Cisco Systems IE301024TC manual Installing the Cisco Microsoft Windows USB Device Drivers

Page 88

Appendix C Configuring the Switch with the CLI Setup Program

Accessing the CLI Through the Console Port

Step 5 Configure the COM port.

Step 6 Configure the baud rate and character format of the PC or terminal to match the console port characteristics:

•9600 baud

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Step 7 Connect power to the switch as described in Chapter 3, “Power Supply Installation.”

Step 8 The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt. Follow the steps in the “Completing the Setup Program” section on page C-7.

Installing the Cisco Microsoft Windows USB Device Drivers

Installing the Cisco Microsoft Windows XP USB Driver

Step 1 Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

Note You can download the driver file from the Cisco.com software download site.

Step 2 If using 32-bit Windows XP, double-click the setup.exe file in the Windows_32 folder. If using 64-bit Windows XP, double-click the setup(x64).exe file in the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins.

Step 4 The Ready to Install the Program window appears. Click Install.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and to the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Installing the Cisco Microsoft Windows 2000 USB Driver

			Step 1	Obtain the file Cisco_usbconsole_driver.zip from Cisco.com, and unzip it.

				Note		You can download the driver file from the Cisco.com software download site.

			Step 2	Double-click the setup.exe file.
			Step 3	The Cisco Virtual Com InstallShield Wizard begins. Click Next.
			Step 4	The Ready to Install the Program window appears. Click Install.
			Cisco IE 3010 Switch Hardware Installation Guide
			Cisco IE 3010 Switch Hardware Installation Guide

	C-4					78-19581-02
	C-4					78-19581-02

Image 88

Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelAlarm Ports Power-Input TerminalSFP Module Patch Cable Alarm Output Alarm InputManagement Ports Switch Panel LEDs LEDsPower-Supply Module LEDs Alarm LEDsSystem LED Color System StatusConsole LEDs Port LEDsColor Description LED Color MeaningSD Flash Memory Card PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDNetwork Configurations Power Supply FeaturesManagement Options Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesGrounding the Switch Installing a Power-Supply ModuleEquipment That You Need Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Physical Specifications Switch SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable USB Console Port USB console port USB port on the PCInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6