Cisco Systems OL-31454-01 manual Installing the Cisco Microsoft Windows XP USB Driver

Page 61

Chapter 3 Installing and Connecting the Router

Installing the Cisco Microsoft Windows USB Device Driver

Installing the Cisco Microsoft Windows USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB serial port on the router.

This section contains the following topics:

•Installing the Cisco Microsoft Windows XP USB Driver

•Installing the Cisco Microsoft Windows 2000 USB Driver

•Installing the Cisco Microsoft Windows Vista USB Driver

Installing the Cisco Microsoft Windows XP USB Driver

This procedure shows how to install the Microsoft Windows XP USB driver.

Step 1 Obtain the file Cisco_usbconsole_driver.zip from www.cisco.com website and unzip it.

Step 2 If using 32-bit Windows XP, double-click the setup.exe file from the Windows_32 folder. If using 64-bit Windows XP, double-click the setup(x64).exe file from the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Click Next.

Step 4 The Ready to Install the Program window appears. Click Install.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and router USB console ports. See Table 3-2 on page 3-17The EN LED for the USB console port turns green, and the Found New Hardware wizard appears.

Step 7 Follow the Found New Hardware wizard instructions to complete the installation of the driver. The USB console is now ready for use.

Installing the Cisco Microsoft Windows 2000 USB Driver

This procedure shows how to install the Microsoft Windows 2000 USB driver.

Step 1 Obtain the file Cisco_usbconsole_driver.zip from www.cisco.com and unzip it.

Step 2 Double-click the file setup.exe.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Click Next.

Step 4 The Ready to Install the Program window appears. Click Install.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and router USB console ports. See Table 3-2 on page 3-17The EN LED for the USB console port turns green, and the Found New Hardware wizard appears.

Step 7 Follow the Found New Hardware wizard instructions to complete the installation of the driver. The USB console is now ready for use.

 

 

Cisco 2010 Connected Grid Router Hardware Installation Guide

 

 

 

 

 

 

OL-31454-01

 

 

3-21

 

 

 

 

 

