Cisco Systems PA-POS-2OC3 manual Cisco 7401ASR Router-Removing and Installing a Port Adapter

Page 56

Chapter 3 Removing and Installing the PA-POS-1OC3

Port Adapter Removal and Installation

Cisco 7401ASR Router—Removing and Installing a Port Adapter

Step 1

To remove the port adapter, use a number 2 Phillips latch. Rotate the port adapter latch until it clears the rotate 360˚.

screwdriver to loosen the screw on the port adapter faceplate of the port adapter. (See A.) The latch can

Unlocked Locked

 

D

 

 

R

 

LE

S

CARR

IE

NAB

CELL

LARM

E

RX

RX

RXA

TX X

A

R

ENHANCED ATM

Step 2

Pull the port adapter from the router, about halfway out of its slot. (If you remove a blank port adapter, keep the blank port adapter for use in the router if you should ever remove the port adapter. The port adapter slot must always be filled.)

Step 3

With the port adapter halfway out of the slot, disconnect all cables from the port adapter. After disconnecting the cables, pull the port adapter completely out of the chassis slot.

Step 4

To insert the port adapter, locate the port adapter slot guides inside the Cisco 7401ASR router. They are near the top, and are recessed about 1/2 inch. (See B.)

Caution

The port adapter must slide into the slot guides under the chassis lid. Do not allow the port adapter components to come in contact with the system board, or the port adapter could be damaged.

B

ENABLED

RX

CELLS

CARRIERALARM

TX

 

 

RX

RX

 

 

 

 

 

RX

ENHANCED ATM

 

 

 

 

 

57643

Step 5

Insert the port adapter in the slot guides halfway, and then reconnect the port adapter cables.

Step 6

After the cables are connected, carefully slide the port adapter all the way into the slot until the port adapter is seated in the router midplane. When installed, the port adapter input/output panel should be flush with the face of the router.

Step 7

After the port adapter is properly seated, rotate the port adapter latch to the upright locked position and use a number 2 Phillips screwdriver to tighten the latch screw. If needed, loosen the latch screw to rotate the latch over the port adapter. Finish the installation by tightening the latch screw.

PA-POS-1OC3 Single-Port Port Adapter Installation and Configuration Guide

3-10

OL-6514-04

 

 

