Cisco Systems CISCO1841-HSEC/K9-RF Yourname con0 is now available Press Return to get started

Page 67

Chapter 7 Power-Up Procedures for Cisco 1800 Series Routers (Modular)

Powering Up Cisco 1800 Series Routers

If you encounter problems when you power up the router, see Chapter 8, “Troubleshooting Cisco 1800 Series Routers (Modular).” For information about the ROM monitor and the bootstrap program, see the “Using the ROM Monitor” section of the Cisco 1800 Series Router Software Configuration. For information about the configuration register, see the“Changing the Configuration Register Settings” section of Cisco 1800 Series Router Software Configuration.

Note To view the boot sequence through a terminal session, you must have a console connection to the Cisco router before the router powers up.

To power up the router, perform the following steps:

Step 1 Make sure that your PC is powered up and connected as described in the “Checklist for Power Up” section on page 7-2.

Step 2 Move the power switch to the ON position.

The following indications appear:

•The green SYS PWR LED on the front of the chassis comes on.

•The fan operates.

The LEDs on the chassis come on (although not necessarily at the same time), and some LEDs may go off again. The actual LED activity depends on your installation.

If you encounter problems when you power up the router, see “Troubleshooting Cisco 1800 Series Routers (Modular)”

Startup messages appear in your terminal emulation program window.

Caution Do not press any keys on the keyboard until the messages stop. Any keys pressed during this time are interpreted as the first command typed when the messages stop, which might cause the router to power off and start over. It takes a few minutes for the messages to stop.

The startup messages vary, depending on the software installed on your router.

•If the startup messages end with the following lines, you know that the Cisco Router and Security Device Manager (SDM) software is installed on the router.

yourname con0 is now available

Press RETURN to get started!

For instructions on configuring your router by using SDM, see Cisco Router and Security Device Manager (SDM) Quick Start Guide.

Note Because SDM is installed on your router by default, we recommend using SDM to perform the initial configuration.

•If the startup messages end with the following lines, the router is ready for initial configuration using the setup facility (system configuration dialog) or the command-line interface (CLI). Enter yes to continue with the setup facility; enter no to continue with the CLI.

Cisco 1800 Series Routers (Modular) Hardware Installation Guide

 

OL-5876-03

7-3

 

 

 

