Cisco Systems BC-145 manual Configuring Source-Route Bridging over Trisl, BC-151

Page 7

Configuring Token Ring Inter-Switch Link

TRISL Configuration Task List

Note The default IPX encapsulation format for Token Ring in Cisco IOS routers is SAP. Therefore, you only need to explicitly configure the IPX encapsulation type if your Token Ring network requires SNAP encapsulation instead of SAP.

When routing source-routed traffic for specific VLANs, use the following additional commands in interface configuration mode:

 

Command

Purpose

Step 1

 

 

Router(config-if)# multiring

Creates a pseudoring to terminate the RIF and assign it to a VLAN.

 

trcrf-vlan vlanid trcrf-ring

 

 

ring-number

 

Step 2

 

 

Router(config-if)# multiring

Enables collection and use of RIF information with routed protocols.

 

{protocol-keyword [all-routes

 

 

spanning all other]}

 

 

 

 

Configuring Source-Route Bridging over TRISL

To configure SRB over TRISL, use the following commands beginning in global configuration mode:

 

Command

Purpose

Step 1

 

 

Router(config)# source-bridge

Configures a virtual ring for the router.

 

ring-group vring-num

 

Step 2

 

 

Router(config)# interface type

Specifies the subinterface on which TRISL will be used.

 

slot/port.subinterface-number

 

Step 3

 

 

Router(config-if)# encapsulation

Defines the encapsulation for TRISL.

 

tr-isl trbrf-vlan vlanid bridge-num

 

 

bridge-number

 

Step 4

 

 

Router(config-if)# source-bridge

Attaches a TrCRF VLAN identifier to the router’s virtual ring.

 

trcrf-vlan vlanid ring-group

 

 

ring-number

 

 

 

 

Configuring Source-Route Transparent Bridging over TRISL

To configure transparent bridging over TRISL, use the following command beginning in global configuration mode:

 

Command

Purpose

Step 1

 

 

Router(config)# interface type

Specifies the subinterface on which TRISL will be used.

 

slot/port.subinterface-number

 

Step 2

 

 

Router(config-if)# encapsulation

Defines the encapsulation for TRISL.

 

tr-isl trbrf-vlan vlanid bridge-num

 

 

bridge-number

 

Step 3

 

 

Router(config-if)# bridge-group

Specifies the bridge group to which the TRISL subinterface belongs.

 

bridge-group number

 

 

 

 

 

 

Cisco IOS Bridging and IBM Networking Configuration Guide

 

 

 

 

 

 

 

78-11737-02

 

 

BC-151

 

 

 

 

 

Image 7
Contents ISL and Trisl Cisco’s Trisl ImplementationBC-145 BC-146 BC-147 Token Ring VLANsBC-148 Configuring IP Routing over TrislBC-149 Configuring Hot Standby Router Protocol over TrislBC-150 Configuring IPX Routing over TrislConfiguring Source-Route Transparent Bridging over Trisl Configuring Source-Route Bridging over TrislBC-151 BC-152 Configuring Source-Route Translational Bridging over TrislBC-153 Monitoring Trisl StatisticsBC-154 Trisl Configuration ExamplesBC-155 Following is the configuration for the router5500 BC-156BC-157 BC-158 IP Routing Source-Routed Frames Between Trisl VLANs ExampleEncapsulation tr-isl trbrf 999 bridge-num BC-159BC-160 BC-161 BC-162 IPX Routing Source-Routed Frames Between Trisl VLANs ExampleBC-163 SRB Between Token Ring and Trisl Vlan ExampleBC-164 SRB Between Trisl VLANs ExampleBC-165 Transparent Bridging Between Token Ring and Trisl Vlan BC-166SR/TLB Between a Trisl Vlan and an Ethernet Interface BC-167Set vlan 999 type trbrf bridge 0xe stp ibm BC-168BC-169 Trisl with Fast EtherChannel ExampleBC-170