Contents of the Setup Mode
This section describes the contents of the setup mode.
No | Item | Description | Selectable | Default | |
parameters | |||||
|
|
|
| ||
|
|
|
|
| |
|
| Specifies the double feed detection. Double |
|
| |
1 | Double feed check | feed is detected by checking the document | No/Yes | No | |
|
| length and/or paper thickness.** |
|
| |
|
|
|
|
| |
| Length check | Specifies the document length to enable | Tolerance: |
| |
2 | double feed detection sets the document | No | |||
=No/10/15/20 mm | No/10/15/20mm | ||||
| length. |
| |||
|
|
|
| ||
|
|
|
|
| |
|
| Scanner automatically sets the | Document: |
| |
|
| No |
| ||
|
| recommended reading parameters. 3 sets |
| ||
3 | IPC | 1: Sharpen | No | ||
of parameters are available when | |||||
|
| not installed. | 2: Darken Character |
| |
|
| 3: Copy Quality |
| ||
|
|
|
| ||
|
|
|
|
| |
4 | Resetting of | Resets the abrasion counter. | |||
abrasion counter | |||||
|
|
|
| ||
|
|
|
|
| |
| Pick start time | Specifies the time from document Insertion | Time: |
| |
5 | to the start of picking. User can select the | 1.0 sec | |||
setting | 0.2 to 29.8 sec | ||||
| most comfortable Pick start time for the job. |
| |||
|
|
|
| ||
|
|
|
|
| |
|
| Specifies the time the scanner waits for the | Time: |
| |
6 | next document insertion after the last | 27 values from | 30 sec | ||
|
| document was scanned. | 1 to 1999 sec |
| |
|
|
|
|
| |
|
| Specifies the horizontal and vertical offset | Offset: | Offset: | |
7 | ADF offset setting* | H: 0 mm | |||
of the image when using the ADF. | |||||
|
| V: 0 mm | |||
|
|
| |||
|
|
|
|
| |
| Flatbed offset | Horizontal and vertical offset of the FB | Offset: | Offset: | |
8 | H: 0 mm | ||||
setting* | image is specified. | ||||
| V: 0 mm | ||||
|
|
| |||
|
|
|
|
| |
9 | Option (IPC/Imprinter) | Displays the type | |||
status display | option. "IPC PRT" is displayed when the | ||||
|
|
| |||
|
|
|
| ||
|
|
|
|
| |
|
| The SCSI ID is selectable. Note that the | SCSI ID: |
| |
10 | SCSI ID setting | new setting is made valid after power is | 5 | ||
0/1/2/3/4/5/6/7 | |||||
|
| turned off and on again. |
| ||
|
|
|
| ||
|
|
|
|
| |
11 | SCSI terminator | Switches the SCSI terminator On/Off. | On/Off | On | |
| setting |
|
|
| |
|
|
|
|
| |
12 | Low Power Mode | Changes the default setting of the duration | 5 min. | 15 min. | |
setting | for power save. | to 60 min. | |||
|
| ||||
|
|
|
|
|