Cisco Systems OL-31454-01 manual Preparing for Network Connections, Auxiliary Port Connections

Page 34

Chapter 2 Preparing for Router Installation

Network Cabling Specifications

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The console port does not support hardware flow control. For detailed information about installing a console terminal, see the “Connecting to a Console Terminal or Modem” section on page 3-17.

For cable and port pinouts, see Cisco Modular Access Router Cable Specifications.

USB Serial Console Port

The USB serial console port connects directly to the USB connector of a PC using a USB Type A to 5-pin mini USB Type-B cable. The USB Console supports full speed (12Mb/s) operation. The console port does not support hardware flow control.

Note Always use shielded USB cables with a properly terminated shield.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The console port does not support mode control. For detailed information about installing a console terminal, see the “Connecting to a Console Terminal or Modem” section on page 3-17.

For operation with Microsoft Windows, the Cisco Windows USB Console Driver must be installed on every PC connected to the console port. If the driver is not installed, prompts guide you through a simple installation process. For detailed information about installing the Cisco Windows USB Console Driver see “Installing the Cisco Microsoft Windows USB Device Driver” section on page 3-21.

The Cisco Windows USB Console Driver allows plugging and unplugging the USB cable from the console port without affecting Windows HyperTerminal operations. No special drivers are needed for Mac OS X or Linux.

Only one console port can be active at a time. When a cable is plugged into the USB console port the RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port, the RJ-45 port becomes active.

Baud rates for the USB console port are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200 bps.

Note 4-pin mini USB Type-B connectors are easily confused with 5-pin mini USB Type-B connectors. They are not compatible. Only the 5-pin mini USB Type-B can be used.

Auxiliary Port Connections

The router has an EIA/TIA-232 asynchronous serial auxiliary port (RJ-45) that supports flow control. Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the cable.

Preparing for Network Connections

When setting up your router, consider distance limitations and potential electromagnetic interference (EMI) as defined by the applicable local and international regulations.

Network connection considerations are provided for several types of network interfaces and are described in the following sections:

•Ethernet Connections, page 2-7

•Serial Connections, page 2-7

Cisco 2010 Connected Grid Router Hardware Installation Guide

2-6

OL-31454-01

 

