Open the top cover, Install the toner container | Kyocera 3750

1.4. Setting Up and Interfacing

1—Open the top cover

1.	Remove the packing tape from the printer.	Top Cover
		Top Cover

2. Open the printer top cover all the way.

2—Install the toner container

1.Take the toner container from the toner kit.

2. With the label side down, thoroughly shake the toner container (in the direction of the arrow) ten times or more to loosen and mix the toner inside.

Toner Container

3.The bottom of the toner container is sealed with a sealing strip. Peel off the seal on the toner container and carefully pull off and dispose of the sealing strip.

☛Be sure to peel the seal off the toner container before the toner container is fitted into the devel- oper unit.

4.Install the toner container on the developer as show in the diagram.

Sealing strip

Developer Unit

1-8

Image 27

Kyocera 3750, FS1750 manual Open the top cover, Install the toner container

Contents

FS-1750 FS-3750 Introduction Limited Warranty LicenseLimitation of Remedies Typeface Trademark Acknowledgement General FCC statement Conforming to the Class a limitsConforming to the Class B limits Laser safety Interface connectorsSafety information Important note on the interface connectors Cdrh regulations Ozone concentration CE Marking Directive Declaration of Conformity U.S.A Declaration of Conformity Australia Viii Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the Printer Prolonged Non-useMoving the Printer Kyocera ECO-PRODUCT Action program Energy Maintenance Features Print Engine FeaturesIntroduction Options Software Features Guide to the Manual CD-ROM Kyocera Digital LibraryPrescribe 2e Programming Manual on CD-ROM Table of Contents Xvi Xvii Xviii Positioning the Printer ClearancePlaces to Avoid Frequency Temperature 10C to 32.5C 50F to 90.5F Humidity 20% to 80%Basic requirements Voltage Unpacking and Inspection Power Supply List of Shipped Components Front View Names of Parts Rear View Interior View Setting Up and Interfacing Open the top cover Install the toner container Close the top cover Install the waste toner bottle Open the side cover on the left side of the printer Adjusting the paper guides in the cassette and adding paper Setting Up and Interfacing Open the paper stopper on the face-down output tray Install the face-up output tray if required Serial interface Attach the power cordConnect the printer to the computer Parallel interface Set the emulation mode Print a statusTest the interface with the computer Windows 95/Windows Install the printer driver CD-ROM Drive Name\drivers\Language\pcl\9x CD-ROM Drive Name\drivers\Language\kpdl\9x Windows Duplex Printing from the MP tray First Mode Automatic Manual FeedingCassette Mode MP Multi-Purpose Tray Feeding 03 WUD\ Prgh Luvw First Mode Automatic Manual Feeding Feeding Envelopes Cassette Mode Memory Card Handling a Memory CardTo Remove the Memory Card Removing the Main Circuit Board Memory Expansion Installation Withdrawing the Main Circuit Board from the Printer Installing and Removing SIMMs Installing SIMMsSimm to be used Removing SIMMs Testing the Expansion Memory Control Panel Operating the Laser Printer Message Meaning Interface IndicatorResolution Indicator Message Display Copy Indicator Paper Size Indicator Indicator Name Description Symbolic Indicators Key Function Control Keys Feed Selection Operating ProceduresSwitching Power On Stack Selection Canceling Printing On-line/Off-line Setting Status Printout Sample Status Form Feed Using the Mode Select Menu Mode Select MenuFunction Default Setting 2SWïý 520ý ý ý ý ý ý ý Parallel Interface Configuring Interfaces RAM Disk Operations Setting the RAM Disk Size Writing Data to a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Reading Fonts/Data from a Memory Card Deleting Data from a Memory Card Printing a list of data names Formatting a Memory Card Keys to displayý!&DVVHWWHýVLHý Setting Custom Sizes Cassette, Media Type and Custom Settings Setting the Paper Type Paper Type User Setting Making Settings Submenus displayed Selection parameters Description Sleep Ecopower Mode Dumping Received Data Cancel key KIR 2 Level White vertical stripes Ecoprint ModeOptimized stripes Dark vertical stripes Resource Protection Adjusting the Print Density Type of Error and Corresponding Audio Alarm Buzzer Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Internal Fonts Fonts List of Fonts Internal Scalable and Bitmap FontsFont Number Font samples List of Fonts Kpdl Fonts List of Fonts Supplying Toner Toner Kit ReplacementToner kit replacement interval Toner Kit to be Used To replace the toner container, proceed as follows Toner Kit Replacement Replace the Waste Toner Bottle Do not cap the new waste toner bottle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Interface Problems Power Problems Check the developer unit Print Quality ProblemsCompletely blank printout All-black printout Check the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaks Grey background Faint or blurred printing Check the transfer roller Dirt on the top edge or back of the paperCharacters out of position Check the paper chute and the ramp Indicators and Messages IndicatorsSymbolic Indicators Maintenance Messages Maintenance MessagesMessage Corrective Action DOO Vhuylfh Error Messages Error MessagesNing to ensure correct reading of the memory card 0025&$5 HUUúú Correcting a Paper Jam Printer Symbol Rear Cover Printing speed ResolutionDrum cleaning FS-1750 FS-3750 Printing method Weight Description FS-1750 FS-3750 Power requirementsPower consumption Sound pressure level at Front Dimensions General Guidelines Paper SpecificationsTable B.1 Specifications Specification Paper Size Selecting the Right PaperCondition of the Paper Composition Thickness Caliper Basis WeightMoisture Content Smoothness Paper type Media type Special Paper Adhesive-Backed Labels Table B.3 OHP Film SpecificationsTable B.4 Adhesive Label Specifications Overhead Projection OHP Film Recycled Paper EnvelopesColored Paper Preprinted Paper Parallel interface communication modes Parallel Interface Interface Signals Table C.1. Parallel Connector Pin AssignmentsPin In/out Description Error* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit Pin Interface Signals RS-232C/RS-422A InterfaceRS-232C interface Removing the Main Circuit Board RS-422A interface Verifying the Setting Changing the Jumper Connector RDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector RS-422A interface voltage levels RS-232C/RS-422A Protocol H7 Buffer nearly-empty threshold Prescribe 2e Frpo D0 commandRS-232C Cable Connection Preparing an RS-232C Cable Ctrl P \DIR Connecting the Printer to the Computer Data On Line Index Index-2 Index-3 Basic Operations During Mode Selection Mode Select Menu From Previous VLH Hyhorshu