Cisco Systems VIP-4R/4T manual Configuring the 4R Interfaces, Setup Configure

Page 36

VIP Port Adapter Functions

Step 2 Attach the port adapter end of a Token Ring interface cable, or other connection equipment, to the interface port. (See Figure 19).

Note Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate.

Figure 19 Token Ring Interface Cable Connections

EN

 

 

RC

 

CD

 

 

 

RC

 

CD

 

 

 

RC

 

CD

 

FAST SERIAL

TD

TC

RD

LB

TD

TC

RD

LB

TD

TC

RD

LB

TD

TC

RD

RC

LB

H5986

To MAU or MSAU

Caution Each 4R port adapter interface must be configured for the same ring speed as the ring to which it is connected; either 4 or 16 Mbps. If the 4R port adapter interface is set for a different speed, it will cause the ring to beacon, which effectively brings the ring down and makes it inoperable.

Step 3 Attach the network end of the Token Ring interface cable to the appropriate Token Ring equipment at your site: a MAU or MSAU.

Configuring the 4R Interfaces

You can modify the startup configuration for Cisco 7000 series and Cisco 7500 series routers through the software command interpreter called EXEC. To configure the interfaces for interface processors, you can use either one of the setup or configure EXEC commands:

setup

configure

The setup command facility can be used after first time startup to make basic changes at any time. The changes you make will affect only the changed elements’ current memory values that are stored in nonvolatile memory.

The configure privileged EXEC command enables you to perform advanced configurations such as specifying interfaces. The EXEC interprets the commands you enter and carries out the corresponding operations. You can list available EXEC commands by entering a question mark (?). You also can enter a question mark to obtain more information about commands. For example, enter terminal ? to obtain a list of terminal commands or show ? to obtain a list of show commands.

36VIP-4R/4T Installation and Configuration

Image 36
Contents VIP-4R/4T Installation and Configuration Table of Contents What is the VIP? Versatile Interface Processor FunctionsDram What is the Cisco 7000 Family? VIP Software PrerequisitesVIP Hardware Prerequisites Cisco 7000 Series Cisco 7000, Interface Processor EndCisco 7500 Series Cisco 7010, Interface Processor EndCisco 7507, Interface Processor End Cisco 7513, Interface Processor End VIP Port Adapter Hardware Configuration Overview VIP Installation Prerequisites VIP Microcode OverviewList of Parts and Tools Safety Guidelines Telephone Wiring GuidelinesElectrical Equipment Guidelines Preventing Electrostatic Discharge DamageOnline Insertion and Removal-An Overview Versatile Interface Processor Functions H1984 VIP Installation Removing an Interface Processor FillerRemoving a VIP Captive installation screws Installing a VIP Checking the Installation and Verifying VIP Status Checking the VIP InstallationVersatile Interface Processor Functions Verifying VIP Status Using show Commands Router# show protocols Upgrading VIP Microcode Router# show flash Loaded from Flash Upgrading and Replacing Dram SIMMs Handling a Dram SIMM-Example OnlyOrientation of Dram SIMMs U1 and U2 on VIP Motherboard Removing and Replacing Dram SIMMs VIP Port Adapter Functions 4R Port AdapterToken Ring Overview Token Ring Specifications and Physical ConnectionsVIP Port Adapter Functions Token Ring Connection Equipment Token Ring Network Physical ConnectionsToken Ring Distance Limitations Token Ring Speed Considerations4R Port Adapter LEDs 4R Port Adapter Receptacles, Cables, and Pinouts 4R Port Adapter Receptacles and Cables4R Port Adapter Receptacle Pinout Attaching 4R Port Adapter Interface CablesSetup Configure Configuring the 4R InterfacesUsing the Exec Command Interpreter Using the Setup CommandRouter# setup Using the Configure Exec Command 4R Token Ring Interface Port Number Example Cisco 7505 Shown 4R Slot, Port Adapter, and Port Numbers in a Cisco 4R Slot, Port Adapter, and Port Numbers in a Cisco ARP type ARPA, ARP Timeout Basic Configuration GuidelinesChecking the Configuration 4T Port Adapter Synchronous Serial OverviewVIP Port Adapter Functions Shows the 4T port adapter installed on the VIP-4R/4T 4T Port Adapter SpecificationsSerial Distance Limitations 4T Serial Connection EquipmentEIA/TIA-232 Connections EIA/TIA-449 Connections ConnectionsEIA-530 Connections 4T Port Adapter LEDs4T Port Adapter Receptacles, Cables, and Pinouts Serial Port Adapter Receptacles and CablesVIP Port Adapter Functions Serial Port Adapter Cable Pinouts Serial Port Adapter CablesRTS/CTS CTS/RTS DSR/DTR DTR/DSR SD+ RTS/CTS RTS/CTS CTS/RTS DSR/DTR DTR/DSR DCD/LL Rlsd LL/DCD RTS/CTS+ RTS+ CTS/RTS+ DSR/DTR+ DSR+ DCD/DCD+ Attaching 4T Port Adapter Interface Cables CorrectIncorrect, cable upside down Configuring the 4T Interfaces 4T Serial Interface Port Number Example Cisco 7505 Shown 4T Slot, Port Adapter, and Port Numbers in a Cisco Slot Adapter Port Port n Serial3/1/0 is administratively down, line protocol is down Configuring Timing Clock Signals Setting the Clock RateInverting the Clock Signal Configuring Nrzi FormatConfiguring CRCs Replacing Port Adapter CablesEnter Configuration mode again and bring the port back up Enter the shutdown command, as follows Shutting Down an InterfaceConfiguring Interfaces Router# show int serial 1/1/0Write the new configuration to memory as follows Using Show Commands to Verify the VIP Status Using the ping and loopback CommandsRouter# ping 1.1.1.10 Return Type escape sequence to abort Cisco Information Online