Cisco Systems 6503 manual and incompatible

Page 7
and incompatible.

Table 1 shows protocols and features for high availability as of Cisco Catalyst OS version 7.5 that are supported, compatible,

and incompatible.

Table 1 High Availability Feature Support

Supported Features

Compatible Features

Incompatible Features

 

 

 

COPS-DR and COPS-DR

ASLB

Dynamic VLANs

 

 

 

Dynamic Trunk Protocol

Cisco Discovery Protocol

Generic VLAN Registration Protocol

 

 

(GVRP)

 

 

 

Cisco Express Forwarding and adjacency

GMRP

Protocol filtering

tables

 

 

 

 

 

Private VLANs

Internet Group Management Protocol

 

 

(IGMP) snooping

 

 

 

 

Router access control lists (ACLs)

Remote Monitoring (RMON)

 

 

 

 

Multilayer switching (MLS)

Resource Reservation Protocol (RSVP)

 

 

 

 

Port Aggregation Protocol/Link

Simple Network Management Protocol

 

Aggregation Protocol (PAgP/LACP)

(SNMP)

 

 

 

 

Quality-of-service (QoS) ACLs and

Telnet sessions

 

policers

 

 

 

 

 

Switched Port Analyzer (SPAN)

VTP pruning

 

 

 

 

STP

Uplinkfast

 

 

 

 

Trunking

 

 

 

 

 

UniDirectional Link Detection (UDLD)

 

 

protocol

 

 

 

 

 

VLAN ACLs

 

 

 

 

 

VLAN Trunking Protocol (VTP)

 

 

 

 

 

Port Security

 

 

 

 

 

802.1X

 

 

 

 

 

For a current list of the features that are supported with the High Availability feature, see the “Configuring Redundancy” chapter of the Cisco Catalyst 6500 Series Software User Guide and the release notes.

Many Layer 3 and Layer 4 protocols or features are programmed into the application-specific integrated circuits (ASICs) of the PFC or PFC2 on board the supervisor engine. Examples of these include access lists (router- and VLAN-based), forwarding tables (multilayer switching cache and Cisco Express Forwarding tables), and QoS settings. The protocols are maintained in the protocol database and will continue to be switched in hardware when a supervisor engine failover occurs. Some of these are dependent on a dual MSFC configuration, which is discussed later in this paper.

The protocol state database, depicted in Figure 2 below, is a repository of up-to-date protocol state information. It is generated by the active supervisor and stored by the standby supervisor. The database contains specific system information including module and port states, VLAN information, nonvolatile RAM (NVRAM) configurations, and various protocol-specific data.

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 7 of 19

Image 7
Contents White Paper High Availability for the Cisco Catalyst 6500 Series SwitchesSwitching Fabric Failover Switch Fabric Module RedundancySwitching Fabric Operation CLI output description for show fabric channel switchmode Example 1 Fabric-Enabled SystemExample 2 Classic and Fabric-Enabled System Supervisor Fast Switchover Supervisor Engine SwitchoverRedundant Supervisor Engines Supervisor Stateful Protocol Redundancy Supervisor High Availability FeatureSup-A enable set system highavailability enable and incompatible Standby Supervisor Supervisor Engine Software Image UpgradesSupervisor Engine Image Synchronization Protocol DatabaseSup-A enable show system highavailability Supervisor Engine Versioning Feature6. Sup-A enable set boot system flash bootflashcat6000-sup2k8.7-2-2.bin Cisco Catalyst OS Image Upgrade ProcedureMSFC High Availability Features Dual Router Mode MSFC Configuration SynchronizationDRM Operation DRM Challenges WAN Interfaces in DRMSRM Operation Single Router ModeWAN Interfaces in SRM SRM Configuration and Conversion ProcedureSupervisor and MSFC Failover Tests SRM and IP MulticastRedundant Power Supplies Conclusion Asia Pacific Headquarters Corporate HeadquartersEuropean Headquarters Americas Headquarters