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Text Part Number OL-5876-03 Americas HeadquartersCopyright 2005-2008 Cisco Systems, Inc. All rights reserved Interfaces on the Cisco 1861 Integrated Services Router Site Log LED Indicators Modular Objectives Organization AudienceTitle Description Conventions Safety WarningsConvention Description Bewaar Deze Instructies Avvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger OL-5876-03 Related Documentation Duration of Hardware Warranty Cisco One-Year Limited Hardware Warranty TermsTo Receive a Return Materials Authorization RMA Number Replacement, Repair, or Refund Policy for HardwareSearching for Cisco Documents OL-5876-03 Overview of Cisco 1800 Series Routers Modular Product Serial Number Location, Hardware FeaturesInterfaces Product Serial Number LocationCisco Product Identification Tool Interfaces on the Cisco 1841 Router Interfaces on the Cisco 1861 Integrated Services RouterDescription Label Memory Removable and Interchangeable ModulesModel CompactFlash Memory Interface Cards AIMs Description Specification LED IndicatorsColor Description Location Real-Time Clock Chassis VentilationChassis Security Chassis ViewsSlot Number Slot Type Interface NumberingExample Interface Numbering on the 1861 Integrated Services Router Regulatory Compliance SpecificationsOL-5876-03 Safety Recommendations Safety with Electricity General Site Requirements Power Supply ConsiderationsPreventing Electrostatic Discharge Damage Site Configuration Installation ChecklistSite Environment Task Verified by Date Site LogItems in the Box for the Cisco 1841 Router Inspecting the RouterAssembly hardware screws OL-5876-03 Plug-In Components Internal ComponentsInterfaces on the Cisco 1861 Integrated Services Router Setting the Chassis on a Desktop Setting Up the Chassis1shows the brackets Attaching Rack-Mount BracketsMounting the Chassis in a Rack Typical Installing the Router in a RackChassis Grounding Wall-Mounting the ChassisWall-Mounting the Cisco 1841 Router Wall Router Mounting screws Wall-Mounting the Cisco 1861 Integrated Services Router Wall-Mount Bracket for Power Supply Rack-Mounting the Cisco 1861 Integrated Services RouterBrackets for Rack-Mounting Power Supply Installing the Chassis Ground Connection 11 Chassis Ground Connection on the Cisco 1841 Router 12 Attaching the Ground Wire to the Chassis OL-5876-03 Console Port Connections Console and Auxiliary Port ConsiderationsAuxiliary Port Connections Preparing to Connect to a NetworkEthernet Connections Serial DTE or DCE Devices Configuring Serial ConnectionsSignaling Standards Supported Serial ConnectionsAsynchronous/Synchronous Serial Module Baud Rates Distance LimitationsDistance for CSU/DSU Connections Isdn BRI ConnectionsLow-Capacitance Cable OL-5876-03 Series Routers Modular Power ConnectionsPorts and Cabling Connecting WAN and LAN CablesPort Type, Color Connected to Cable Connection Procedures and Precautions Connecting to a Console Terminal or ModemConnecting to the Auxiliary Port Connecting to the Console PortConnecting a Modem to the Router OL-5876-03 Routers Modular Powering Up Cisco 1800 Series RoutersPower-Up Procedure Checklist for Power UpYourname con0 is now available Press Return to get started Color Status Verifying the LED Indicators on the 1841 RouterInitial Configuration of the Router Verifying the Hardware ConfigurationInitial Configuration Completing the Configuration Verifying the Initial ConfigurationCisco Router and Security Device Manager Description Benefits Powering up the Cisco 1861 Integrated Services RouterDescription Benefits Problem Solving Troubleshooting Cisco 1800 Series Routers ModularFault Indications Troubleshooting the Power and Cooling SystemsNormal Indications Environmental Reporting Features Troubleshooting Cables, Connections, and Interface CardsReading LEDs FDX System MessagesMore Troubleshooting Help Recovering a Lost PasswordExplanantion Installing WICs, VWICs, and HWICs Cisco Interface Cards Installation GuideRelated Product Documentation Card guides Interface card Page OL-5876-03 10-1 Replacing CompactFlash Memory Cards10-2 Using the Compact Flash GuardInstalling a CompactFlash Memory Card Removing a CompactFlash Memory Card10-3 10-4 11-1 Opening the Chassis Modules Internal to the Cisco 1841 Router11-2 Removing the Chassis Screw 11-311-4 Locating Modules11-5 Installing a Sodimm11-6 Installing an AIM11-7 Accessory Kit to UseInstallation Procedure Cisco Part Number TypeLocation of Metal Standoff Attachment Locations 11-8Plastic Standoff Orientation 11-911-10 Connecting the AIM to the System BoardApplying the AIM Label Closing the Chassis11-11 11 Closing the Chassis 11-12IN-1 ACT LEDIN-2

CISCO1841-HSEC/K9-RF specifications

The Cisco Systems CISCO1841-HSEC/K9-RF is a versatile and robust router designed to meet the demands of small to medium-sized businesses and branch offices. This model is part of the Cisco 1800 Series Integrated Services Routers, which are known for their performance, security features, and scalability, making them ideal for organizations seeking to enhance their network infrastructure.

One of the main features of the CISCO1841-HSEC/K9 is its modular architecture. This design allows businesses to customize and expand their networks according to changing needs by adding various modules and interfaces. The router supports multiple WAN interfaces, which include serial, Ethernet, and DSL, providing flexible connectivity options to accommodate various networking scenarios.

The CISCO1841-HSEC/K9 also boasts an integrated security architecture. This router is equipped with advanced security features, including firewall capabilities, VPN support, and intrusion prevention systems. These technologies ensure that data is protected while being transmitted across the network. The built-in security features help organizations safeguard sensitive information against potential threats and cyberattacks.

In terms of performance, the CISCO1841-HSEC/K9 is powered by a high-speed processor and dynamic routing capabilities, which allow it to efficiently handle high volumes of traffic without compromising performance. The router supports various routing protocols, including EIGRP, OSPF, and BGP, facilitating seamless data flow and efficient route management.

Another noteworthy characteristic of the CISCO1841-HSEC/K9 is its support for voice and video services. This capability enables businesses to deploy unified communications applications, such as VoIP and video conferencing, enhancing collaboration among team members and improving overall productivity.

Moreover, the router is designed for easy management and monitoring. Cisco’s IOS software provides a user-friendly interface, allowing network administrators to configure, operate, and troubleshoot the network with ease. The router also supports Cisco’s Smart Install feature for simplified deployment and management.

In summary, the Cisco Systems CISCO1841-HSEC/K9-RF is a powerful and adaptable router that combines security, flexibility, and performance. Its modular design, robust security features, support for various routing protocols, and capabilities for multimedia applications make it a compelling choice for businesses looking to enhance their network infrastructure while addressing current and future demands.
Top Page Image Contents