Fujitsu MAX3073FC, MAX3036FC, MAX3147FC manual Dismounting Drives

Page 78

Installation

5.5Dismounting Drives

Since the method and procedure for dismounting the disk drive for replacement of the drive, etc. depends on the locker structure of the system, etc., the work procedure must be determined in consideration of the requirements specific to the system. This section describes the general procedure and notes on dismounting the drive.

Damage

1.When dismounting the drive which is mounted on the system while power is supplied to it.

•The drive to be dismounted must be disconnected from the loop. Dismounting the drive which is not disconnected from the loop may cause an unexpected error.

•If the drive is not disconnected from the loop, issue an LPB to the drive from the initiator in a primitive sequence of the order set.

•It is recommended to stop the spindle motor prior to this loop separation operation. The spindle motor can be stopped by a START/STOP command. It takes about 30 seconds for the spindle motor to stop completely.

•Then, dismount the drive using the drive mounting/dismounting mechanism, etc. of the system. If the drive is dismounted while the spindle motor is running, special care is required to avoid excessive vibration or shock to the drive. It is recommended to stop the operation once the SCA connector breaks off contact and wait until the spindle motor stops (about 30 seconds) before dismount the drive.

•When storing or transporting the drive, put it in an antistatic case (Fcell). (Shown in Section 5.1).

2.When dismounting the drive which is mounted on the system while power is not supplied to it.

•Do not move the drive until the drive stops completely (about 30 seconds if the spindle motor was stopped by a START/STOP UNIT command, and about 30 seconds after powering-off when the power was simply turned off).

•Then, dismount the drive using the drive mounting/dismounting mechanism, etc. of the system.

•When storing or transporting the drive, put it in an antistatic case (Fcell). (Shown in Section 5.1).

5.6Spare Disk Drive

See Subsection 2.1.1, “Model name and order number,” to order a disk drive for replacement or as a spare

5-16

C141-E234

Page 77 Page 79
Image 78
Page 77 Page 79
Contents C141-E234-01EN For Safe Operation C141-E234 This page is intentionally left blank Revision Record Fibre Channel Arbitrated Loop FC-AL Fibre Channel Physical and Signaling Interface FC-PHFibre Channel Physical and Signaling INTERFACE-2 FC-PH-2 Fibre Channel Protocol for Scsi SCSI-FCPPreface Overview of ManualPreface Conventions for Alert MessagesC141-E234 Iii This page is intentionally left blank Important Alert Items Important Alert MessagesImportant Alert Items C141-E234 Vii This page is intentionally left blank Manual Organization Product Maintenance ManualSpecifications Fibre ChannelThis page is intentionally left blank Contents Installation ContentsAppendix a Figures Tables This page is intentionally left blank Standard Features Hardware Structure System Configuration Standard FeaturesGeneral Description Standard Features General Description Hardware Structure FC model drives outer viewGeneral Description System Configuration Example of FC-AL system configurationThis page is intentionally left blank Hardware Specifications Hardware Specifications Model name and order numberModel names and order numbers Specifications Function specificationsHardware Specifications Environmental specifications Environmental/power requirementsError rate ReliabilityMtbf = Hardware Specifications This page is intentionally left blank Cylinder configuration Data Space Logical Data Block Addressing Defect ManagementData Space Data Format SA0Data Space Alternate spare area Spare area in cellTrack format Track skew/head skew Sector formatData Space Format capacity Logical Data Block Addressing Defect Management Defect list Alternate block allocationAlternate block allocation by Format Unit command Defect ManagementAlternate block allocation by Reassign Blocks command Write Write Extend Write Write Extended Format Unit Installation Requirements Mounting Requirements External dimensionsInstallation Requirements DimensionsMounting Requirements Mounting orientationsMounting frame structure Limitation of side-mounting Surface temperature check point HDCMPU Service clearance area MAX3147FC MAX3073FC MAX3036FC Connector location Connection RequirementsInterface connector 10 SCA2 type connectorInstallation Installation Mode settings SettingSetting Loop ID setting Motor start modeMounting Drives Mounting procedures C141-E234 Checking connection Checking the HDD connection a Checking the HDD connection B Formatting Installation Setting parameters Awre ArreArre Awre PER Disc XffffXxxx Port Discovery Dismounting Drives Diagnostics Self-diagnostics Self-diagnostic functionsDiagnostics and Maintenance Diagnostics Test programs Maintenance Information Maintenance Information PrecautionsMaintenance requirements Maintenance levels Revision numbers Revision label exampleTools and test equipment TestsTest flowchart Operation Check Initial seek operation check Diagnostic testOperation Check Operation testTroubleshooting with disk drive replacement in the field Troubleshooting Procedures System-level field troubleshootingTroubleshooting at the repair site Disk drive troubleshootingTroubleshooting Procedures Troubleshooting with parts replacement in the factoryFinding possibly faulty parts This page is intentionally left blank Error Analysis Information Collection Sense Data Analysis Error Analysis Information Collection Sense dataLSB Error AnalysisILI SksvSense Data Analysis Definition of sense dataSense data 1-1x-xx, 3-1x-xx and E-1D-00 Disk read error Sense data 3-0C-03, 4-40-xx, and 4-C4-xxAppendix a Connector Signal Allocation Interface FC-SCA Connector Signal AllocationConnector Signal Allocation Glossary Glossary Target TargAcronyms and Abbreviations Acronyms and Abbreviations OEMBcrc ECCMtbf Mttr Mode SELECT/MODE SelectIndex PADC141-E234 IN-3 This page is intentionally left blank Comment Form This page is intentionally left blank
Related manuals
Manual 1 pages 10.6 Kb

