Cisco Systems CRS-1 manual This section contains the following procedures

Page 32

Chapter 2 Converting to an Integrated Switch System

How to Convert from the Cisco Catalyst 65xx Switch to the Integrated Switch System for Single-FCC Multishelf and

Two-FCC Multishelf Systems

How to Convert from the Cisco Catalyst 65xx Switch to the Integrated Switch System for Single-FCC Multishelf and Two-FCC Multishelf Systems

This section contains the following procedures:

•Validating the 22-port SCGE Cards (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-4

•Connecting the 22-port SCGE to an Active Cat6K (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-5

•Transferring the Backup Cisco Catalyst 65xx Switch Gigabit Ethernet Connections to a Standby 22-port SCGE (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-6

•Performing a Failover to a Standby 22-port SCGE (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-7

•Connecting the 22-port SCGEs into a Full Mesh (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-8

•Transferring an Active Cat6K Gigabit Ethernet Connections to the Active 22-port SCGE (Single-FCC Multishelf and Two-FCC Multishelf Systems), page 2-9

Validating the 22-port SCGE Cards (Single-FCC Multishelf and Two-FCC Multishelf Systems)

To validate the 22-port SCGE cards, perform the following steps:

Step 1 Insert the 22-port SCGE card into the standby slot (SC-GE-2) of FCC. Remove the 2-port card that is already installed.

Step 2 Use the show platform command in EXEC mode or administration EXEC mode to verify that the

22-port SCGE card is in the IOS XR RUN state, as shown in the following example:

RP/0/RP0/CPU0:router(admin)# show platform

NodeTypePLIMStateConfig State

-----------------------------------------------------------------------------

0/3/SP

MSC(SP)

N/A

IOS XR RUN

PWR,NSHUT,MON

0/3/CPU0

MSC

Jacket Card

IOS XR RUN

PWR,NSHUT,MON

0/3/2

MSC(SPA)

8X1GE

OK

PWR,NSHUT,MON

0/3/4

MSC(SPA)

8X1GE

OK

PWR,NSHUT,MON

0/RP0/CPU0

RP(Active)

N/A

IOS XR RUN

PWR,NSHUT,MON

0/RP1/CPU0

RP(Standby)

N/A

IOS XR RUN

PWR,NSHUT,MON

0/SM1/SP

FC/M(SP)

N/A

IOS XR RUN

PWR,NSHUT,MON

F0/SM0/SP

FCC-SFC(SP)

N/A

IOS XR RUN

PWR,NSHUT,MON

F0/SC0/CPU0

FCC-SC(Active)

N/A

IOS XR RUN

PWR,NSHUT,MON

F0/SC1/CPU0

FCC-SC(Standby)

N/A

IOS XR RUN

PWR,NSHUT,MON

Step 3 Use the show redundancy command in EXEC mode to verify that the standby node is ready.

RP/0/RP0/CPU0:router# show redundancy

Redundancy information for node 0/RP0/CPU0:

==========================================

Node 0/RP0/CPU0 is in ACTIVE role

Cisco CRS-1 Carrier Routing System Multishelf System Upgrade and Conversion Guide

2-4

OL-12571-01

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Americas Headquarters Page N T E N T S Index Cisco.com Changes to This DocumentObtaining Documentation Product Documentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Reporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteObtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Preface Obtaining Additional Publications and Information Contents Prerequisites for Upgrading to a Multishelf SystemRestrictions for Upgrading to a Multishelf System Multishelf System section onHow to Upgrade to a Multishelf System Information About Upgrading to a Multishelf SystemUpgrading the Fabric Cards and Adding an FCC NoneApply power to the FCC Places the router in administration Exec modeAll commands listed in this procedure should be Places the router in administration configuration modeConfigures the FCC identified by the serial number as an Configures a plane to operate in an FCC slotEnter this command sequence for each of the eight To 7 you want to configureDo command prefix allows the Exec mode show Command to execute in administration configurationExamine Replace the planeNumber parameter with the numberModifies the target configuration to bring up the specified Which is now configured to use the FCC-SFCDisplays the administrative and operational status of all Displays the status of the Rack 0 fabric slot specified byAdding an LCC to a Multishelf System What to Do NextConfigures the additional LCC as Rack 1 in the multishelf Modifies the target configuration to change the RackConfiguration to installation mode For racks in installation modeDisplaying Chassis Serial Numbers Example Adding a Fabric Card Chassis Example Power is applied to the FCC at this time FC/S card is replaced with an FC/M card at this point Fabric cable is attached to the FC/M card at this pointApply power, attach cables, and check cable LEDs Adding an LCC to a Multishelf System ExampleNormal Related Documents Where to Go NextAdditional References Related Documentation for the Catalyst 6509 Switch Technical AssistanceConverting to an Integrated Switch System Prerequisites for the Integrated Switch System Cisco CRS-1 Multishelf Integrated Switch Solution Naming ConventionsThis section contains the following procedures Repeat to for the remaining FCC Partner node F0/SC1/CPU0 is in Standby roleShow controllers switch inter-rack stp location node-id Redundancy switchover location node-id Repeat to for the other fabric chassis on a two-FCC MC MST1 Validating the 22-port Scge Cards Four-FCC Multishelf System OL-12571-01 OL-12571-01 For Cist Redundancy switchover location node-id Show controllers switch inter-rack udld all location node-id Show controllers switch inter-rack udld all location node-id Admin configure command 1-5,1-10 Installation documents LEDsSerial number configuration Fabric card, single-chassis systemIN-2
Related manuals
Manual 6 pages 31.8 Kb Manual 46 pages 23.29 Kb Manual 54 pages 8.79 Kb

CRS-1 specifications

Cisco Systems' Carrier Routing System (CRS-1) is a cutting-edge, high-capacity router designed to meet the demands of service providers and large enterprises. Introduced in the early 2000s, the CRS-1 represents a significant leap forward in routing technology, offering unparalleled performance, scalability, and reliability.

One of the primary features of the CRS-1 is its exceptional scalability. The system is built on a modular architecture that allows for easy upgrades and expansions. This enables service providers to start with a configuration that suits their immediate needs while having the flexibility to expand as traffic demands grow. The CRS-1 supports a wide range of line cards, enabling data, voice, and video to be managed on a single platform, which simplifies network management and reduces operating costs.

The CRS-1 leverages advanced technologies that enable it to deliver impressive performance. With the ability to handle up to 92 terabits per second of throughput, the router is capable of supporting a vast number of connections, making it well-suited for large-scale service providers and data centers. This level of performance is powered by Cisco’s proprietary silicon technology, which optimizes the packet forwarding process and enhances overall efficiency.

Another key characteristic of the CRS-1 is its strong focus on reliability and redundancy. The system is designed with high availability in mind, ensuring that it can continue to operate seamlessly even in the event of hardware failures. Redundant components, such as power supplies and route processors, allow the CRS-1 to maintain its performance and uptime, a critical requirement for mission-critical network operations.

Additionally, the CRS-1 supports a wide variety of protocols and technologies, including Internet Protocol (IP), Multiprotocol Label Switching (MPLS), and various service provider features. This versatility makes it a compelling choice for organizations looking to implement advanced networking capabilities, such as Quality of Service (QoS) and traffic engineering.

In summary, the Cisco Systems CRS-1 stands out as a formidable solution for modern routing needs. Its modular design, exceptional scalability, robust performance, reliability, and support for multiple protocols and services make it an ideal choice for service providers and enterprises seeking to future-proof their networks. As the demand for bandwidth continues to surge, the CRS-1 remains a pivotal component in the evolution of networking infrastructure.
Top Page Image Contents