Cisco Systems OL-31454-01 Enables IP routing, Establishes a static route, Gateway of last resort

Page 92

Chapter 4 Configuring the Router

Performing the Initial Configuration on the Router

6.end

7.show ip route

DETAILED STEPS

 

Command or Action

Purpose

Step 1

 

 

 

enable

 

Enables privileged EXEC mode.

 

 

 

• Enter your password if prompted.

 

Example:

 

 

 

Router> enable

 

 

Step 2

 

 

configure terminal

Enters global configuration mode.

 

Example:

 

 

 

Router# configure terminal

 

Step 3

 

 

 

ip routing

 

Enables IP routing.

 

Example:

 

 

 

Router(config)# ip routing

 

Step 4

 

 

ip route dest-prefix mask next-hop-ip-address

Establishes a static route.

 

[admin-distance] [permanent]

 

 

Example:

 

 

 

Router(config)# ip route 192.168.24.0

 

 

255.255.255.0

172.28.99.2

 

Step 5

 

 

ip default-network network-number

Selects a network as a candidate route for computing the

 

or

 

gateway of last resort.

 

 

Creates a static route to network 0.0.0.0 0.0.0.0 for

 

 

 

 

ip route dest-prefix mask next-hop-ip-address

computing the gateway of last resort.

 

Example:

 

 

 

Router(config)# ip default-network 192.168.24.0

 

 

Example:

 

 

 

Router(config)# ip route 0.0.0.0 0.0.0.0

 

 

172.28.99.1

 

 

Step 6

 

 

 

end

 

Returns to privileged EXEC mode.

 

Example:

 

 

 

Router(config)# end

 

Step 7

 

 

 

show ip route

 

Displays the current routing table information.

 

 

 

• Verify that the gateway of last resort is set.

 

Example:

 

 

 

Router# show ip route

 

 

 

 

 

 

