Cisco Systems VIP-4R/4T manual Configuring the 4T Interfaces

Page 60

VIP Port Adapter Functions

Configuring the 4T Interfaces

If you installed a new VIP or if you want to change the configuration of an existing interface, you must enter Configuration mode to configure the new interfaces. If you replaced a VIP that was previously configured, the system will recognize the new 4T port adapter interfaces and bring each of them up in their existing configuration.

After you verify that the new 4T port adapter is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Be prepared with the information you will need, such as the following:

Protocols you plan to route on each new interface

Internet protocol (IP) addresses if you will configure the interfaces for IP routing

Whether or not the new interfaces will use bridging

Timing source for each new interface and clock speeds for external timing

Refer to the appropriate software documentation for descriptions of the configuration options available and instructions for configuring a serial interface.

The following sections describe the commands for configuring an external clock signal for a DCE interface and for configuring a port for NRZI encoding or 32-bit CRC. Configuration commands are executed from the privileged level of the EXEC command interpreter, which usually requires password access. (See the section “Using the EXEC Command Interpreter” on page 69.) Refer to the description that follows and contact your system administrator, if necessary, to obtain access.

Selecting Chassis Slot, Port Adapter, and Serial Interface Port Numbers

The following section describes how to identify chassis slot, port adapter, and serial interface port numbers.

Note Although the processor slots in the seven-slot Cisco 7000 and 13-slot Cisco 7513 are vertically oriented and those in the five-slot Cisco 7010 and Cisco 7505 are horizontally oriented, all models use the same method for slot and port numbering. (For interface processor slot orientation in your chassis, refer to Figure 2, Figure 3, Figure 4, Figure 5, or Figure 6.)

In the router, physical port addresses specify the actual physical location of each interface port on the router interface processor end. (See Figure 32.) This address is composed of a three-part number in the format chassis slot number/port adapter number/interface port number.

The first number identifies the chassis slot in which the VIP is installed (as shown in the example system in Figure 32). The second number identifies the physical port adapter number on the VIP, and is either 0 or 1. The interface ports on each 4T port adapter are always numbered in sequence as interface 0 through 3.

60VIP-4R/4T Installation and Configuration

Image 60
Contents VIP-4R/4T Installation and Configuration Table of Contents What is the VIP? Versatile Interface Processor FunctionsDram What is the Cisco 7000 Family? VIP Software PrerequisitesVIP Hardware Prerequisites Cisco 7000 Series Cisco 7000, Interface Processor EndCisco 7500 Series Cisco 7010, Interface Processor EndCisco 7507, Interface Processor End Cisco 7513, Interface Processor End VIP Port Adapter Hardware Configuration Overview VIP Installation Prerequisites VIP Microcode OverviewList of Parts and Tools Safety Guidelines Telephone Wiring GuidelinesElectrical Equipment Guidelines Preventing Electrostatic Discharge DamageOnline Insertion and Removal-An Overview Versatile Interface Processor Functions H1984 VIP Installation Removing an Interface Processor FillerRemoving a VIP Captive installation screws Installing a VIP Checking the Installation and Verifying VIP Status Checking the VIP InstallationVersatile Interface Processor Functions Verifying VIP Status Using show Commands Router# show protocols Upgrading VIP Microcode Router# show flash Loaded from Flash Upgrading and Replacing Dram SIMMs Handling a Dram SIMM-Example OnlyOrientation of Dram SIMMs U1 and U2 on VIP Motherboard Removing and Replacing Dram SIMMs VIP Port Adapter Functions 4R Port AdapterToken Ring Overview Token Ring Specifications and Physical ConnectionsVIP Port Adapter Functions Token Ring Connection Equipment Token Ring Network Physical ConnectionsToken Ring Distance Limitations Token Ring Speed Considerations4R Port Adapter LEDs 4R Port Adapter Receptacles, Cables, and Pinouts 4R Port Adapter Receptacles and Cables4R Port Adapter Receptacle Pinout Attaching 4R Port Adapter Interface CablesSetup Configure Configuring the 4R InterfacesUsing the Exec Command Interpreter Using the Setup CommandRouter# setup Using the Configure Exec Command 4R Token Ring Interface Port Number Example Cisco 7505 Shown 4R Slot, Port Adapter, and Port Numbers in a Cisco 4R Slot, Port Adapter, and Port Numbers in a Cisco ARP type ARPA, ARP Timeout Basic Configuration GuidelinesChecking the Configuration 4T Port Adapter Synchronous Serial OverviewVIP Port Adapter Functions Shows the 4T port adapter installed on the VIP-4R/4T 4T Port Adapter SpecificationsSerial Distance Limitations 4T Serial Connection EquipmentEIA/TIA-232 Connections EIA/TIA-449 Connections ConnectionsEIA-530 Connections 4T Port Adapter LEDs4T Port Adapter Receptacles, Cables, and Pinouts Serial Port Adapter Receptacles and CablesVIP Port Adapter Functions Serial Port Adapter Cable Pinouts Serial Port Adapter CablesRTS/CTS CTS/RTS DSR/DTR DTR/DSR SD+ RTS/CTS RTS/CTS CTS/RTS DSR/DTR DTR/DSR DCD/LL Rlsd LL/DCD RTS/CTS+ RTS+ CTS/RTS+ DSR/DTR+ DSR+ DCD/DCD+ Attaching 4T Port Adapter Interface Cables CorrectIncorrect, cable upside down Configuring the 4T Interfaces 4T Serial Interface Port Number Example Cisco 7505 Shown 4T Slot, Port Adapter, and Port Numbers in a Cisco Slot Adapter Port Port n Serial3/1/0 is administratively down, line protocol is down Configuring Timing Clock Signals Setting the Clock RateInverting the Clock Signal Configuring Nrzi FormatConfiguring CRCs Replacing Port Adapter CablesEnter Configuration mode again and bring the port back up Enter the shutdown command, as follows Shutting Down an InterfaceConfiguring Interfaces Router# show int serial 1/1/0Write the new configuration to memory as follows Using Show Commands to Verify the VIP Status Using the ping and loopback CommandsRouter# ping 1.1.1.10 Return Type escape sequence to abort Cisco Information Online