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Cisco 2010 Connected Grid Router Hardware Installation Guide Page N T E N T S Attaching Rack-Mount Brackets to Cisco CGR 2010 Routers Configuring the Router Verifying the Initial Configuration Objectives AudienceChapter Title Description OrganizationConventions Convention IndicationBewaar Deze Instructies Avvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Xiii Xiv Obtaining Documentation and Submitting a Service Request Searching for Cisco DocumentsXvi Chassis Views A P T E RHardware Features Overview of the Router Hardware FeaturesLocating Chassis Features and Functions Do not Remove During Network OperationGrwic Installation Options AUXGigabit Ethernet Ports Built-in Interface PortsGigabit Ethernet Ports SFP PortsUSB Console Port Removable and Interchangeable Modules and CardsGrid Router WAN Interface Cards Model Description Power SuppliesMemory Hot Swap Internal RPS1 Dual DC2Real-Time Clock LED IndicatorsSlot, Port, and Interface Information PSU 1 OK LEDColor Description SYSConsole EN ACTPSU USB CONSlot SpecificationsGE 0/0 Link OL-31454-01 Preparing for Router Installation Safety Recommendations Safety with Electricity Preventing Electrostatic Discharge DamageRack Requirements General Site RequirementsRouter Environmental Requirements Console and Auxiliary Port Considerations Power Guidelines and RequirementsNetwork Cabling Specifications Console Port ConnectionsAuxiliary Port Connections Preparing for Network ConnectionsUSB Serial Console Port Serial Connections Configuring Serial ConnectionsEthernet Connections Serial DTE or DCE DevicesDistance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices Asynchronous/Synchronous Serial Module Baud Rates 56000 102 16.4 1544000 T1Creating a Site Log Installation ChecklistTask Verified by Date Preparing for Router Installation Creating a Site Log OL-31454-01 Installing and Connecting the Router OL-31454-01 What you Need to Know CLI Console AccessSlot and Port Numbers Before You Begin Unpacking the RouterRack-Mounting the Chassis Installing the Router in a RackCisco CGR 2010 router can only be mounted in a rack Attaching Rack-Mount Brackets to Cisco CGR 2010 Routers PSU OK PWR-150W-HVMounting the Router in a Rack Mounting screwsConnecting AC Power Power-Supply ModulesModel Description Voltage Range Power-Input Terminal Designations Connecting AC Power Using Tie Wraps with the Strain Relief MechanismConnecting DC Power 10 Stripping the Input Power Source Wire Connecting DC Power 11 Using Tie Wraps with the Strain Relief Mechanism 12 CGR 2010 Power Terminal Cover Protecting the Terminal Block from ExposureReplacing Power Supplies and Redundant Power Supplies Shutting Off PowerReplacing the Cisco CGR 2010 Router Power Supply Port Type Cable Section Connecting to a Console Terminal or ModemSerial RJ-45 EIA RJ-45 Connecting to the Serial Port with Microsoft Windows Connecting to the Console Port with Mac OS Connect the OS X USB port to the routerConnecting to the Console Port with Linux To Disconnect the OS X USB Console from the Terminal WindowInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs Utility Uninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramConnecting to the Auxiliary Port AUXConnecting WAN and LAN Interfaces Connection Procedures and PrecautionsAuxiliary and Console Ports Ports and CablingPort or Connection Port Type, Color1 Cable Pin Signal Input/Output Identify a Rollover CableConsole Port Connection to a PC Signal Pin6shows the RJ-45 rolled console cable pinouts Console RJ-45 to RJ-45 Console Port Signaling and Cabling with a DB-9 AdapterSignal RJ-45 Pin DB-9 Pin Port DTE Rollover Cable8shows the pinout descriptions for the DB-25 connections Console Port Signaling and Cabling with a DB-25 AdapterRJ-45 to Console DB-25 Auxiliary Port Connection to a Modem Auxiliary Port Signaling and Cabling Using a DB-25 Adapter9provides the pinout description for the modem connection 10describes the alternative terminal and modem connections Alternative Terminal and Modem ConnectionsRJ-45 Cable Type Adapter Port EIA-232 DCE Ft m Female DB-25 Cable Type Length Connector TypeCAB-HD4-232FC CAB-HD4-232MTPinouts for the Synchronous/Asynchronous Cables Pin Signal Direction DescriptionRS-232 DB-25 Cable Pinouts Ltst RS-232 DB-9 Cable PinoutsRXC TxceRS-232 RJ-45 Cable Pinouts Pin Signal DescriptionSignal Ground Transmit DataChecklist for Power Up Powering up the RouterThis section covers the following topics Power Up Procedure Cisco Setup Command FacilityPerforming the Initial Configuration on the Router Verifying the Power Supply Side LED IndicationsBasic management setup configures only enough connectivity Using the Cisco Setup Command FacilityTo proceed using the setup command facility, enter yes Enter a hostname for the router this example uses myrouterFollowing configuration command script is created Summary of the available interfaces is displayedCompleting the Configuration User prompt is displayedUsing Cisco Configuration Professional Express Using Cisco IOS CLI-Manual ConfigurationPress Return to bring up the Router prompt Configuring the Router HostnameType enable to enter privileged Exec mode Following tasks are either required or optionalRestrictions Configuring the Enable and Enable Secret PasswordsCommand or Action Purpose ExampleBoot older boot ROMs that do not recognize the enable Optional Sets a local password to control access to variousBoot an older image of the Cisco IOS software or if you Secret commandConfiguring the Console Idle Privileged Exec Timeout Verify that you properly configured the idle privileged Configuring Gigabit and FastEthernet InterfacesDisplays the running configuration file Exec timeoutOptional Adds a description to an interface configuration Configuration modeSoftware configuration guide Description helps you remember what is attached toConfiguring the GigabitEthernet Interface Example Specifying a Default Route or Gateway of Last ResortConfiguring IP Routing and IP Protocols Sample Output for the show ip interface brief CommandDefault Network Default RoutesGateway of Last Resort Selects a network as a candidate route for computing Enables IP routingEstablishes a static route Gateway of last resortSpecifying a Default Route Example Sample Output for the show ip route CommandMake sure that you configure all vty lines on your Starts the line configuration command collection mode forVirtual terminal lines vty for remote console access Line vty ? commandLines for remote access Configuring the Auxiliary LineVerify that you properly configured the virtual terminal What to Do NextPrerequisites Verifying Network ConnectivityAuxiliary line Diagnoses initial network connectivity Connected host for each configured interface toTo test the vty line password, perform this step from a To verify connectivity, ping the next hop router orSaves the running configuration to the startup Saving Your Router ConfigurationSaving Backup Copies of Configuration and System Image ConfigurationCopying the Startup Configuration to a Tftp Server Example Copying from Flash Memory to a Tftp Server ExampleVerifying the Initial Configuration NvramInstalling and Upgrading Internal Modules Installing and Upgrading Internal Modules Safety Warnings Removing a Compact Flash Memory Card PSU OKRemoving the Compact Flash Cover Installing a Compact Flash Memory Card Compact Flash Memory Card Slot in Cisco CGRInstalling SFP Modules Laser Safety GuidelinesRemoving SFP Modules Connect the network cable to the SFP moduleDisconnecting SFP Latch Mechanisms Installing Grid Router WAN Interface Cards Installing Single-Wide GRWICsInstalling Double-Wide GRWICs Proper Installation of Multiple GRWICsRemoving the Slot Divider From the CGR 2010 Router 11 Installing the Switch Module in the CGR 2010 Router 12 The Double-Wide Grwic Installed in the CGR 2010 Router OL-31454-01

