Cisco Systems PA-POS-2OC3, PA-POS-1OC3 manual OL-6514-04

Page 54

Chapter 3 Removing and Installing the PA-POS-1OC3

Port Adapter Removal and Installation

Cisco 7304 PCI Port Adapter Carrier Card—Removing and Installing a Port Adapter

You can install one single-width port adapter in a Cisco 7304 PCI port adapter carrier card. This section provides step-by-step instructions for removing and installing a port adapter in a Cisco 7304 PCI port adapter carrier card.

Caution When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the Cisco 7304 PCI port adapter carrier card.

Note If the Cisco 7304 PCI port adapter carrier card is still in the router, you must remove the port adapter carrier card before removing a port adapter.

To remove and install a port adapter in a Cisco 7304 PCI port adapter carrier card, refer to Figure 3-2and do the following:

Step 1 To remove the port adapter from the Cisco 7304 PCI port adapter carrier card, turn the port adapter lock from its locked and horizontal position shown in A of Figure 3-2to its unlocked and vertical position shown in B of Figure 3-2.

Step 2 Ensure that the cables are disconnected from the port adapter before removing the Cisco 7304 PCI port adapter carrier card from the chassis.

Step 3 Grasp the handle of the port adapter and pull the port adapter from the Cisco 7304 PCI port adapter carrier card.

Step 4 To insert the port adapter in the Cisco 7304 PCI port adapter carrier card, locate the guide rails inside the Cisco 7304 PCI port adapter carrier card that hold the port adapter in place. They are at the top left and top right of the port adapter slot and are recessed about an inch, as shown in C of Figure 3-2.

Step 5 Carefully slide the port adapter in the Cisco 7304 PCI port adapter carrier card until the port adapter makes contact with the port adapter interface connector. When fully seated, the port adapter front panel should be flush with the face of the Cisco 7304 PCI port adapter carrier card.

Step 6 After the port adapter is properly seated, turn the port adapter lock to its locked and horizontal position, as shown in A of Figure 3-2.

PA-POS-1OC3 Single-Port Port Adapter Installation and Configuration Guide

3-8

OL-6514-04

 

 

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Americas Headquarters Text Part Number OL-6514-04Copyright 2007 Cisco Systems, Inc. All rights reserved N T E N T S Cisco 7401ASR Router Cisco 7401ASR Router-Removing and Installing a Port Adapter OL-6514-03 Document Version History ObjectivesVersion Date Organization Related DocumentationSection Title Description Preface Related Documentation OL-6514-04 PA-POS-1OC3 Overview PA-POS-1OC3 OverviewSONET/SDH Overview SDH EquivalentFeatures Interface Specifications OC-3 Optical Fiber SpecificationsNetwork Management Support Encapsulation Method Support Using Statistics to Estimate Link Loss and Power BudgetLEDs LED Label Color State FunctionCables and Connectors RCVPort Adapter Slot Locations on the Supported Platforms Cisco 7200 VXR Routers Slot NumberingCisco 7201 Router Slot Numbering Cisco 7200 Series VXRCisco 7301 Router Slot Numbering Cisco 7304 PCI Port Adapter Carrier Card Slot NumberingCisco 7401ASR Router Slot Numbering Module Slots on the Cisco 7304 RouterCisco 7500 Series Routers with VIP Slot Numbering 10 VIP Slot LocationsCisco 7505 Router Slot Numbering RSPCisco 7507 Router Slot Numbering VIP interface-slot RSP-slotCisco 7513 Router Slot Numbering 6 8 10Cisco 7603 Router Slot Numbering SUPERVISOR2Cisco 7606 Router Slot Numbering Cisco 7609 Router Slot Numbering FAN StatusCisco 7613 Router Slot Numbering Identifying Interface Addresses Platform Interface Address Format Numbers SyntaxCisco 7200 VXR Routers Interface Addresses Cisco 7201 Router Interface AddressesCisco 7301 Router Interface Addresses Cisco 7401ASR Router Interface Addresses Cisco 7500 Series Routers VIP Interface AddressesCisco 7600 Series Routers FlexWAN Module Interface Addresses OL-6514-04 Preparing for Installation Required Tools and EquipmentSoftware and Hardware Requirements Cisco 7200 VXR RoutersPlatform Recommended Minimum Cisco IOS Release Checking Hardware and Software Compatibility Safety Guidelines Safety WarningsWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger OL-6514-04 Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageLaser Safety FCC Class a ComplianceOL-6514-04 Removing and Installing the PA-POS-1OC3 Handling Port AdaptersOnline Insertion and Removal Handling a Port AdapterOIR Functional Description Port Adapter Removal and Installation Step Cisco 7201 Router-Removing and Installing a Port Adapter CiscoCisco 7301 Router-Removing and Installing a Port Adapter OL-6514-04 CC-PA Cisco 7401ASR Router-Removing and Installing a Port Adapter With the screw removed, grasp Screw Connecting PA-POS-1OC3 Interface Cables TX RXReplacing the SFP Optics Module Handling the SFP Optics ModuleRemoving the SFP Optics Module Installing the SFP Optics Module Verifying the SFP Optics Module Installation Inserting an SFP Optics ModulePage OL-6514-04 Configuring the PA-POS-1OC3 Using the Exec Command InterpreterConfiguring the Interfaces Parameter Configuration Commands Default ValuePlatform Command Example Shutting Down an InterfaceSlot/port-adapter/port Show interfaces pos, followed by Performing a Basic Configuration Show interfaces pos followed byInterface pos, followed by Customizing the Configuration Setting the MTU Size Configuring FramingSetting the Source of the Transmit Clock Configuring Cyclic Redundancy Checks Configuring Sonet Payload ScramblingConfiguring APS Basic APS ConfigurationChecking the Configuration Using show Commands to Verify the New Interface StatusCommand Function Example Show controllers Using the show version or show hardware Commands Cisco 7201 Router-Example Output of the show version Command Router#show version Using the show diag Command Port adapter is analyzedCisco 7201 Router-Example Output of the show diag Command Router#show diag Using the show interfaces Command Router# show interfaces pos 4/0 PE3#sh int pos4/1Router# show interfaces Using the ping Command to Verify Network Connectivity Router# ping 10.0.0.10 ReturnUsing loopback Commands Configuring an Interface for Internal LoopbackConfiguring an Interface for Line Loopback Push Mode Description Making a Back-to-Back Connection PA-POS-1OC3 Error MessagesPA-POS-1OC3 Statistics Counters First routerConfiguring the PA-POS-1OC3 Making a Back-to-Back Connection

