IBM SBC-658 manual Award Bios Setup

Page 8

Parallel port connector table (CN4)

30

Serial ports (CN11, CN5)

31

IrDA connector (CN6, Pin 1~5)

32

Reset switch (CN6, Pin 6,7)

33

External / internal speaker (CN6, Pin 8~11)

34

Hard drive LED (CN6, Pin 13, 14)

35

CPU fan power connector (CN7)

36

100Base-Tx Ethernet connector (CN9)

37

IDE hard drive connector (CN10)

38

IDE hard drive connector (CN10)

39

Floppy drive connector (CN12)

40

Connecting the floppy drive

41

Floppy drive connector (CN12)

42

DiskOnChip socket (U10)

43

DiskOnChip (DOC) 2000 Installation

44

Chapter 3: Award BIOS Setup

4 5

Starting setup

46

Setup keys

47

Getting help

48

In case of problem

48

Main setup menu

49

Standard CMOS setup

51

BIOS features setup

57

CHIPSET features setup

60

Power management setup

60

PNP/PCI congfiguration setup

69

Load BIOS defaults/Load setup defaults

71

Integrated peripherals setup

72

Supervisor/User password setting

75

IDE HDD auto detection

77

Save & exit setup

78

Image 8
Contents SBC-658 Copyright Notice Message to the Customer Product Warranty Packing list T i c e N t e n t s Award Bios Setup Ethernet Software configuration General Information Introduction Highly integrated SBCFeatures Specifications Standard SBC functionsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Jumpers and connectors CN1 Locating jumpers J3 J4Locating connectors CN11 CN15CN12 CN10Setting jumpers CPU installing and upgrading Install a CPU in the FC-370 socketPage Installing Sdram DIMMs Memory Installation ProceduresSystem Memory Supplementary information about DimmDOC address select SW1 S5 ~ S6 CPU frequency ratio selectLCD clock signal & driving voltage select J1 COM2 RS-232/422/485 select J2, J3 Clear Cmos J4 Power connectors P8 & P9 PWR1 USB connector CN1 Display connectors CN8, CN2 CN2 CN8Display connector CN8 VGALCD display connector CN2 Keyboard and PS/2 mouse connector CN3, CN15 CN3KB Data MS Data GND Parallel port connector CN4 Parallel port connector table CN4 Parallel port IRQSerial ports CN11, CN5 COM2 RS-232/422/485 serial ports CN5IrDA connector CN6, Pin 1~5 Reset switch CN6, Pin6 External/internal Speaker CN6, Pin ~ 1 For external speaker connectionHard drive LED CN6, Pin 13 CPU fan power connector CN7 100Base-T Ethernet connector CN9 IDE hard drive connector CN10 CN10IDE hard drive connector CN10 Floppy drive connector CN12 CN12Connecting the floppy drive Floppy Drive Connector CN12 Floppy drive connector CN12 Pin SignalDiskOnChip socket U10 DiskOnChip DOC 2000 Installation Award Bios Setup Starting setup To Enter Setup Before Boot Press DEL KEYSetup keys These keys helps you navigate in SetupCase of Problems Getting helpMain setup Menu BiosPage Standard Cmos setup Hard Disks Award Bios Setup LCD & CRT Halt On Page Bios features setup Virus Warning Shadow Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Delayed Transaction Power management setup Power Management Determines the manner in which the monitor is blanked VGA Active Monitor Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Flat Panel/CRT Controller Display Drivers and Utilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsDriver Installation Page Place the Supporting CD-ROMin your CD-ROM drive Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Watchdog Timer Watchdog Timer Each Page Appendix a Watchdog Timer SelectDevice8 //Set Register F2 Select Device 8 SelectDevice8 //Set Register F3 Page Appendix a Watchdog Timer Installing PC/104 Modules PCM-3660 PC/104 module dimenstions inches ±5% Appendix B Installing PC/104 Modules