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Cisco 2010 Connected Grid Router Hardware Installation Guide Page N T E N T S Attaching Rack-Mount Brackets to Cisco CGR 2010 Routers Configuring the Router Verifying the Initial Configuration Audience ObjectivesConventions OrganizationChapter Title Description Convention IndicationBewaar Deze Instructies Avvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Xiii Xiv Searching for Cisco Documents Obtaining Documentation and Submitting a Service RequestXvi A P T E R Chassis ViewsOverview of the Router Hardware Features Hardware FeaturesDo not Remove During Network Operation Locating Chassis Features and FunctionsAUX Grwic Installation OptionsGigabit Ethernet Ports Built-in Interface PortsGigabit Ethernet Ports SFP PortsUSB Console Port Removable and Interchangeable Modules and CardsGrid Router WAN Interface Cards Memory Power SuppliesModel Description Hot Swap Internal RPS1 Dual DC2Slot, Port, and Interface Information LED IndicatorsReal-Time Clock PSU 1 OK LEDSYS Color DescriptionPSU ACTConsole EN USB CONSlot SpecificationsGE 0/0 Link OL-31454-01 Preparing for Router Installation Safety Recommendations Preventing Electrostatic Discharge Damage Safety with ElectricityRack Requirements General Site RequirementsRouter Environmental Requirements Network Cabling Specifications Power Guidelines and RequirementsConsole and Auxiliary Port Considerations Console Port ConnectionsAuxiliary Port Connections Preparing for Network ConnectionsUSB Serial Console Port Ethernet Connections Configuring Serial ConnectionsSerial Connections Serial DTE or DCE DevicesDistance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices 56000 102 16.4 1544000 T1 Asynchronous/Synchronous Serial Module Baud RatesCreating a Site Log Installation ChecklistTask Verified by Date Preparing for Router Installation Creating a Site Log OL-31454-01 Installing and Connecting the Router OL-31454-01 What you Need to Know CLI Console AccessSlot and Port Numbers Unpacking the Router Before You BeginRack-Mounting the Chassis Installing the Router in a RackCisco CGR 2010 router can only be mounted in a rack PSU OK PWR-150W-HV Attaching Rack-Mount Brackets to Cisco CGR 2010 RoutersMounting screws Mounting the Router in a RackConnecting AC Power Power-Supply ModulesModel Description Voltage Range Power-Input Terminal Designations Using Tie Wraps with the Strain Relief Mechanism Connecting AC PowerConnecting DC Power 10 Stripping the Input Power Source Wire Connecting DC Power 11 Using Tie Wraps with the Strain Relief Mechanism Protecting the Terminal Block from Exposure 12 CGR 2010 Power Terminal CoverReplacing Power Supplies and Redundant Power Supplies Shutting Off PowerReplacing the Cisco CGR 2010 Router Power Supply Port Type Cable Section Connecting to a Console Terminal or ModemSerial RJ-45 EIA RJ-45 Connecting to the Serial Port with Microsoft Windows Connect the OS X USB port to the router Connecting to the Console Port with Mac OSTo Disconnect the OS X USB Console from the Terminal Window Connecting to the Console Port with LinuxInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB DriverAUX Connecting to the Auxiliary PortConnection Procedures and Precautions Connecting WAN and LAN InterfacesAuxiliary and Console Ports Ports and CablingPort or Connection Port Type, Color1 Cable Identify a Rollover Cable Pin Signal Input/OutputConsole Port Connection to a PC Signal Pin6shows the RJ-45 rolled console cable pinouts Signal RJ-45 Pin DB-9 Pin Console Port Signaling and Cabling with a DB-9 AdapterConsole RJ-45 to RJ-45 Port DTE Rollover Cable8shows the pinout descriptions for the DB-25 connections Console Port Signaling and Cabling with a DB-25 AdapterRJ-45 to Console DB-25 Auxiliary Port Connection to a Modem Auxiliary Port Signaling and Cabling Using a DB-25 Adapter9provides the pinout description for the modem connection 10describes the alternative terminal and modem connections Alternative Terminal and Modem ConnectionsRJ-45 Cable Type Adapter CAB-HD4-232FC Cable Type Length Connector TypePort EIA-232 DCE Ft m Female DB-25 CAB-HD4-232MTPinouts for the Synchronous/Asynchronous Cables Pin Signal Direction DescriptionRS-232 DB-25 Cable Pinouts RXC RS-232 DB-9 Cable PinoutsLtst TxceSignal Ground Pin Signal DescriptionRS-232 RJ-45 Cable Pinouts Transmit DataChecklist for Power Up Powering up the RouterThis section covers the following topics Cisco Setup Command Facility Power Up ProcedureVerifying the Power Supply Side LED Indications Performing the Initial Configuration on the RouterTo proceed using the setup command facility, enter yes Using the Cisco Setup Command FacilityBasic management setup configures only enough connectivity Enter a hostname for the router this example uses myrouterSummary of the available interfaces is displayed Following configuration command script is createdUser prompt is displayed Completing the ConfigurationUsing Cisco IOS CLI-Manual Configuration Using Cisco Configuration Professional ExpressType enable to enter privileged Exec mode Configuring the Router HostnamePress Return to bring up the Router prompt Following tasks are either required or optionalCommand or Action Purpose Configuring the Enable and Enable Secret PasswordsRestrictions ExampleBoot an older image of the Cisco IOS software or if you Optional Sets a local password to control access to variousBoot older boot ROMs that do not recognize the enable Secret commandConfiguring the Console Idle Privileged Exec Timeout Displays the running configuration file Configuring Gigabit and FastEthernet InterfacesVerify that you properly configured the idle privileged Exec timeoutSoftware configuration guide Configuration modeOptional Adds a description to an interface configuration Description helps you remember what is attached toConfiguring IP Routing and IP Protocols Specifying a Default Route or Gateway of Last ResortConfiguring the GigabitEthernet Interface Example Sample Output for the show ip interface brief CommandDefault Network Default RoutesGateway of Last Resort Establishes a static route Enables IP routingSelects a network as a candidate route for computing Gateway of last resortSample Output for the show ip route Command Specifying a Default Route ExampleVirtual terminal lines vty for remote console access Starts the line configuration command collection mode forMake sure that you configure all vty lines on your Line vty ? commandVerify that you properly configured the virtual terminal Configuring the Auxiliary LineLines for remote access What to Do NextPrerequisites Verifying Network ConnectivityAuxiliary line To test the vty line password, perform this step from a Connected host for each configured interface toDiagnoses initial network connectivity To verify connectivity, ping the next hop router orSaving Backup Copies of Configuration and System Image Saving Your Router ConfigurationSaves the running configuration to the startup ConfigurationCopying from Flash Memory to a Tftp Server Example Copying the Startup Configuration to a Tftp Server ExampleNvram Verifying the Initial ConfigurationInstalling and Upgrading Internal Modules Installing and Upgrading Internal Modules Safety Warnings PSU OK Removing a Compact Flash Memory CardRemoving the Compact Flash Cover Compact Flash Memory Card Slot in Cisco CGR Installing a Compact Flash Memory CardLaser Safety Guidelines Installing SFP ModulesConnect the network cable to the SFP module Removing SFP ModulesDisconnecting SFP Latch Mechanisms Installing Single-Wide GRWICs Installing Grid Router WAN Interface CardsProper Installation of Multiple GRWICs Installing Double-Wide GRWICsRemoving the Slot Divider From the CGR 2010 Router 11 Installing the Switch Module in the CGR 2010 Router 12 The Double-Wide Grwic Installed in the CGR 2010 Router OL-31454-01

