Cisco IOS Software Configuration for the
How to Configure the
–show controllers oc12 slot/port:channel#
Verify the Cisco Remote Connection Management configuration by entering the
show controllers oc12 slot/port:channel# command, as shown in the following example:
Router# show controllers oc12 1/0:1
Controller OC12 1/0, interface Serial1/0:1 (DS3 channel 1) cdb = 0x616BED10, base_hwidb = 0x613B5540, hwidb = 0x613B6520 ssb = 0x616C46A0, ds = 0x616C43E8
Line state is up
rxLOS inactive, rxLOF inactive, rxAIS inactive txAIS inactive, rxRAI inactive, txRAI inactive
Current configurable parameter settings: Loopback is none, Framing is
DSU mode is cisco, DSU bandwidth limit is 44210 Payload scrambling is disabled, CRC is 16 Bert pattern is disabled, Bert interval is 0 Transmitter delay is 0, Encapsulation is HDLC Idle character is flags, Invert data is disabled Remote fullrate has no request outstanding Remote accept is enabled, MTU is 4470
MIB information:
Data in current interval (366 seconds elapsed):
0Line Code Violations, 0
0
0
0Sev Err Framing Secs, 0 Unavailable Secs
0Line Errored Secs, 0
No alarms detected.
Router#
–show controllers oc12 detail
View details about an
Router# | show controllers oc12 | detail |
|
| ||||
OC12_CH_DS31/0 |
|
|
|
|
|
| ||
The | current state of the controller is up |
|
| |||||
Current configurable parameter settings: |
|
| ||||||
Clock | source is INTERNAL, Loopback is NONE |
|
| |||||
SECTION |
|
|
|
|
|
|
| |
LOF = | 0 | LOS | = 0 |
| RDOOL | = 0 | BIP(B1) = 0 | |
Active Alarms: None |
|
|
|
|
| |||
LINE |
|
|
|
|
|
|
|
|
AIS = | 0 | RDI |
| = 0 | FEBE = 0 | BIP(B2) = 0 | ||
Active Alarms: None |
|
|
|
|
| |||
PATH | 1 |
|
|
|
|
|
|
|
AIS = | 0 | RDI | = 0 |
| FEBE = 0 |
| BIP(B3) = 0 | |
LOP = | 0 | NEWPTR = 0 | PSE = | 0 | NSE = 0 | |||
Active Alarms: None |
|
|
|
|
| |||
S1S0 = 02, C2 = 04 |
|
|
|
|
| |||
PATH TRACE BUFFER : STABLE |
|
|
| |||||
61 | 6D | 69 74 2D 62 66 | 72 | 00 | 00 00 00 00 00 | 00 00 | ||
00 | 00 | 00 00 00 00 00 | 00 | 53 | 65 72 69 61 6C | 35 2F | ........Serial5/ | |
30 | 3A | 31 00 00 00 31 | 30 | 31 | 2E 35 2E 31 2E | 31 00 | 0:1...101.5.1.1. | |
00 | 00 | 00 00 00 00 30 | 30 | 30 | 30 30 30 30 30 | 0D 0A | ......00000000.. | |
PATH | 2 |
|
|
|
|
|
|
|
AIS = | 0 | RDI | = 0 |
| FEBE = 0 |
| BIP(B3) = 0 | |
LOP = | 0 | NEWPTR = 0 | PSE = | 0 | NSE = 0 | |||
Active Alarms: None |
|
|
|
|
| |||
S1S0 = 03, C2 = FF |
|
|
|
|
| |||
PATH TRACE BUFFER : STABLE |
|
|
| |||||
FF | FF | FF FF FF FF FF | FF | FF | FF FF FF FF FF | FF FF | ................ | |
FF | FF | FF FF FF FF FF | FF | FF | FF FF FF FF FF | FF FF | ................ |
Cisco IOS Release 12.0(8)S
10