Cisco Systems WRK54G manual Frequently Asked Questions

Page 54

Wireless-G Broadband Router

Frequently Asked Questions

After using SecureEasySetup, my existing wireless devices can no longer connect to the Router. SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices. Re-run the Setup Wizard. On the Welcome screen for the Setup Wizard, click Click Here to Start and follow the on-screen instructions. On the Configure Wireless Settings screen, click Enter Wireless Settings Manually and continue to follow the on- screen instructions. For more information, refer to “Chapter 5: Setting up the Wireless-G Broadband Router.”

How do I set up additional devices using SecureEasySetup?

Repeat the SecureEasySetup process for each device until all of your devices have been configured.

Where is my SecureEasySetup button?

On the Router, the SecureEasySetup button is located on the front panel. The button should be lighted either orange or white. For other SecureEasySetup devices, refer to each wireless device's documentation to locate the button on that device.

I have devices that support WPA-Personal security, but do not have SecureEasySetup. Can I still use

SecureEasySetup?

Yes. Print out the wireless security settings at the end of the SecureEasySetup process, and then manually configure the settings for your non-SecureEasySetup devices. Refer to each wireless device’s documentation for instructions on how to enter these settings.

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

48

Frequently Asked Questions

Image 54
Contents 802 GHz .11g Wireless- G Copyright and Trademarks Word definitionTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityAppendix C Upgrading Firmware Appendix D Windows Help List of Figures Router’s Back Panel23 Wireless Tab Wireless Security Radius Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Broadband Router Back PanelFront Panel DMZConnecting the Wireless-G Broadband Router OverviewConnecting Your Network Devices Hardware Installation for Connection to Another Router Router Wireless-G Broadband Multiple PCsConnecting the Power Configuring the Wireless-G Broadband Router Password ScreenSetup Tab Basic Setup Internet SetupPPPoE Connection Type L2TP Connection Type Optional Settings Network Address Server Settings Dhcp Setup Tab Ddns 13 Setup Tab Ddns DynDNS accountSetup Tab MAC Address Clone 15 Setup Tab MAC Address CloneSetup Tab Advanced Routing 16 Setup Tab Advanced Routing GatewayWireless Tab Basic Wireless Settings Wireless Tab Wireless Security 19 Wireless Tab Wireless Security WPA Personal22 Wireless Tab Wireless Security WPA2 Enterprise 23 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter 25 Wireless Tab Wireless MAC FilterWireless Tab Advanced Wireless Settings Synchronize the wireless networkSecurity Tab Firewall Security Tab VPN PassthroughAccess Restrictions Tab Internet Access To create an Internet Access policy33 Port Services Applications and Gaming Tab Port Range Forward 34 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Triggering Port TriggeringApplications and Gaming Tab DMZ Applications and Gaming Tab QoSAdd a New Application For the application Administration Tab Management Administration Tab LogAdministration Tab Diagnostics 41 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management Status Tab Router 47 Status Tab RouterStatus Tab Wireless Status Tab Local NetworkAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Broadband Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Wireless-G Broadband Router Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What is ad-hoc mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareAppendix D Windows Help TCP/IPWindows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Appendix G Specifications WRK54GOperating Temp Appendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementSafety Notices Appendix J Contact Information

WRK54G specifications

The Cisco Systems WRK54G is a versatile wireless router designed to meet the demands of home and small office networking. Renowned for its reliability, it offers a range of features that cater to both casual users and tech-savvy individuals.

At its core, the WRK54G is built on the IEEE 802.11g standard, which supports data transfer rates of up to 54 Mbps. This makes it suitable for various internet-based applications, including browsing, streaming, and online gaming. Additionally, it is backward compatible with the earlier 802.11b standard, ensuring that users with older devices can still enjoy connectivity.

One of the standout features of the WRK54G is its wireless connectivity, which allows users to connect multiple devices without the need for cumbersome cabling. This is especially beneficial in environments where mobility is essential. The router employs robust security protocols, including WEP, WPA, and WPA2, to safeguard the network from unauthorized access and ensure the integrity of data transmission.

In terms of hardware, the WRK54G is equipped with a built-in four-port Ethernet switch, enabling wired connections for devices that require stable and faster internet access, such as desktop computers and gaming consoles. This dual capability of wired and wireless networking makes it a flexible solution for diverse user needs.

Another noteworthy characteristic of the WRK54G is its support for Quality of Service (QoS) functionalities. QoS technology prioritizes bandwidth for specific applications, ensuring that essential services such as VoIP and video streaming receive the necessary resources for optimal performance. This feature is vital for users who rely on uninterrupted internet access for work or entertainment.

Additionally, the router features an intuitive web-based interface that simplifies setup and configuration. Users can easily manage their network settings, create a secure wireless environment, and monitor connected devices without requiring extensive technical knowledge.

In conclusion, the Cisco Systems WRK54G is a reliable and feature-rich wireless router that supports modern networking demands. With its solid performance, robust security measures, dual connectivity options, and user-friendly interface, it remains a practical choice for both home and small business users looking to establish a seamless network experience. Whether for streaming, gaming, or web browsing, the WRK54G provides a solid foundation for a comprehensive wireless networking solution.