MAX3147FC, MAX3036FC, MAX3073FC specifications

The Fujitsu MAX3036FC, MAX3073FC, and MAX3147FC are advanced integrated circuits that cater to a variety of high-performance applications, predominantly in the realm of communications and data transmission. Each model comes laden with unique features that help in addressing specific requirements in modern electronic systems.

The MAX3036FC, for instance, stands out due to its robust signal processing capabilities. It is particularly optimized for high-speed data communications, making it an excellent choice for applications that demand minimal latency and high data integrity. This featured IC operates within a wide voltage range, ensuring versatility in different circuit environments. It also adopts technology enabling low power consumption, an essential attribute in battery-operated devices.

In contrast, the MAX3073FC brings a distinct set of features suitable for more specialized applications. Its architecture supports a comprehensive serial data communication framework, making it ideal for designs that utilize various communication protocols, including those in industrial automation and automotive systems. The MAX3073FC supports advanced error correction mechanisms which enhance reliability, ensuring more accurate data transmission even over longer distances.

The MAX3147FC, on the other hand, focuses on integrating advanced timing and synchronization technologies. This model is particularly significant in applications that require precise timing signals, such as in telecommunications infrastructure and high-frequency trading systems. The MAX3147FC features integrated oscillators and buffers, streamlining the design process and reducing component count. Additionally, it boasts immunity to electromagnetic interference, a critical factor in maintaining signal integrity in noisy environments.

Common to all three models is Fujitsu's commitment to use cutting-edge manufacturing processes. This ensures the devices are compact, enhancing their suitability for modern designs where space is constrained. The ICs are also designed to handle varying temperature ranges, making them resilient for use in diverse environments.

Each IC is supported by comprehensive documentation and development tools that aid engineers in the rapid prototyping and deployment of their designs. The integration of these advanced features and technologies not only simplifies the design process but also accelerates time-to-market for new products. Whether addressing the demands of communication systems, industrial controls, or consumer electronics, the MAX3036FC, MAX3073FC, and MAX3147FC from Fujitsu represent exceptional flexibility and performance in the landscape of integrated circuit technology.
Top Page Image Contents