Cisco Systems IE301024TC manual Switch Installation

Page 23

C H A P T E R 2

Switch Installation

Read the topics and perform the procedures in this order:

•Warnings, page 2-1

•Installation Guidelines, page 2-3

•Verifying Switch Operation, page 2-3

•Installing the Switch, page 2-4

•Installing and Removing SFP Modules, page 2-20

•Inserting and Removing the SFP Module Patch Cable, page 2-21

•Replacing the SD Flash Memory Card, page 2-23

•Connecting Devices to the Ethernet Ports, page 2-25

•Where to Go Next, page 2-27

Warnings

These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch document that ships on the documentation CD.

These warning statements apply to all the switches:

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Cisco IE 3010 Switch Hardware Installation Guide

	78-19581-02	2-1

Image 23

Contents Americas Headquarters Cisco IE 3010 Switch Hardware Installation GuidePage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Related Publications Obtaining Documentation and Submitting a Service RequestModel Description Switch ModelsCisco IE-3010-24TC Cable-Side View Cable SidePoE Ports 10/100 Fast Ethernet PortsDual-Purpose Ports Type of SFP Module Model SFP ModulesSFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output LEDs Switch Panel LEDsColor System Status Power-Supply Module LEDsAlarm LEDs System LEDLED Color Meaning Console LEDsPort LEDs Color DescriptionSD Flash Memory Card LED SD Flash Memory CardPoE LED Dual-Purpose Port LEDsPSU OK LED Power-Supply SideUSB LED Power-Supply Side LEDsManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Verifying Switch Operation Installation GuidelinesRack-Mounting Installing the SwitchAttaching Brackets for 19-Inch Racks 1and -2show how to attach brackets to the switches207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching 23-Inch Brackets Attaching Brackets for 23-Inch RacksAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets for IP-30 Compliance Optional Attaching BracketsRubber plug Switch-side User-supplied screws Wall-Mounting the Switch15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing SFP Modules Installing and Removing SFP ModulesRemoving SFP Modules Inserting and Removing the SFP Module Patch Cable18 Inserting an SFP Module Patch Cable Removing the SFP Module Patch Cable20 Loosening the Captive Screw Replacing the SD Flash Memory Card22 Removing the SD Flash Memory Card Connecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsDevice Crossover Cable Connecting to the 10/100 PoE PortsWhere to Go Next Page Power-Supply Modules Power Supply InstallationPower-supply module 3 Captive screw Installation Guidelines Power-Supply Module InstallationEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Crimping the Terminal Lug Installing the Power-Supply Module in the SwitchLoosen the Screws on the Power Supply Blank Wiring the Power SourceAC 5 A, DC 15 a Statement Opening the Power-Input Terminal Cover100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 AC power Removing the Power-Supply Module16 Removing the Power-Supply Module Page Switch Post Results Diagnosing ProblemsEthernet and Fiber-Optic Cables Switch LEDsSwitch Connections Bad or Damaged CableSFP Module Interface Settings10/100 and 10/100/1000 Port Connections 10/100 PoE Port ConnectionsAutonegotiation and Network Interface Cards Switch PerformanceSpanning Tree Loops Speed, Duplex, and AutonegotiationFinding the Switch Serial Number Resetting the Switch to the Factory Default SettingsSerial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power Specifications Power-Supply Module SpecificationsAlarm Ratings Page 10/100 Connector SpecificationsFigure B-2 Fiber-Optic SFP Module LC Connector SFP Module ConnectorsPin Alarm connection Alarm PortSFP Module Cables Cables and AdaptersGLC-EX-SMD Extended temperature SFPsTP3 Cable PinoutsDSR DTR CTS RTS Console Port Adapter PinoutsSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB console port USB port on the PC USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriversUsing the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB DriverCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6