Cisco 2010 Connected Grid Router Hardware Installation Guide

4-16

OL-31454-01

Page 91 Page 93
Image 92
Page 91 Page 93
Contents Cisco 2010 Connected Grid Router Hardware Installation Guide Page N T E N T S Attaching Rack-Mount Brackets to Cisco CGR 2010 Routers Configuring the Router Verifying the Initial Configuration Objectives AudienceOrganization ConventionsChapter Title Description Convention IndicationBewaar Deze Instructies Aviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Spara Dessa Anvisningar GEM Disse Anvisninger Xiii Xiv Obtaining Documentation and Submitting a Service Request Searching for Cisco DocumentsXvi Chassis Views A P T E RHardware Features Overview of the Router Hardware FeaturesLocating Chassis Features and Functions Do not Remove During Network OperationGrwic Installation Options AUXBuilt-in Interface Ports Gigabit Ethernet PortsGigabit Ethernet Ports SFP PortsGrid Router WAN Interface Cards Removable and Interchangeable Modules and CardsUSB Console Port Power Supplies MemoryModel Description Hot Swap Internal RPS1 Dual DC2LED Indicators Slot, Port, and Interface InformationReal-Time Clock PSU 1 OK LEDColor Description SYSACT PSUConsole EN USB CONGE 0/0 Link SpecificationsSlot OL-31454-01 Preparing for Router Installation Safety Recommendations Safety with Electricity Preventing Electrostatic Discharge DamageRouter Environmental Requirements General Site RequirementsRack Requirements Power Guidelines and Requirements Network Cabling SpecificationsConsole and Auxiliary Port Considerations Console Port ConnectionsUSB Serial Console Port Preparing for Network ConnectionsAuxiliary Port Connections Configuring Serial Connections Ethernet ConnectionsSerial Connections Serial DTE or DCE DevicesDevice Type Gender Typical Devices Signaling Standards SupportedDistance Limitations Asynchronous/Synchronous Serial Module Baud Rates 56000 102 16.4 1544000 T1Task Verified by Date Installation ChecklistCreating a Site Log Preparing for Router Installation Creating a Site Log OL-31454-01 Installing and Connecting the Router OL-31454-01 Slot and Port Numbers CLI Console AccessWhat you Need to Know Before You Begin Unpacking the RouterCisco CGR 2010 router can only be mounted in a rack Installing the Router in a RackRack-Mounting the Chassis Attaching Rack-Mount Brackets to Cisco CGR 2010 Routers PSU OK PWR-150W-HVMounting the Router in a Rack Mounting screwsModel Description Voltage Range Power-Supply ModulesConnecting AC Power Power-Input Terminal Designations Connecting AC Power Using Tie Wraps with the Strain Relief MechanismConnecting DC Power 10 Stripping the Input Power Source Wire Connecting DC Power 11 Using Tie Wraps with the Strain Relief Mechanism 12 CGR 2010 Power Terminal Cover Protecting the Terminal Block from ExposureReplacing the Cisco CGR 2010 Router Power Supply Shutting Off PowerReplacing Power Supplies and Redundant Power Supplies Serial RJ-45 EIA RJ-45 Connecting to a Console Terminal or ModemPort Type Cable Section Connecting to the Serial Port with Microsoft Windows Connecting to the Console Port with Mac OS Connect the OS X USB port to the routerConnecting to the Console Port with Linux To Disconnect the OS X USB Console from the Terminal WindowInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB DriverUsing the Add Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramConnecting to the Auxiliary Port AUXConnecting WAN and LAN Interfaces Connection Procedures and PrecautionsPort or Connection Port Type, Color1 Cable Ports and CablingAuxiliary and Console Ports Pin Signal Input/Output Identify a Rollover Cable6shows the RJ-45 rolled console cable pinouts Signal PinConsole Port Connection to a PC Console Port Signaling and Cabling with a DB-9 Adapter Signal RJ-45 Pin DB-9 PinConsole RJ-45 to RJ-45 Port DTE Rollover CableRJ-45 to Console DB-25 Console Port Signaling and Cabling with a DB-25 Adapter8shows the pinout descriptions for the DB-25 connections 9provides the pinout description for the modem connection Auxiliary Port Signaling and Cabling Using a DB-25 AdapterAuxiliary Port Connection to a Modem RJ-45 Cable Type Adapter Alternative Terminal and Modem Connections10describes the alternative terminal and modem connections Cable Type Length Connector Type CAB-HD4-232FCPort EIA-232 DCE Ft m Female DB-25 CAB-HD4-232MTRS-232 DB-25 Cable Pinouts Pin Signal Direction DescriptionPinouts for the Synchronous/Asynchronous Cables RS-232 DB-9 Cable Pinouts RXCLtst TxcePin Signal Description Signal GroundRS-232 RJ-45 Cable Pinouts Transmit DataThis section covers the following topics Powering up the RouterChecklist for Power Up Power Up Procedure Cisco Setup Command FacilityPerforming the Initial Configuration on the Router Verifying the Power Supply Side LED IndicationsUsing the Cisco Setup Command Facility To proceed using the setup command facility, enter yesBasic management setup configures only enough connectivity Enter a hostname for the router this example uses myrouterFollowing configuration command script is created Summary of the available interfaces is displayedCompleting the Configuration User prompt is displayedUsing Cisco Configuration Professional Express Using Cisco IOS CLI-Manual ConfigurationConfiguring the Router Hostname Type enable to enter privileged Exec modePress Return to bring up the Router prompt Following tasks are either required or optionalConfiguring the Enable and Enable Secret Passwords Command or Action PurposeRestrictions ExampleOptional Sets a local password to control access to various Boot an older image of the Cisco IOS software or if youBoot older boot ROMs that do not recognize the enable Secret commandConfiguring the Console Idle Privileged Exec Timeout Configuring Gigabit and FastEthernet Interfaces Displays the running configuration fileVerify that you properly configured the idle privileged Exec timeoutConfiguration mode Software configuration guideOptional Adds a description to an interface configuration Description helps you remember what is attached toSpecifying a Default Route or Gateway of Last Resort Configuring IP Routing and IP ProtocolsConfiguring the GigabitEthernet Interface Example Sample Output for the show ip interface brief CommandGateway of Last Resort Default RoutesDefault Network Enables IP routing Establishes a static routeSelects a network as a candidate route for computing Gateway of last resortSpecifying a Default Route Example Sample Output for the show ip route CommandStarts the line configuration command collection mode for Virtual terminal lines vty for remote console accessMake sure that you configure all vty lines on your Line vty ? commandConfiguring the Auxiliary Line Verify that you properly configured the virtual terminalLines for remote access What to Do NextAuxiliary line Verifying Network ConnectivityPrerequisites Connected host for each configured interface to To test the vty line password, perform this step from aDiagnoses initial network connectivity To verify connectivity, ping the next hop router orSaving Your Router Configuration Saving Backup Copies of Configuration and System ImageSaves the running configuration to the startup ConfigurationCopying the Startup Configuration to a Tftp Server Example Copying from Flash Memory to a Tftp Server ExampleVerifying the Initial Configuration NvramInstalling and Upgrading Internal Modules Installing and Upgrading Internal Modules Safety Warnings Removing a Compact Flash Memory Card PSU OKRemoving the Compact Flash Cover Installing a Compact Flash Memory Card Compact Flash Memory Card Slot in Cisco CGRInstalling SFP Modules Laser Safety GuidelinesRemoving SFP Modules Connect the network cable to the SFP moduleDisconnecting SFP Latch Mechanisms Installing Grid Router WAN Interface Cards Installing Single-Wide GRWICsInstalling Double-Wide GRWICs Proper Installation of Multiple GRWICsRemoving the Slot Divider From the CGR 2010 Router 11 Installing the Switch Module in the CGR 2010 Router 12 The Double-Wide Grwic Installed in the CGR 2010 Router OL-31454-01

