Cisco Systems SRW248G4P manual Port Management Link Aggregation, Port Broadcast Control

Page 22

Chapter 5

Configuring the Switch

The following capabilities are supported..

•10half  Supports 10 Mbps half-duplex operation

•10full  Supports 10 Mbps full-duplex operation

•100half  Supports 100 Mbps half-duplex operation

•100full  Supports 100 Mbps full-duplex operation

•1000half  Supports 1000 Mbps half-duplex operation

•1000full  Supports 1000 Mbps full-duplex operation

•Sym  (Gigabit only)  Check this item to transmit and receive pause frames, or clear it to autonegotiate the sender and receiver for asymmetric pause frames..

Flow Control  Allows automatic or manual selection of flow control..

Port Broadcast Control

Status  To enable broadcast control on a specified port, mark the Enabled checkbox for that port..

Threshold  You can protect your network from broadcast storms by setting a threshold for broadcast traffic for all ports.. Any broadcast packets exceeding the specified threshold will then be dropped..

After you modify the required port settings, click Apply..

Port Management > Link Aggregation

You can create multiple links between devices that work as one virtual, aggregate link (LAG).. An aggregated link offers a dramatic increase in bandwidth for network segments where bottlenecks exist, as well as providing a fault-tolerant link between two devices.. You can create up to four LAGs on the Switch.. Each LAG can contain up to eight ports..

Port Management > Link Aggregation

LAG  Displays the LAG number..

Description  Displays the description assigned to the interface..

Administrative Status  Indicates whether the interface is enabled or disabled..

Type  Indicates if a LAG has been manually configured (static) or dynamically set through LACP..

Link Status  Displays the status of the link.. Speed  Displays the port speed..

Duplex  Displays the duplex mode.. Flow Control  Displays the flow control..

Create  To create a new LAG, click the Create button in the Create column, then add members to the LAG by clicking on the Select Member button.. The select member screen for the Link Aggregation opens..

Port Management > Link Aggregation > Select Member

The LAG number is shown in the LAG drop-down menu.. The Ethernet ports are represented by check boxes.. Assign up to 8 ports to the LAG by checking the checkboxes of the ports, then click Apply..

Detail  To configure the LAG and the LAG broadcast control, click the Detail button.. The Link Aggregation detail screen will be displayed..

