Cisco Systems WSC385024TS, C3850NM210G Installing the Switch, StackPower Partitioning Examples

Page 45

Chapter 2 Switch Installation

Installing the Switch

StackPower Partitioning Examples

Figure 2-9and Figure 2-10show StackPower stacks of Catalyst 3850 switches with failover conditions. In Figure 2-9, the StackPower cable 2 is faulty. Therefore, this stack does not provide redundancy.

Figure 2-9 Example of a StackPower Stack with a Failover Condition

1

2

3

344188

In Figure 2-10, StackPower port B on the center switch has failed and this stack partitions into two stacks. The top two switches share power, and the bottom switch is now a separate stack.

Figure 2-10 Example of a Partitioned StackPower Stack with a Failover Condition

1

2

344189

Installing the Switch

•Rack-Mounting, page 2-12

•Table- or Shelf-Mounting, page 2-16

•After Installing the Switch, page 2-16

The illustrations shown in this section show the Catalyst 3850-48 PoE+ switch as an example. You can install other Catalyst 3850 switches following the same procedures.

 

 

Catalyst 3850 Switch Hardware Installation Guide

 

 

 

 

 

 

OL-26779-02

 

 

2-11

 

 

 

 

 

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Catalyst 3850 Switch Hardware Installation Guide Page N T E N T S Installing and Removing SFP and SFP+ Modules Grounding the Switch Power Supply Module Specifications A-2 Installing the Cisco Microsoft Windows USB Device Driver C-4 Viii Preface PurposeDocument Conventions Related Documentation Obtaining Documentation and Submitting a Service RequestProduct Overview Switch Models, Front Panel, Rear Panel, Management Options,Switch Model Cisco IOS Image Description Switch ModelsSwitch Model Cisco IOS Image Description Front Panel Catalyst 3850-48P-L Switch Front PanelPoE, PoE+, and Cisco Upoe Ports 10/100/1000 Ethernet PortsUSB Mini-Type B Port Management PortsNetwork Modules USB Type a PortNetwork Module Description SFP and SFP+ Modules3 4 5 LEDsColor XPS Status Color System StatusMode LED Port Mode Description Port Mode Port LED Color MeaningPort LEDs and Modes 10/100/1000/SFP ports Color USB Console LEDColor Description Actv LEDPoE LED Color Status of PoE mode PoE, PoE+, or Cisco UpoeColor Network Module Link Status Network Module LEDsRear Panel RJ-45 Console Port LEDRJ-45 Console Port Status StackWise Ports Power Supply ModulesModels Default Power Supply Available PoE Number of Power Models Supplies Available PoEPoE Option Port Switch PoE Option Port Switch AC-Power Supply Module LEDs DC-Power Supply Module LEDsFan Modules Fan Module Description StackPower ConnectorManagement Options Ethernet Management PortRJ-45 Console Port Network Configurations Switch Installation Preparing for InstallationSafety Warnings OL-26779-02 Installation Guidelines Verifying Switch Operation Planning a Switch Data StackPowering Off the Switch Tools and EquipmentSwitch Stacking and Power Stacking Guidelines Data Stack Cabling Configurations344185 Data Stack Bandwidth and Partitioning ExamplesExample of a Data Stack with a Failover Condition Power-On Sequence for Switch Data StacksStackPower Stacking Guidelines Planning a StackPower StackPart Number Cable Type Length StackPower Cabling ConfigurationsStackPower Ring Topology StackPower Partitioning Examples Installing the SwitchRack-Mounting 11 Rack-Mounting Brackets Attaching the Rack-Mount Brackets12 Attaching Brackets for 19-inch Racks 13 Mounting the Switch in a Rack Mounting the Switch in a RackTable- or Shelf-Mounting After Installing the SwitchCisco logo Connector screw Connecting to the StackWise Ports16 Connecting the StackPower Cable to a StackPower Port Connecting to the StackPower PortsInstalling and Removing SFP and SFP+ Modules Installing a Network Module in the SwitchConnecting Devices to the Ethernet Ports 10/100/1000 Ethernet Port ConnectionsDevice Crossover Cable PoE+ and Cisco Upoe Port ConnectionsWhere to Go Next OL-26779-02 Overview Installing a Network ModuleCaptive screws Gigabit Ethernet ports Blank module Captive screws Color Link Status Network Module LEDsInstalling Network Modules Installing the Network Module in the Switch C3850-NM-4-1G module Configuring a Network ModuleC3850-NM-4-10G module Interface ActionC3850-NM-2-10G module Supported GBICsTenGigabitEthernet GigabitEthenet Installing SFP and SFP+ Modules Removing a Network ModuleSFP and SFP+ Modules Installing an SFP Module in the Network Module Removing SFP or SFP+ Modules Finding the Network Module Serial NumberNetwork Module Serial Number Location Power Supply Installation Power Supply Module OverviewPart Number Description AC OK LED AC Power Supply Module 6 5 Installation Guidelines AC Power Supply Module LEDsDC Power Supply Module LEDs Installing or Replacing an AC Power Supply Inserting the AC-Power Supply in the Switch Installing a DC Power SupplyEquipment That You Need Grounding the SwitchStripping the Ground Wire 10 Attaching the Ground Lug and Wire Assembly Wiring the DC Input Power Source Installing the DC Power Supply in the Switch12 DC Source a Isolated From Source B with No Common Ground Finding the Power Supply Module Serial Number14 1100-W AC Power Supply Serial Number 16 440-W DC Power Supply Module Serial Number Installing the Fan Installing a Fan Module Fan Module InstallationFinding the Fan Module Serial Number Installing the Fan ModuleFan Module Serial Number Diagnosing Problems TroubleshootingSwitch Post Results Switch LEDsBad or Damaged Cable Switch ConnectionsEthernet and Fiber Cables Link Status10/100/1000 Port Connections PoE and PoE+ Port ConnectionsSFP Modules Interface Settings Switch PerformancePing End Device Spanning Tree LoopsResetting the Switch Autonegotiation and Network Interface CardsCabling Distance Replacing a Failed Data Stack Member Finding the Switch Serial NumberSwitch Specifications Technical SpecificationsPhysical Specifications Environmental RangesPower Specifications Power Supply Module SpecificationsPower Specifications Fan Module Specifications Physical SpecificationOperating Specification Connector and Cable Specifications Connector Specifications10/100/1000 Ports SFP and SFP+ Modules Gigabit Ethernet CX1 SFP+ Copper Connectors10/100/1000 Ethernet Management Port Figure B-4 Simplex LC Cable ConnectorFigure B-7 10/100 Port Pinouts Console PortCable and Adapter Specifications SFP and SFP+ Module Cable SpecificationsStackWise Cables Two Twisted-Pair Cable Pinouts Four Twisted-Pair Cable PinoutsIdentifying a Crossover Cable Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts DeviceGND Switch Console RJ-45-to-DB-25 Port DTE OL-26779-02 Configuring the Switch with the CLI-Based Setup Program Accessing the CLIAccessing the CLI Through Express Setup USB Console Port Accessing the CLI Through a Console Port344194 Uninstalling the Cisco Microsoft Windows USB Driver Installing the Cisco Microsoft Windows USB Device DriverEntering the Initial Configuration Information IP SettingsConfiguring the Setup Program Enter an enable password, and press Return These choices appear OL-26779-02