OL-31454-01 specifications

Cisco Systems OL-31454-01 refers to a specific configuration guide for Cisco networking equipment, which serves an essential role in helping IT professionals understand how to deploy and manage their networking hardware efficiently. This document is particularly relevant for those working with Cisco routers and switches, highlighting various features, technologies, and best practices in network management.

A core feature of Cisco Systems OL-31454-01 is its focus on enhancing network performance and reliability. The systems typically include advanced Quality of Service (QoS) mechanisms, ensuring that critical applications receive the necessary bandwidth and performance even during peak usage times. This is crucial for enterprises that rely on uninterrupted access to applications and services.

The guide also discusses technologies such as VLANs (Virtual Local Area Networks), which allow network administrators to segment networks for improved performance and security. By isolating traffic within different VLANs, organizations can mitigate congestion and enhance overall network efficiency.

Another critical aspect of OL-31454-01 is its in-depth look at security features. Cisco networking solutions typically come equipped with integrated security protocols, such as IPsec for Virtual Private Networks (VPNs) and advanced threat detection mechanisms. This layered approach to security helps protect sensitive data from unauthorized access and cyber threats.

Furthermore, the guide emphasizes the importance of automation and programmability in modern networks. Utilizing Cisco's software-defined networking (SDN) capabilities, network engineers can automate various tasks, reducing the potential for human error and freeing up valuable resources. The integration of tools like Cisco DNA Center provides a unified network management platform, enhancing visibility and control across the entire network.

In addition to these features, Cisco Systems OL-31454-01 outlines various compatibility options with existing technologies and infrastructure. The guide ensures that IT teams can seamlessly integrate new hardware into their current networks without significant overhauls, facilitating a more efficient transition.

Overall, OL-31454-01 serves as a comprehensive resource for deploying and managing Cisco systems, offering valuable insights into essential features, technologies, and best practices that can significantly enhance an organization's networking capabilities.
Top Page Image Contents