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Americas Headquarters Text Part Number OL-6514-04Copyright 2007 Cisco Systems, Inc. All rights reserved N T E N T S Cisco 7401ASR Router Cisco 7401ASR Router-Removing and Installing a Port Adapter OL-6514-03 Version Date Document Version HistoryObjectives Section Title Description OrganizationRelated Documentation Preface Related Documentation OL-6514-04 PA-POS-1OC3 Overview PA-POS-1OC3 OverviewSONET/SDH Overview SDH EquivalentFeatures Interface Specifications OC-3 Optical Fiber SpecificationsNetwork Management Support Using Statistics to Estimate Link Loss and Power Budget LEDsEncapsulation Method Support LED Label Color State FunctionCables and Connectors RCVPort Adapter Slot Locations on the Supported Platforms Cisco 7200 VXR Routers Slot NumberingCisco 7201 Router Slot Numbering Cisco 7200 Series VXRCisco 7301 Router Slot Numbering Cisco 7304 PCI Port Adapter Carrier Card Slot NumberingCisco 7401ASR Router Slot Numbering Module Slots on the Cisco 7304 RouterCisco 7500 Series Routers with VIP Slot Numbering 10 VIP Slot LocationsCisco 7505 Router Slot Numbering RSPCisco 7507 Router Slot Numbering VIP interface-slot RSP-slotCisco 7513 Router Slot Numbering 6 8 10Cisco 7603 Router Slot Numbering SUPERVISOR2Cisco 7606 Router Slot Numbering Cisco 7609 Router Slot Numbering FAN StatusCisco 7613 Router Slot Numbering Identifying Interface Addresses Platform Interface Address Format Numbers SyntaxCisco 7301 Router Interface Addresses Cisco 7200 VXR Routers Interface AddressesCisco 7201 Router Interface Addresses Cisco 7401ASR Router Interface Addresses Cisco 7500 Series Routers VIP Interface AddressesCisco 7600 Series Routers FlexWAN Module Interface Addresses OL-6514-04 Preparing for Installation Required Tools and EquipmentPlatform Recommended Minimum Cisco IOS Release Software and Hardware RequirementsCisco 7200 VXR Routers Checking Hardware and Software Compatibility Safety Guidelines Safety WarningsAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Guarde Estas Instrucciones GEM Disse Anvisninger OL-6514-04 Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageLaser Safety FCC Class a ComplianceOL-6514-04 Removing and Installing the PA-POS-1OC3 Handling Port AdaptersOnline Insertion and Removal Handling a Port AdapterOIR Functional Description Port Adapter Removal and Installation Step Cisco 7201 Router-Removing and Installing a Port Adapter CiscoCisco 7301 Router-Removing and Installing a Port Adapter OL-6514-04 CC-PA Cisco 7401ASR Router-Removing and Installing a Port Adapter With the screw removed, grasp Screw Connecting PA-POS-1OC3 Interface Cables TX RXRemoving the SFP Optics Module Replacing the SFP Optics ModuleHandling the SFP Optics Module Installing the SFP Optics Module Verifying the SFP Optics Module Installation Inserting an SFP Optics ModulePage OL-6514-04 Configuring the PA-POS-1OC3 Using the Exec Command InterpreterConfiguring the Interfaces Parameter Configuration Commands Default ValuePlatform Command Example Shutting Down an InterfaceSlot/port-adapter/port Show interfaces pos, followed by Performing a Basic Configuration Show interfaces pos followed byInterface pos, followed by Customizing the Configuration Setting the Source of the Transmit Clock Setting the MTU SizeConfiguring Framing Configuring Cyclic Redundancy Checks Configuring Sonet Payload ScramblingConfiguring APS Basic APS ConfigurationCommand Function Example Checking the ConfigurationUsing show Commands to Verify the New Interface Status Show controllers Using the show version or show hardware Commands Cisco 7201 Router-Example Output of the show version Command Router#show version Using the show diag Command Port adapter is analyzedCisco 7201 Router-Example Output of the show diag Command Router#show diag Using the show interfaces Command Router# show interfaces pos 4/0 PE3#sh int pos4/1Router# show interfaces Using the ping Command to Verify Network Connectivity Router# ping 10.0.0.10 ReturnConfiguring an Interface for Line Loopback Using loopback CommandsConfiguring an Interface for Internal Loopback Push Mode Description PA-POS-1OC3 Error Messages PA-POS-1OC3 Statistics CountersMaking a Back-to-Back Connection First routerConfiguring the PA-POS-1OC3 Making a Back-to-Back Connection

PA-POS-1OC3, PA-POS-2OC3 specifications

Cisco Systems has long been at the forefront of networking technology, providing solutions that empower organizations to enhance their connectivity and communication capabilities. Among its impressive lineup, the PA-POS-2OC3 and PA-POS-1OC3 modules stand out as significant components designed to optimize performance in service provider and enterprise environments.

The PA-POS-2OC3 and PA-POS-1OC3 modules are designed for use with the Cisco 7600 Series routers and are tailored for Packet Over SONET (POS) transport. Supporting the OC-3 speed of 155.52 Mbps, these modules provide reliable high-speed connectivity, enabling organizations to efficiently manage data traffic and ensure rapid data transfer across their networks. The PA-POS-2OC3 offers dual OC-3 capabilities, allowing for higher aggregate bandwidth and redundancy options, making it common in demanding network environments.

One of the main features of the PA-POS-2OC3 and PA-POS-1OC3 is their enhanced support for advanced networking protocols, including MPLS (Multiprotocol Label Switching). MPLS facilitates efficient data routing and improves bandwidth utilization by enabling multiple types of traffic to be consolidated over a single network. This is crucial for organizations looking to deploy services like VoIP, video conferencing, and other bandwidth-intensive applications.

The modules also offer robust error correction and monitoring capabilities, which are essential for maintaining service quality in mission-critical applications. Administrators can monitor performance and diagnose issues in real-time, enabling swift responses to potential concerns that could disrupt service.

Moreover, the PA-POS-2OC3 and PA-POS-1OC3 are designed with features that support enterprise-grade security and scalability. This is particularly beneficial for organizations expecting growth or requiring enhanced protection for sensitive data as it traverses the network.

In summary, Cisco's PA-POS-2OC3 and PA-POS-1OC3 modules represent essential building blocks for high-speed networking solutions. Their support for OC-3 connectivity, advanced routing protocols, and robust monitoring capabilities make them ideal for both service providers and enterprises. Through increased scalability, improved bandwidth management, and enhanced security, these modules allow organizations to adapt to the ever-evolving landscape of data communications effectively. With Cisco at the helm, businesses can trust in a networking solution that not only meets current demands but is also primed for future growth.
Top Page Image Contents