List of Shipped Components | Kyocera 3750, FS1750 specs

1.2. Unpacking and Inspection

List of Shipped Components

❒(A) Face-up Output Tray (FS-3750 only)

❒(B) Toner Kit (Box for the Developer Unit)

❒(C) Power Cord

❒(D) User's Manual and Kyocera Digital Library (CD-ROM), including the printer drivers and manuals.

❒(E) Paper Stopper (FS-3750 only)

12

(A)

(B)

(D)

Printer

(C)

(E)

To remove the printer from the box, grasp the handholds on either side of the printer. Lift the printer from the carton as shown below.

☛ ‹ Always use these handholds when- ever you lift or move the printer.

‹The handhold on the right side of the printer doubles as the memory card

slot. Be sure to remove the memory card first, if inserted, before lifting or moving the printer.

1-4

Image 23

Kyocera 3750, FS1750 manual List of Shipped Components

Contents

FS-1750 FS-3750 Introduction Limitation of Remedies Limited WarrantyLicense Typeface Trademark Acknowledgement General Conforming to the Class B limits FCC statementConforming to the Class a limits Laser safety Interface connectorsSafety information Important note on the interface connectors Cdrh regulations Ozone concentration CE Marking Directive Declaration of Conformity U.S.A Declaration of Conformity Australia Viii Disclaimer Canadian Department of Communications compliance statementISO Moving the Printer Prolonged Non-Use and Moving the PrinterProlonged Non-use Kyocera ECO-PRODUCT Action program Energy Introduction Maintenance FeaturesPrint Engine Features Options Software Features Prescribe 2e Programming Manual on CD-ROM Guide to the ManualCD-ROM Kyocera Digital Library Table of Contents Xvi Xvii Xviii Places to Avoid Positioning the PrinterClearance Frequency Temperature 10C to 32.5C 50F to 90.5F Humidity 20% to 80%Basic requirements Voltage Unpacking and Inspection Power Supply List of Shipped Components Front View Names of Parts Rear View Interior View Setting Up and Interfacing Open the top cover Install the toner container Close the top cover Install the waste toner bottle Open the side cover on the left side of the printer Adjusting the paper guides in the cassette and adding paper Setting Up and Interfacing Open the paper stopper on the face-down output tray Install the face-up output tray if required Serial interface Attach the power cordConnect the printer to the computer Parallel interface Test the interface with the computer Set the emulation modePrint a status Windows 95/Windows Install the printer driver CD-ROM Drive Name\drivers\Language\pcl\9x CD-ROM Drive Name\drivers\Language\kpdl\9x Windows Duplex Printing from the MP tray First Mode Automatic Manual FeedingCassette Mode MP Multi-Purpose Tray Feeding 03 WUD\ Prgh Luvw First Mode Automatic Manual Feeding Feeding Envelopes Cassette Mode To Remove the Memory Card Memory CardHandling a Memory Card Removing the Main Circuit Board Memory Expansion Installation Withdrawing the Main Circuit Board from the Printer Simm to be used Installing and Removing SIMMsInstalling SIMMs Removing SIMMs Testing the Expansion Memory Control Panel Operating the Laser Printer Message Meaning Interface IndicatorResolution Indicator Message Display Copy Indicator Paper Size Indicator Indicator Name Description Symbolic Indicators Key Function Control Keys Feed Selection Operating ProceduresSwitching Power On Stack Selection Canceling Printing On-line/Off-line Setting Status Printout Sample Status Form Feed Function Default Setting Using the Mode Select MenuMode Select Menu 2SWïý 520ý ý ý ý ý ý ý Parallel Interface Configuring Interfaces RAM Disk Operations Setting the RAM Disk Size Writing Data to a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Reading Fonts/Data from a Memory Card Deleting Data from a Memory Card Printing a list of data names Formatting a Memory Card Keys to displayý!&DVVHWWHýVLHý Setting Custom Sizes Cassette, Media Type and Custom Settings Setting the Paper Type Paper Type User Setting Making Settings Submenus displayed Selection parameters Description Sleep Ecopower Mode Dumping Received Data Cancel key KIR 2 Level White vertical stripes Ecoprint ModeOptimized stripes Dark vertical stripes Resource Protection Adjusting the Print Density Type of Error and Corresponding Audio Alarm Buzzer Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Internal Fonts Fonts Font Number Font samples List of FontsInternal Scalable and Bitmap Fonts List of Fonts Kpdl Fonts List of Fonts Supplying Toner Toner Kit ReplacementToner kit replacement interval Toner Kit to be Used To replace the toner container, proceed as follows Toner Kit Replacement Replace the Waste Toner Bottle Do not cap the new waste toner bottle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Interface Problems Power Problems Check the developer unit Print Quality ProblemsCompletely blank printout All-black printout Check the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaks Grey background Faint or blurred printing Check the transfer roller Dirt on the top edge or back of the paperCharacters out of position Check the paper chute and the ramp Symbolic Indicators Indicators and MessagesIndicators Message Corrective Action Maintenance MessagesMaintenance Messages DOO Vhuylfh Ning to ensure correct reading of the memory card Error MessagesError Messages 0025&$5 HUUúú Correcting a Paper Jam Printer Symbol Rear Cover Printing speed ResolutionDrum cleaning FS-1750 FS-3750 Printing method Weight Description FS-1750 FS-3750 Power requirementsPower consumption Sound pressure level at Front Dimensions General Guidelines Paper SpecificationsTable B.1 Specifications Specification Paper Size Selecting the Right PaperCondition of the Paper Composition Thickness Caliper Basis WeightMoisture Content Smoothness Paper type Media type Special Paper Adhesive-Backed Labels Table B.3 OHP Film SpecificationsTable B.4 Adhesive Label Specifications Overhead Projection OHP Film Recycled Paper EnvelopesColored Paper Preprinted Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface SignalsTable C.1. Parallel Connector Pin Assignments Error* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit Pin RS-232C interface Interface SignalsRS-232C/RS-422A Interface Removing the Main Circuit Board RS-422A interface Verifying the Setting Changing the Jumper Connector RDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector RS-422A interface voltage levels RS-232C/RS-422A Protocol H7 Buffer nearly-empty threshold Prescribe 2e Frpo D0 commandRS-232C Cable Connection Preparing an RS-232C Cable Ctrl P \DIR Connecting the Printer to the Computer Data On Line Index Index-2 Index-3 Basic Operations During Mode Selection Mode Select Menu From Previous VLH Hyhorshu