IBM SBC-658 manual Setup keys, These keys helps you navigate in Setup

Page 56

Setup keys

These keys helps you navigate in Setup:

Up arrow	Move to previous item

Down arrow	Move to next item

Left arrow	Move to the item in the left hand

Right arrow	Move to the item in the right hand

Esc	Main Menu: Quit and not save changes into
	CMOS RAM
	Other pages: Exit current page and return to
	Main Menu

PgDn/+	Increase the numeric value or make
	changes

PgDn/-	Decrease the numeric value or make
	changes

F1	General help, only for Status Page Setup
	Menu and Option Page Setup Menu

F2	Change color from total 16 colors. F2 to
	select color forward, Shift-F2 to select color
	backward

F3	Calendar, only for Status Page Setup Menu

F4	Reserved

F5	Restore the previous CMOS value from
	CMOS, only for Option Page Setup Menu

F6	Load the default CMOS RAM value from
	BIOS default table, only for Option Page
	Setup Menu

F7	Load the default

F8	Reserved

F9	Reserved

F10	Save all the CMOS changes, only for Main
	Menu

Chapter 3 Award BIOS Setup 47

Image 56

Contents SBC-658 Copyright Notice Message to the Customer Product Warranty Packing list T i c e N t e n t s Award Bios Setup Ethernet Software configuration General Information Introduction Highly integrated SBCFeatures Specifications Standard SBC functionsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Jumpers and connectors CN1 Locating jumpers J3 J4Locating connectors CN11 CN15CN12 CN10Setting jumpers CPU installing and upgrading Install a CPU in the FC-370 socketPage Installing Sdram DIMMs Memory Installation ProceduresSystem Memory Supplementary information about DimmDOC address select SW1 S5 ~ S6 CPU frequency ratio selectLCD clock signal & driving voltage select J1 COM2 RS-232/422/485 select J2, J3 Clear Cmos J4 Power connectors P8 & P9 PWR1 USB connector CN1 Display connectors CN8, CN2 CN2 CN8Display connector CN8 VGALCD display connector CN2 Keyboard and PS/2 mouse connector CN3, CN15 CN3KB Data MS Data GND Parallel port connector CN4 Parallel port connector table CN4 Parallel port IRQSerial ports CN11, CN5 COM2 RS-232/422/485 serial ports CN5IrDA connector CN6, Pin 1~5 Reset switch CN6, Pin6 External/internal Speaker CN6, Pin ~ 1 For external speaker connectionHard drive LED CN6, Pin 13 CPU fan power connector CN7 100Base-T Ethernet connector CN9 IDE hard drive connector CN10 CN10IDE hard drive connector CN10 Floppy drive connector CN12 CN12Connecting the floppy drive Floppy Drive Connector CN12 Floppy drive connector CN12 Pin SignalDiskOnChip socket U10 DiskOnChip DOC 2000 Installation Award Bios Setup Starting setup To Enter Setup Before Boot Press DEL KEYSetup keys These keys helps you navigate in SetupCase of Problems Getting helpMain setup Menu BiosPage Standard Cmos setup Hard Disks Award Bios Setup LCD & CRT Halt On Page Bios features setup Virus Warning Shadow Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Delayed Transaction Power management setup Power Management Determines the manner in which the monitor is blanked VGA Active Monitor Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Flat Panel/CRT Controller Display Drivers and Utilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsDriver Installation Page Place the Supporting CD-ROMin your CD-ROM drive Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Watchdog Timer Watchdog Timer Each Page Appendix a Watchdog Timer SelectDevice8 //Set Register F2 Select Device 8 SelectDevice8 //Set Register F3 Page Appendix a Watchdog Timer Installing PC/104 Modules PCM-3660 PC/104 module dimenstions inches ±5% Appendix B Installing PC/104 Modules