OL-31454-01 specifications

Cisco Systems OL-31454-01 refers to a specific configuration guide for Cisco networking equipment, which serves an essential role in helping IT professionals understand how to deploy and manage their networking hardware efficiently. This document is particularly relevant for those working with Cisco routers and switches, highlighting various features, technologies, and best practices in network management.

A core feature of Cisco Systems OL-31454-01 is its focus on enhancing network performance and reliability. The systems typically include advanced Quality of Service (QoS) mechanisms, ensuring that critical applications receive the necessary bandwidth and performance even during peak usage times. This is crucial for enterprises that rely on uninterrupted access to applications and services.

The guide also discusses technologies such as VLANs (Virtual Local Area Networks), which allow network administrators to segment networks for improved performance and security. By isolating traffic within different VLANs, organizations can mitigate congestion and enhance overall network efficiency.

Another critical aspect of OL-31454-01 is its in-depth look at security features. Cisco networking solutions typically come equipped with integrated security protocols, such as IPsec for Virtual Private Networks (VPNs) and advanced threat detection mechanisms. This layered approach to security helps protect sensitive data from unauthorized access and cyber threats.

Furthermore, the guide emphasizes the importance of automation and programmability in modern networks. Utilizing Cisco's software-defined networking (SDN) capabilities, network engineers can automate various tasks, reducing the potential for human error and freeing up valuable resources. The integration of tools like Cisco DNA Center provides a unified network management platform, enhancing visibility and control across the entire network.

In addition to these features, Cisco Systems OL-31454-01 outlines various compatibility options with existing technologies and infrastructure. The guide ensures that IT teams can seamlessly integrate new hardware into their current networks without significant overhauls, facilitating a more efficient transition.

Overall, OL-31454-01 serves as a comprehensive resource for deploying and managing Cisco systems, offering valuable insights into essential features, technologies, and best practices that can significantly enhance an organization's networking capabilities.
Top Page Image Contents