureAIP Checksum Test Failure Shared RAM Boundary/Domain Test FailureShared RAM Write/Read Test Failure Timer Test FailureOpen Adapter for Ring Operation Test Failure Ring Operations Test FailureClose Adapter Test Failure Troubleshooting TipsAdapter Wrap Test Failure Group Inspect all cables and connectionsRefer to Appendix B, Specifications Additional Information Error MessagesOn-line Information Technical SupportFigure A-1 Menu Hierarchy Using Configuration Diagnostic ProgramSpeed Keys Using the KeyboardChoosing a Menu Item Using the MouseHelp Using the File OptionsLoad loads a file from a selected directory Exiting the Program Using the Command LineDOS prompt such as A\ type Cabling SpecificationsPin Assignments Cabling Pin Assignments Configuration OptionsFigure B-1 DB-9 Connector Pin Assignments Configuration Options Configuration ModeBase Address Ring SpeedShared RAM Page Size and Address Range BIOS/MMIO Address LocationKB / CE000-CFFFF Interrupt Request LevelOther Configuration Options Messages Error MessagesAppendix C Error Messages Messages C-3 Appendix C Error Messages Messages C-5 3Com Bulletin Board Service On-line Technical ServicesTechnical Support World Wide Web Site 3ComFacts Automated Fax ServiceAsk3Com on CompuServe To use Ask3Com Log on to CompuServeDetails about recent configuration changes, if applicable Support from Your Network SupplierTo obtain an RMA number, call or fax Returning Products for RepairDual access unit Driver Controlled access unit ConfigurationGlossary Industry Standard Architecture Multistation access unitLobe Token ring Protocol layersTSR Numerics IndexNdis View A-3 RPL Limited Warranty FCC Class a Verification Statement

09-0572-000 specifications

The IBM 09-0572-000 is a notable component within IBM's broad range of technology solutions, particularly recognized for its integration in enterprise-level systems. This model is primarily distinguished as a power supply unit designed for IBM's well-established line of servers and storage solutions.

One of the key features of the IBM 09-0572-000 is its reliability under heavy workloads. This power supply is engineered to provide a stable power source, ensuring that systems remain operational during critical processes. It boasts robust protection mechanisms, including overvoltage, undervoltage, and overcurrent protection. These features are essential for safeguarding sensitive components in server environments, where power fluctuations could lead to data loss or hardware failure.

Moreover, the IBM 09-0572-000 supports hot-swapping capabilities, allowing IT administrators to replace the power supply without shutting down the system. This feature significantly enhances system availability and reduces downtime, which is crucial for businesses that rely on 24/7 operations.

In terms of performance, the power supply is designed to meet high-efficiency standards, with many models featuring an energy efficiency rating that complies with the 80 PLUS certification. This designation indicates that the power supply operates efficiently under various loads, translating into lower operational costs and reduced energy consumption for businesses.

The IBM 09-0572-000 is also compatible with multiple server configurations, showcasing its versatility within various IBM enterprise environments. This adaptability makes it an ideal choice not just for current models but also for legacy systems, highlighting its longevity in the tech lifecycle.

With a compact design, this power supply enables optimal space utilization within server racks. It exhibits a well-thought-out construction providing excellent thermal management, which is vital in preventing overheating in densely packed data centers.

Ultimately, the IBM 09-0572-000 epitomizes the combination of reliability, efficiency, and versatility that IBM products are known for. Its advanced protective features, compatibility with a range of systems, and innovative design make it a critical component for ensuring optimal performance and uptime in enterprise IT environments. Whether for small businesses or large-scale operations, the 09-0572-000 continues to be a staple in maintaining the heart of robust IT infrastructures.
Top Page Image Contents