Emerson IPMC7126E, IPMC7616E Interrupt Routing to PIB, 11. PIB Interrupt Assignments, Programming

Page 37

Interrupt Routing to PIB

Chapter 3 Programming

Interrupt Routing to PIB

Module interrupts and MVME5100 Ethernet Port 2 interrupts go through the 8259 pair and into the PIB. The output of the PIB then goes to the Hawk MPIC on the MVME5100. The table below lists the ISA interrupts routed to the PIB.

Table 3-11. PIB Interrupt Assignments

PRI	IRQ	Controller	l	Polarity	Interrupt Source	Notes
	ISA		Edge/Leve
			Edge/Leve

1	IRQ0	INT1	Edge	High	Timer 1 / Counter 0	1

3-10	IRQ2		Edge	High	Cascade Interrupt from INT2

4	IRQ9	INT2	Level	High	Z8536 CIO	2,3

					Z85230 ESCC

5	IRQ10	INT2	Level	Low	PCI-Ethernet Interrupt (from	2,4
					MVME5100 Port 2)

9	IRQ14	INT2	Level	Low	PCI-SCSI Interrupt	2

11	IRQ3	INT1	Edge	High	COM2 (Async Serial Port 2)

12	IRQ4		Edge	High	COM1 (Async Serial Port 1)

15	IRQ7		Edge	High	Parallel Port Interrupt

Notes

1.Internally generated by the PIB.

2.After a reset, all ISA IRQ interrupt lines default to edge-sensitive mode.

3.Interrupts from the Z8536 and Z85230 devices are externally wired. External logic will determine which device to acknowledge during a pseudo IACK cycle. The Z8536 CIO has higher priority than the Z85230 ESCC. This IRQ MUST be programmed for level-sensitive mode.

4.This interrupt is routed from the MVME5100 through the IPMC connector to the module’s PIB to allow backward compatibility to other products.

IPMC7126E/7616E I/O Module Installation and Use (6806800A45B)

23

Image 37

Contents Installation and Use 6806800A45BIPMC7126E/7616E I/O Module Limited and Restricted Rights Legend TrademarksContact Address Use Caution When Exposing or Handling a CRT Safety SummaryGround the Instrument Do Not Operate in an Explosive AtmosphereEMI Caution FlammabilityCE Notice European Community Industrie Canada1 Product Features ContentsGeneral Functionality IPMC Mode Design Features PCI Bus Interface Configurable Switches PCI-to-ISA Bridge PIB SCSI4 Connector Pin Assignments ContentsIPMC712 Connector IPMC761 Connector PCI Interface and I/O Connectors A SpecificationsList of Figures viii IPMC7126E/7616E I/O Module Installation and Use 6806800A45B List of FiguresList of Tables Table B-1. Emerson Network Power - Embedded Computing PublicationsTable 3-3. IDSEL and IDSELB Mapping for PCI Devices x IPMC7126E/7616E I/O Module Installation and Use 6806800A45B List of TablesSummary of Changes About This ManualChapter 3, Programming Chapter 1, Product Features Chapter 2, Installing the IPMC ModuleTerminology Comments and SuggestionsConventions Used in This Manual About This ManualEnter, Return or CR xiiiCtrl xiv IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Design Features Product FeaturesGeneral Functionality IPMC ModeChapter 1 Product Features Configurable SwitchesS1 Switch S2 SwitchTable 1-1. IPMC761 Jumpers Figure 1-1. IPMC761 with Default Switch SettingSetting Jumper4 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Figure 1-2. IPMC761 Functional Block DiagramISA bus 2 AsyncTable 1-2. IPMC712 Jumpers Figure 1-3. IPMC712 with Default Switch Settings6 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Figure 1-4. IPMC712 Functional Block LayoutSCSI PMC P11 & P12Figure 1-5. IPMC712 Serial Port 4 Clock Configuration Static ROM SROM ISA Local Resource BusSuper I/O ESCCInput/Output Modes PCI Signaling Voltage LevelLEDs RS232 Interface10 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Configuring the IPMC Modules Installing the IPMC ModuleInstalling IPMC Modules on Host Board PackagingObserve ESD Precautions Before You Install or Remove a BoardFigure 2-1. IPMC Installation Chapter 2 Installing the IPMC ModuleUse Caution When Installing or Removing Boards Watch for Bent Pins or Other DamagePreserve EMI Compliance and component integrity before installationRecognize Different Injector/Ejector Lever Types your configurationVerify Slot Usage Figure 2-2. Injector/Ejector Lever TypesPrograming Details ProgrammingPCI Local Bus The PCI-to-ISA Bridge PIBFigure 3-1. GPIO Switch Settings S1 Table 3-2. SCSI Speed/Width Settings Using GPIO21,2Table 3-1. GPIO Pin Assignments Chapter 3 ProgrammingIDSEL Address Assignments for PCI Local Bus Figure 3-2. IDSEL Switch Settings S2MVME5100 PCI Arbitration Assignments on Host BoardsMVME5500 Table 3-3. IDSEL and IDSELB Mapping for PCI DevicesMVME6100 Interrupt AssignmentsMVME5100 IPMC Module Interrupt Assignments Table 3-6. Hawk MPIC Interrupt AssignmentsMVME6100 IPMC Module Interrupt Assignments MVME5500 IPMC Module Interrupt AssignmentsTable 3-7. Strap Pins Configuration Z8536 CIO Port PinsISA DMA Channels Table 3-8. PIB DMA Channel AssignmentsISA DMA Connections/Assignments Table 3-9. Z8536 CIO Port Pins AssignmentTable 3-10. DMA Connection/Assignments Table 3-11. PIB Interrupt Assignments Interrupt Routing to PIB24 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Vital Product Data VPDMVME5100 - via the Hawk ASIC IPMC761’s VPD address is $A4 MVME5500 - via the Discovery1 device GT64260IPMC712 Connector Connector Pin AssignmentsTable 4-1. IPMC712 Connector Table 4-2. IPMC761 Connector IPMC761 ConnectorChapter 4 Connector Pin Assignments 26 IPMC7126E/7616E I/O Module Installation and Use 6806800A45BTable 4-3. PCI Connector Pin Assignments P11 PCI Interface and I/O ConnectorsTable 4-4. PCI Connector Pin Assignments P12 Table 4-3. PCI Connector Pin Assignments P11 continued28 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Table 4-5. PCI Connector Pin Assignments P13 Table 4-4. PCI Connector Pin Assignments P12 continuedTable 4-6. PCI Connector Pin Assignments P14 Table 4-5. PCI Connector Pin Assignments P13 continued30 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Table 4-7. PCI Connector Pin Assignments P15 Table 4-6. PCI Connector Pin Assignments P14 continued32 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B General Specifications SpecificationsTable A-1. IPMC Specifications Table A-2. Power Consumption Power RequirementsAppendix A Specifications 34 IPMC7126E/7616E I/O Module Installation and Use 6806800A45BTable B-1. Emerson Network Power - Embedded Computing Publications Emerson Network Power - Embedded Computing DocumentsRelated Documentation PublicationTable B-2. Manufacturers’ Documents Manufacturers’ DocumentsAppendix B Related Documentation Table B-3. Related Specifications Related SpecificationsDocument Title and Source Page Index 40 IPMC7126E/7616E I/O Module Installation and Use 6806800A45B Index