IBM 8183 manual Removing and replacing a CD-ROM, CD-RW, or DVD optical drive

Page 32

Removing and replacing a CD-ROM, CD-RW, or DVD optical drive

1.Open the cover. See “Opening the cover” on page 10.

2.Rotate the drive bay assembly upward to gain access to the cable connections. See “Accessing system board components and drives” on page 12 and “Locating components” on page 11.

3.Disconnect the signal and power cables from the drive.

Note: Blue straps are provided to help when disconnecting cables.

4.Slide the lock1to the unlocked position.

5.Open the door at the front of the drive and slide it out the front of the computer.

6.Install the new drive into the bay.

7.Slide the lock 1to the locked position and close the door at the front of the drive.

8.If you are replacing an existing drive, place the master/slave jumper on the drive in the same position as on the drive being replaced. If you are installing an additional drive, place the master/slave jumper on the drive so that it is a slave. Also refer to any instructions that come with the drive.

9.To connect the drive, go to “Connecting an IDE drive” on page 21.

What to do next:

vTo work with another option, go to the appropriate section.

vTo complete the installation, go to “Closing the cover and connecting the cables” on page 25.

18User Guide

Image 32

Contents User Guide Types 8183, 8184, 8320 Types 8417, 8418, 8419 Page User Guide Types 8183, 8184, 8320 Types 8417, 8418, 8419 Page Contents Iv User Guide Important safety information Conditions that require immediate actionPower cords and power adapters General safety guidelinesService Batteries Extension cords and related devicesPlugs and outlets Heat and product ventilation CD and DVD drive safetyAdditional safety information To connect To disconnect Lithium battery notice Modem safety informationLaser compliance statement Xii User Guide Overview Information resourcesFeatures System summaryExpansion Available options Specifications EnvironmentSupported operating positions Handling static-sensitive devices Installing optionsInstalling external options Cover keylock some models Locating connectors on the rear of your computer Obtaining device driversOpening the cover Locating components Accessing system board components and drives Identifying parts on the system board Installing memory Installing PCI adapters Installing internal drives What to do nextSerial ATA IDE hard disk drive Removing and replacing a CD-ROM, CD-RW, or DVD optical drive Removing and replacing a hard disk drive Connecting a serial ATA hard disk drive Removing and replacing a diskette driveConnecting an IDE drive Installing security featuresIdentifying security locks Integrated security cableInstalling options Cover lock Password protectionRope clip Erasing a lost or forgotten password clearing Cmos Closing the cover and connecting the cablesUser Guide Viewing and changing settings Using the IBM Setup UtilityStarting the IBM Setup Utility program Exiting from the IBM Setup Utility program Using passwordsUser password Administrator passwordUsing Security Profile by Device Using IDE Drives SetupAdvanced settings Selecting a startup deviceSelecting a temporary startup device Changing the startup device sequenceAppendix A. Replacing customer replaceable units CRU CRU list Removing and replacing the power supply assembly User Guide Appendix A. Replacing customer replaceable units CRU Removing and replacing the system board assembly Disconnect all other cables connected to the system board Removing the microprocessor Appendix A. Replacing customer replaceable units CRU Replacing the microprocessor Removing and replacing the battery Removing and replacing the speaker Removing and replacing the power button and LED assembly Speaker, fan, power button and LED assemblyRemoving and replacing the fan assembly Appendix A. Replacing customer replaceable units CRU Completing the installation Updating flashing Bios from your operating system Appendix B. Updating POST/BIOSUpdating flashing Bios from a diskette Recovering from a POST/BIOS update failure Cleaning a mouse with a ball Appendix C. Cleaning the mouseCleaning an optical mouse User Guide Appendix D. Manual modem commands Basic AT commandsLow speaker volume Extended AT commands Enable RTS/CTS hardware flow controlMNP/V.42/V.42bis/V.44 commands +MS=?Fax Class 1 commands Fax Class 2 commandsVoice commands Appendix D. Manual modem commands User Guide Appendix E. Notices Trademarks IBMIndex Special characters CRUPOST/BIOS Page Part Number 13R9208

Related manuals

Manual 76 pages 20.24 Kb