OL-31454-01 specifications

Cisco Systems OL-31454-01 refers to a specific configuration guide for Cisco networking equipment, which serves an essential role in helping IT professionals understand how to deploy and manage their networking hardware efficiently. This document is particularly relevant for those working with Cisco routers and switches, highlighting various features, technologies, and best practices in network management.

A core feature of Cisco Systems OL-31454-01 is its focus on enhancing network performance and reliability. The systems typically include advanced Quality of Service (QoS) mechanisms, ensuring that critical applications receive the necessary bandwidth and performance even during peak usage times. This is crucial for enterprises that rely on uninterrupted access to applications and services.

The guide also discusses technologies such as VLANs (Virtual Local Area Networks), which allow network administrators to segment networks for improved performance and security. By isolating traffic within different VLANs, organizations can mitigate congestion and enhance overall network efficiency.

Another critical aspect of OL-31454-01 is its in-depth look at security features. Cisco networking solutions typically come equipped with integrated security protocols, such as IPsec for Virtual Private Networks (VPNs) and advanced threat detection mechanisms. This layered approach to security helps protect sensitive data from unauthorized access and cyber threats.

Furthermore, the guide emphasizes the importance of automation and programmability in modern networks. Utilizing Cisco's software-defined networking (SDN) capabilities, network engineers can automate various tasks, reducing the potential for human error and freeing up valuable resources. The integration of tools like Cisco DNA Center provides a unified network management platform, enhancing visibility and control across the entire network.

In addition to these features, Cisco Systems OL-31454-01 outlines various compatibility options with existing technologies and infrastructure. The guide ensures that IT teams can seamlessly integrate new hardware into their current networks without significant overhauls, facilitating a more efficient transition.

Overall, OL-31454-01 serves as a comprehensive resource for deploying and managing Cisco systems, offering valuable insights into essential features, technologies, and best practices that can significantly enhance an organization's networking capabilities.
Top Page Image Contents