Cisco Systems CRS-1 manual Configures the FCC identified by the serial number as an, Fabric planes

Page 16

Chapter 1 Upgrading to a Multishelf System

How to Upgrade to a Multishelf System

 

Command or Action

Purpose

Step 4

 

 

dsc serial serialNumber rack Frack

Configures the FCC identified by the serial number as an

 

 

FCC rack within the multishelf system.

 

Example:

• Replace serialNumber with the serial number of the

 

RP/0/RP1/CPU0:router(admin-config)# dsc serial

FCC.

 

TBC0820052000000 rack F0

• Replace rack with the FCC number as it appears in the

 

 

 

 

fabric cabling plan, which is described in Cisco CRS-1

 

 

Carrier Routing System Multishelf System

 

 

Interconnection and Cabling Guide.

 

 

• If you are configuring the system from a remote

 

 

location, you can use a command to display the serial

 

 

number. For more information, see Cisco IOS XR

 

 

Getting Started Guide.

Step 5

 

 

controllers fabric plane planeNumber

Configures a plane to operate in an FCC slot.

 

oim count 1

• Enter this command sequence for each of the eight

 

oim instance 0 location Frack/slot/FM

 

 

fabric planes.

 

Example:

• Replace planeNumber with the number of the plane (0

 

to 7) you want to configure.

 

RP/0/RP1/CPU0:router(admin-config)# controllers

 

fabric plane 0

• Replace rack with the FCC rack number assigned to the

 

RP/0/RP1/CPU0:router(admin-config)# oim count 1

 

FCC that hosts the plane.

 

RP/0/RP1/CPU0:router(admin-config)# oim

 

 

 

instance 0 location F0/SM9/FM

• Replace slot with the FCC slot number that supports the

 

 

 

 

fabric plane you are configuring. Valid slot numbers are

 

 

SM0 to SM23.

 

 

• The plane numbers and slot numbers are determined by

 

 

the hardware installation and cabling. The software

 

 

configuration must match the hardware configuration.

 

 

For more information, see Cisco CRS-1 Carrier

 

 

Routing System Multishelf System Interconnection and

 

 

Cabling Guide.

 

 

• Enter this command once for each of the eight planes.

 

 

Note These configuration commands are ignored when

 

 

the FC/S cards are installed.

Step 6

 

 

commit

Commits the target configuration to the router running

 

 

configuration.

 

Example:

 

 

RP/0/RP1/CPU0:router(admin-config)# commit

 

Step 7

 

 

end

Changes the mode from administration configuration mode

 

 

to administration EXEC mode.

 

Example:

 

 

RP/0/RP1/CPU0:router(admin-config)# end

 

Step 8

 

 

Apply power to the FCCs.

Starts the FCCs.

 

 

 

Cisco CRS-1 Carrier Routing System Multishelf System Upgrade and Conversion Guide

1-6

OL-12571-01

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Americas Headquarters Page N T E N T S Index Obtaining Documentation Changes to This DocumentCisco.com Cisco Product Security Overview Documentation FeedbackProduct Documentation DVD Ordering Documentation Reporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteDefinitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Preface Obtaining Additional Publications and Information Contents Prerequisites for Upgrading to a Multishelf SystemRestrictions for Upgrading to a Multishelf System Multishelf System section onHow to Upgrade to a Multishelf System Information About Upgrading to a Multishelf SystemUpgrading the Fabric Cards and Adding an FCC NoneApply power to the FCC Places the router in administration Exec modeAll commands listed in this procedure should be Places the router in administration configuration modeConfigures the FCC identified by the serial number as an Configures a plane to operate in an FCC slotEnter this command sequence for each of the eight To 7 you want to configureDo command prefix allows the Exec mode show Command to execute in administration configurationExamine Replace the planeNumber parameter with the numberModifies the target configuration to bring up the specified Which is now configured to use the FCC-SFCDisplays the administrative and operational status of all Displays the status of the Rack 0 fabric slot specified byAdding an LCC to a Multishelf System What to Do NextConfigures the additional LCC as Rack 1 in the multishelf Modifies the target configuration to change the RackConfiguration to installation mode For racks in installation modeDisplaying Chassis Serial Numbers Example Adding a Fabric Card Chassis Example Power is applied to the FCC at this time FC/S card is replaced with an FC/M card at this point Fabric cable is attached to the FC/M card at this pointApply power, attach cables, and check cable LEDs Adding an LCC to a Multishelf System ExampleNormal Additional References Where to Go NextRelated Documents Related Documentation for the Catalyst 6509 Switch Technical AssistanceConverting to an Integrated Switch System Prerequisites for the Integrated Switch System Cisco CRS-1 Multishelf Integrated Switch Solution Naming ConventionsThis section contains the following procedures Repeat to for the remaining FCC Partner node F0/SC1/CPU0 is in Standby roleShow controllers switch inter-rack stp location node-id Redundancy switchover location node-id Repeat to for the other fabric chassis on a two-FCC MC MST1 Validating the 22-port Scge Cards Four-FCC Multishelf System OL-12571-01 OL-12571-01 For Cist Redundancy switchover location node-id Show controllers switch inter-rack udld all location node-id Show controllers switch inter-rack udld all location node-id Admin configure command 1-5,1-10 Installation documents LEDsSerial number configuration Fabric card, single-chassis systemIN-2
Related manuals
Manual 6 pages 31.8 Kb Manual 46 pages 23.29 Kb Manual 54 pages 8.79 Kb

CRS-1 specifications

Cisco Systems' Carrier Routing System (CRS-1) is a cutting-edge, high-capacity router designed to meet the demands of service providers and large enterprises. Introduced in the early 2000s, the CRS-1 represents a significant leap forward in routing technology, offering unparalleled performance, scalability, and reliability.

One of the primary features of the CRS-1 is its exceptional scalability. The system is built on a modular architecture that allows for easy upgrades and expansions. This enables service providers to start with a configuration that suits their immediate needs while having the flexibility to expand as traffic demands grow. The CRS-1 supports a wide range of line cards, enabling data, voice, and video to be managed on a single platform, which simplifies network management and reduces operating costs.

The CRS-1 leverages advanced technologies that enable it to deliver impressive performance. With the ability to handle up to 92 terabits per second of throughput, the router is capable of supporting a vast number of connections, making it well-suited for large-scale service providers and data centers. This level of performance is powered by Cisco’s proprietary silicon technology, which optimizes the packet forwarding process and enhances overall efficiency.

Another key characteristic of the CRS-1 is its strong focus on reliability and redundancy. The system is designed with high availability in mind, ensuring that it can continue to operate seamlessly even in the event of hardware failures. Redundant components, such as power supplies and route processors, allow the CRS-1 to maintain its performance and uptime, a critical requirement for mission-critical network operations.

Additionally, the CRS-1 supports a wide variety of protocols and technologies, including Internet Protocol (IP), Multiprotocol Label Switching (MPLS), and various service provider features. This versatility makes it a compelling choice for organizations looking to implement advanced networking capabilities, such as Quality of Service (QoS) and traffic engineering.

In summary, the Cisco Systems CRS-1 stands out as a formidable solution for modern routing needs. Its modular design, exceptional scalability, robust performance, reliability, and support for multiple protocols and services make it an ideal choice for service providers and enterprises seeking to future-proof their networks. As the demand for bandwidth continues to surge, the CRS-1 remains a pivotal component in the evolution of networking infrastructure.
Top Page Image Contents