Port Management > Link Aggregation > Detail

48-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents User Guide Table of Contents ACL Appendix E Contact Information Appendix a About Gigabit Ethernet and Fiber Optic CablingOnline Resources About This GuideIcon Descriptions Copyright and TrademarksChapter Chapter IntroductionChapter Product Overview Front PanelBack Panel Side PanelPlacement Options Pre-Installation ConsiderationsOverview Desktop Placement Hardware InstallationUplinking the Switch Rack-Mount PlacementChapter Configuration Using Console Interface Configuring the HyperTerminal ApplicationSystem Configuration Menu LoginSwitch Main Menu System ConfigurationManagement Settings User & Password SettingsIP Configuration IP Address SettingsReboot System Restore System Default SettingsFile Management Port Status Port ConfigurationPoE Configuration Back to Main MenuPort PoE Status System PoE ConfigurationPort PoE Configuration LogoutSetup Summary SetupDevice Information PoE Information Setup Network SettingsSystem Information IdentificationSetup Time Set TimeEdit Port Settings Port Management Port SettingsPort Management Port Management Link Aggregation Port Broadcast ControlPort Setting Port Management PoE Power SettingsGlobal Setting Port Management LacpVlan Management Create Vlan Vlan Management Port SettingsVlan Management Create VlanVlan Management Ports to Vlan Vlan Management Vlan to PortsStatistics Rmon Statistics StatisticsStatistics Rmon History Statistics Rmon Alarms Statistics Rmon EventsStatistics Port Utilization Statistics 802.1x StatisticsACL IP based ACL ACL MAC based ACLSecurity Security Authentication ServersRadius Server Setting Security ACL BindingSecurity 802.1x Settings Tacacs Server SettingSecurity Ports Security Security Https Settings Security Management ACLSecurity SSH Settings Security SSH Host-Key SettingsQoS QoS CoS SettingsCoS to Queue Queue Settings QoS Queue SettingsQoS Dscp Settings Port to CoSQoS DiffServ Settings Class MapPolicy Map QoS DiffServ Port Binding Spanning TreeQoS Bandwidth Spanning Tree STP Status Spanning Tree Global STPSpanning Tree STP Port Settings Spanning Tree STP Port Settings STP Port Setting Detail Spanning Tree Rstp Port Settings Spanning Tree Mstp Instance Settings Spanning Tree Mstp PropertiesSpanning Tree Mstp Interface Settings Multicast Multicast Global Settings Multicast Static Member PortsMulticast Member Ports Query Multicast Static Router PortsMulticast Router Ports Query Snmp Global Parameters Snmp Views Snmp Group ProfileSnmp Communities User AuthenticationSnmp Group Membership Data PrivacySnmp Notification Recipient AdminAdmin User Authentication SNMPv1,2Address Aging Admin Forwarding DatabaseStatic Address Setting Dynamic Address QuerySystem Logging Admin LogSyslog Admin Port Mirroring Smtp SettingAdmin Ping Admin Cable TestAdmin Save Configuration Admin Firmware Upgrade Admin Jumbo FrameAdmin Http Upgrade Admin Reboot Admin Factory DefaultGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Appendix B Appendix B GlossaryGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix B Appendix C Specifications Appendix CSpecifications Appendix D Warranty and Regulatory Information Limited WarrantyIndustry Canada Canada Safety NoticesFCC Statement IC StatementDansk Danish Miljøinformation for kunder i EU La Directiva 2002/96/CE de la UE exige que los equipos que Norsk Norwegian Miljøinformasjon for kunder i EU WEB For additional information, please visit Appendix E

SRW248G4P specifications

Cisco Systems SRW248G4P is a high-performance Layer 2 switch designed specifically for small to medium-sized businesses that require robust networking solutions. This switch supports Power over Ethernet (PoE), providing a highly flexible option for powering devices such as IP phones, wireless access points, and surveillance cameras.

One of the standout features of the SRW248G4P is its 48 10/100 Ethernet ports, which ensure ample connectivity for various networked devices. Additionally, it offers four Gigabit Ethernet uplink ports, allowing for seamless integration with existing network infrastructure and facilitating high-speed data transfer. The combination of these ports enables businesses to expand their network capabilities as needed without the immediate requirement for added devices.

The SRW248G4P comes equipped with advanced Layer 2 switching capabilities, including VLAN support, which enables the segmentation of network traffic for improved performance and security. It also supports Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP), which help prevent network loops and ensure redundancy. With features like Link Aggregation Control Protocol (LACP), multiple physical connections can be combined into a single logical link, enhancing bandwidth and providing failover capabilities.

Another critical attribute of the Cisco SRW248G4P is its user-friendly management interface. The switch can be managed through a web-based interface, allowing IT administrators to configure settings, monitor performance, and troubleshoot issues with ease. Additionally, it supports SNMP (Simple Network Management Protocol) for integration with network management systems, further simplifying monitoring tasks.

Power over Ethernet functionality is a significant advantage of the SRW248G4P, providing up to 15.4 watts per port. This capability simplifies installation and reduces the clutter of power cords and outlets. Organizations can deploy PoE-enabled devices in locations that lack power sources, thus enhancing overall flexibility in network design.

In summary, the Cisco Systems SRW248G4P is a feature-rich switch tailored for small to medium-sized enterprises. Its blend of performance, management capabilities, and advanced features like PoE makes it a valuable asset in any organization's networking setup. By ensuring reliable connectivity and ease of management, businesses can focus more on growth and their core objectives rather than worrying about network complexities.
Top Page Image Contents