C3850NM41G, C3850NM210G, WSC385024TS specifications

Cisco Systems is a global leader in networking and telecommunications hardware, and its Catalyst series of switches are widely recognized for their innovation, reliability, and performance. Among the numerous models available, the Cisco WSC385024TS, C3850NM41G, and C3850NM210G stand out for their advanced features and capabilities tailored to meet the needs of modern enterprises.

The Cisco WSC385024TS is a stackable switch that offers 24 ports, and it is built on Cisco's IOS XE software. It is designed for high-density environments, making it ideal for organizations that require robust connectivity and scalability. This model supports advanced Layer 2 and Layer 3 features and facilitates intelligent traffic management through Quality of Service (QoS). One of its standout features is the ability to stack up to nine switches together, enabling centralized management and increased fault tolerance. The WSC385024TS also integrates security features such as 802.1X authentication and access control lists, which are essential for maintaining a secure network infrastructure.

The C3850NM41G is a versatile switch that comes with 41 Gigabit Ethernet ports, making it suitable for environments that demand high-speed connectivity. This model supports Cisco's innovative StackWise-480 technology, which provides increased bandwidth and reliable inter-switch communication. Additionally, it features Power over Ethernet (PoE) capabilities, allowing it to deliver power to connected devices such as IP phones and wireless access points, thereby simplifying cabling and reducing the need for additional power sources. The C3850NM41G is also equipped with built-in automatic fault detection and recovery, enhancing the overall resilience of the network.

Lastly, the C3850NM210G model offers 210 Gbps of switching capacity, making it ideal for data-intensive applications. This switch combines performance with security, supporting various security protocols such as Virtual Routing and Forwarding (VRF) and Dynamic Host Configuration Protocol (DHCP) snooping to protect against malicious activity. With its modular design, the C3850NM210G allows for easy upgrades and expansions, facilitating adaptive network growth.

In summary, the Cisco WSC385024TS, C3850NM41G, and C3850NM210G switches provide advanced features, robust performance, and high scalability, making them ideal choices for businesses aiming to enhance their network infrastructure while supporting cutting-edge technologies. Whether for small businesses or large enterprises, these models exemplify Cisco's commitment to delivering high-quality networking solutions that adapt to the evolving demands of today's digital landscape.
Top Page Image Contents