PA-POS-1OC3, PA-POS-2OC3 specifications

Cisco Systems has long been at the forefront of networking technology, providing solutions that empower organizations to enhance their connectivity and communication capabilities. Among its impressive lineup, the PA-POS-2OC3 and PA-POS-1OC3 modules stand out as significant components designed to optimize performance in service provider and enterprise environments.

The PA-POS-2OC3 and PA-POS-1OC3 modules are designed for use with the Cisco 7600 Series routers and are tailored for Packet Over SONET (POS) transport. Supporting the OC-3 speed of 155.52 Mbps, these modules provide reliable high-speed connectivity, enabling organizations to efficiently manage data traffic and ensure rapid data transfer across their networks. The PA-POS-2OC3 offers dual OC-3 capabilities, allowing for higher aggregate bandwidth and redundancy options, making it common in demanding network environments.

One of the main features of the PA-POS-2OC3 and PA-POS-1OC3 is their enhanced support for advanced networking protocols, including MPLS (Multiprotocol Label Switching). MPLS facilitates efficient data routing and improves bandwidth utilization by enabling multiple types of traffic to be consolidated over a single network. This is crucial for organizations looking to deploy services like VoIP, video conferencing, and other bandwidth-intensive applications.

The modules also offer robust error correction and monitoring capabilities, which are essential for maintaining service quality in mission-critical applications. Administrators can monitor performance and diagnose issues in real-time, enabling swift responses to potential concerns that could disrupt service.

Moreover, the PA-POS-2OC3 and PA-POS-1OC3 are designed with features that support enterprise-grade security and scalability. This is particularly beneficial for organizations expecting growth or requiring enhanced protection for sensitive data as it traverses the network.

In summary, Cisco's PA-POS-2OC3 and PA-POS-1OC3 modules represent essential building blocks for high-speed networking solutions. Their support for OC-3 connectivity, advanced routing protocols, and robust monitoring capabilities make them ideal for both service providers and enterprises. Through increased scalability, improved bandwidth management, and enhanced security, these modules allow organizations to adapt to the ever-evolving landscape of data communications effectively. With Cisco at the helm, businesses can trust in a networking solution that not only meets current demands but is also primed for future growth.
Top Page Image Contents