5.5 Indicators and Messages
Error Messages
Table 5.3 Error Messages
Message | Corrective Action |
|
|
0HPRU\ RYHUIORZ | The total amount of data received by the printer exceeds the printer's internal mem- |
3UHVV &217,18( | ory. Try adding more memory (expansion RAM). Press the CONTINUE key to resume |
| printing. You can abandon printing by the CANCEL key. |
|
|
3ULQW RYHUUXQ | The data transferred to the printer was too complex to print on a page. Press the |
3UHVV &217,18( | CONTINUE key to resume printing. (The page may break in some pages.) |
| You can abandon printing by the CANCEL key. |
| Note: After this message has been displayed, Page protect mode will be On. To |
| maintain optimum use of memory during printing, displayý!3DJH SURWHFW |
| from the control panel, and |
| See the last page in this manual. |
|
|
.3'/ (UURU | Current print processing cannot continue. |
3UHVV &217,18( | To print out a error report, displayý!ý3ULQWý.3'/ýHUUV from the mode select |
| menu, and selectý2Q. |
| Press the CONTINUE key to resume printing. You can abandon printing by the CANCEL |
| key. |
|
|
5$0ý ',6.ý HUURUý úú | Check the error code displayed in the place ofýúúand refer to the appropriate descrip- |
3UHVVý &217,18( | tion below. |
| íì:Abnormal format. Try turning the power off and on again. |
| íë:RAM DISK mode isý2II. Turn RAM DISK modeý2Q. |
| íê:Cannot write to the disk system because it is write protected. Remove the write |
| protection. |
| íé:No disk space. Clean up files. |
| íè:Specified file not on disk. |
| íç:No memory for use by disk system. Expand printer memory. |
| ìí:Cannot format disk because host data is spooled there. Format the disk after |
| 5HDG\ is displayed. |
| äå:Unable to read files during the sorting (file does not exist, or corrupted). |
|
|
0(025< &$5' HUU | The memory card is accidentally removed from the printer's memory card slot during |
,QVHUW DJDLQ | reading. If you continue reading the memory card, insert the same memory card into |
| the slot again. The printer again reads it from the beginning of the data. |
| Note: We recommend that you follow the reading procedure from the begin- |
| ning to ensure correct reading of the memory card. |
|
|
,QVHUW WKH VDPH | You have inserted the wrong memory card when theý,QVHUWýDJDLQmessage was |
0(025< &$5' | displayed. Remove the wrong memory card from the printer's memory card slot and |
| insert the correct memory card. The printer again reads it from the beginning of the |
| data. |
|
|
)RUPDW HUURU | This message appears when the printer is in the ready state and the memory card is |
0(025< &$5' | not formatted, and therefore cannot be read or written. Follow the procedure on Sec- |
| |
|
|
:DUQLQJ EDWWHU\ | This message appears when the printer is in the ready state and the battery in the |
0(025< &$5' | memory card is low. You can still enter the memory card mode, but the battery should |
| be changed as soon as possible. |
|
|
%DWWHU\ HUURU | This message appears when the printer is in the ready state and the battery in the |
0(025< &$5' | memory card is dead, or there is no battery at all. It is not possible to use the memory |
| card mode until you insert a good battery in the card. |
|
|