Cisco Systems 512, 612 manual Installing Adapters

Page 71

Chapter 4 Installing Hardware Options

Installing Adapters

Installing Adapters

This section provides general information about the system board, riser card, adapters, and PCI-X slot configuration specifications. Use these instructions to install any full-height three-quarter-length PCI-X adapter card.

Note The MPEG decoder adapter is supported in ACNS software only. The inline network adapter is supported in WAAS 4.0.7 and later software only.

Before you install adapters, review the following information:

The adapter slots are on the riser card assembly. You must first remove the riser card assembly to access the adapter slots. (See Figure 4-2.)

The device has two Peripheral Component Interconnect-Extended (PCI-X) adapter slots:

PCI-X slot 1 is for one full-height three-quarter-length adapter.

PCI-X slot 2 is for one low-profile half-length adapter; however, it is not used in this device.

You must install supported adapters in PCI-X slot 1. (This slot is labeled “Slot 1” on the back of the device.)

Documentation is included with the adapter. Follow the instructions in the adapter documentation in addition to the instructions in this chapter.

Caution When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For details on handling these devices, see the “Protecting Against Electrostatic Discharge” section on page 2-6.

Note The illustrations in this document might differ slightly from your hardware.

To install an adapter, follow these steps:

Step 1 Review the safety information in the “Safety Guidelines” section on page 2-4. Step 2 Power down the device and peripheral devices.

 

 

Cisco Wide Area Application Engine 512 and 612 Hardware Installation Guide

 

 

 

 

 

 

OL-9137-02

 

 

4-3

 

 

 

Image 71
Contents Americas Headquarters Page Iii N T E N T SGeneral Precautions Completing the Installation OL-9137-02 Vii PurposeViii AudienceOrganization Conventions Installing Hardware OptionsScreen examples use the following conventions Related Documentation Xii Xiii Obtaining DocumentationCisco.com Product Documentation DVDXiv Documentation FeedbackOrdering Documentation Cisco Product Security Overview Xvi Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Xvii Submitting a Service RequestCisco Technical Support & Documentation Website Xviii Definitions of Service Request SeverityXix Obtaining Additional Publications and InformationOL-9137-02 Introduction Introducing the Cisco Wide Area Application Engine1shows the WAE-512 and -2shows the WAE-612 3shows the WAE rear view Waas Software Description Software Functional DescriptionAcns Software Description Wafs Software Description Hardware FeaturesFront Panel Control Buttons LED IndicatorsLED Indicator Color State Description WAE-512 and WAE-612 Back Panel Connectors and Receptacles Input/Output Ports and ConnectorsEthernet Port Connector Serial Port Connector Video Port Connectors Form and Function Inline Network Adapter Description11 Inline Network Adapter Ports and LED Indicators Inline Network Adapter Cabling Requirements OL-9137-02 Cable Requirements for WAE Connections Using Fast Ethernet OL-9137-02 Router a WAE1 WAE2 15 Cabling Between Two Inline WAEs OL-9137-02 Safety Warnings Preparing to Install the Cisco Wide Area Application EngineSafety Warnings OL-9137-02 General Precautions Safety GuidelinesOL-9137-02 Protecting Against Electrostatic Discharge Rack Installation Safety GuidelinesOL-9137-02 OL-9137-02 Installing the Cisco Wide Area Application Engine Tools and Parts Required Installing the Cisco Wide Area Application EngineOrientation for 19-inch rack Installing the Chassis in a Two-Post RackInstalling the Chassis in the Rack Installing the Chassis in a Four-Post RackRack-Mount Installation Kit Installing the Cisco Wide Area Application Engine Release tab for the rail-adjustment bracket Latch tab 134405 Captive thumbscrews Shipping brackets Removing the Shipping Bracket 10 Securing the Chassis for Transporting in the Rack 11 Attaching the Slide Rails and Chassis Using M6 Screws Installing the Chassis on a TabletopConnecting Cables 12 WAE-512 and WAE-612 Back Panel Connectors and Receptacles Removing or Replacing a Cisco Wide Area Application Engine Connecting Power and Booting the SystemChecking the LEDs OL-9137-02 Removing the Cover and Bezel Installing Hardware OptionsPress the cover release button. See Figure Installing Adapters Removing the Riser Card Assembly Installing the Adapter in the Riser Card Assembly Installing DIMMs Dimm To install a DIMM, follow these steps Working with Hard Disk Drives Safety Guidelines section on Installing Sata Hard Disk DrivesInstalling an Sata Hard Disk in the WAE-512-Disk00 is Shown Installing an SAS Hard Disk Drive Installing a SAS Hard Disk in the WAE-612-Disk01 is Shown Installing the Cover Completing the InstallationInstalling Hardware Options Completing the Installation OL-9137-02 Appliance Specifications Technical SpecificationsSpecification Description Specification Description Adapter Specifications PDIF4 Table A-4 Inline Network Adapter Specifications Checking the Basics Troubleshooting the System HardwareChecking Connections and Switches OL-9137-02 OL-9137-02 Maintaining Your Site Environment Maintaining the Cisco Wide Area Application EngineTemperature Dust and Particles HumidityAltitude Electromagnetic and Radio Frequency Interference CorrosionElectrostatic Discharge Magnetism Power Source Interruptions Line Conditioners Using Power Protection DevicesUninterruptible Power Supplies Surge ProtectorsOL-9137-02 IN-1 D EIN-2 ESDIN-3 IN-4 IN-5 RFIIN-6 WAE

512, 612 specifications

Cisco Systems has been at the forefront of networking and communication technologies for decades, and its innovations consistently set industry standards. Among its extensive product portfolio, the Cisco 612,512 stands out as a pivotal piece of hardware designed to enhance connectivity and performance in various environments.

The Cisco 612,512 is recognized for its solid architecture and robust performance tailored to meet the demands of modern enterprises. One of its main features is its high throughput, which allows it to handle substantial data traffic with minimal latency. This capability is vital for organizations needing to support numerous applications and services that require quick data access and processing.

In terms of technologies, one of the key advancements integrated into the Cisco 612,512 is its support for advanced routing protocols. With features like OSPF (Open Shortest Path First) and BGP (Border Gateway Protocol), the device can efficiently manage traffic across both local and wide-area networks. This ensures that data packets follow the most efficient paths, reducing congestion and improving overall network responsiveness.

Another significant characteristic of the Cisco 612,512 is its scalability. Organizations of varying sizes can deploy it to meet their specific connectivity needs. Whether it's a small business looking to expand its network or a large corporation managing a global infrastructure, the Cisco 612,512 can adapt accordingly, offering modular options that allow for hardware and software upgrades as requirements evolve.

Security remains a primary concern in networking, and the Cisco 612,512 does not fall short in this area. Equipped with state-of-the-art encryption and authentication protocols, it provides a secure environment for data transmission. Additionally, the device incorporates advanced threat detection mechanisms to identify and mitigate potential security breaches, ensuring that sensitive information remains protected.

Moreover, the Cisco 612,512 features comprehensive management tools that make network monitoring and configuration straightforward. With its user-friendly interface and detailed analytics, IT administrators can easily oversee network performance, troubleshoot issues, and implement necessary changes without extensive downtime.

In summary, the Cisco Systems 612,512 is a powerful networking solution that balances performance, scalability, and security. Its advanced routing capabilities, robust feature set, and user-friendly management tools make it an ideal choice for organizations seeking to enhance their connectivity infrastructure while ensuring reliability and safety in their communications. As businesses continue to evolve and embrace digital transformation, devices like the Cisco 612,512 will undoubtedly play a vital role in their success.