Cisco Systems WRT110 manual Wireless Basic Wireless Settings, Routing Table

Page 14

Chapter 3

Advanced Configuration

Gateway  This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Interface  This interface tells you whether the Destination IP Address is on the LAN & Wireless (Ethernet and wireless networks) or the WAN (Internet).

Click Show Routing Table to view the static routes you have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. Click Close to exit this screen.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup.

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup.

Wireless Configuration  To manually configure your wireless network, select Manual. Proceed to the “Basic Wireless Settings” section. To use Wi-Fi Protected Setup, select Wi-Fi Protected Setup. Proceed to the “Wi-Fi Protected Setup” section.

Wireless > Basic Wireless Settings

Basic Wireless Settings

Network Mode  From this drop-down menu, you can select the wireless standards running on your network. If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, keep the default setting, Mixed. If you have only Wireless-G and Wireless-B devices in your network, select BG-Mixed. If you have only Wireless-N devices, select Wireless-N Only. If you have only Wireless-G devices, select Wireless-G Only. If you have only Wireless- B devices, select Wireless-B Only. If you do not have any wireless devices in your network, select Disabled.

Network Name (SSID)  The SSID is the network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Radio Band  For best performance in a network using Wireless-N, Wireless-G and Wireless-B devices, keep the default, Auto - 20/40MHz Channel. For Wireless-G and Wireless-B networking only, select Standard - 20MHz Channel.

NOTE: If you select Auto - 20/40MHz Channel for the Radio Band setting, then Wireless-N can use two channels: a primary one (Wide Channel) and a secondary one (Standard Channel). This will enhance Wireless-N performance.

Wide Channel  If you selected Auto - 20/40MHz Channel for the Radio Band setting, then this setting will be available for your primary Wireless-N channel. Select any channel from the drop-down menu. If you are not sure which channel to select, keep the default, Auto.

Standard Channel  Select the channel for Wireless-N, Wireless-G, and Wireless-B networking. If you selected Auto – 20/40MHz Channel for the Radio Band setting, then the Standard Channel will be a secondary channel

RangePlus Wireless Router

13

Image 14
Contents RangePlus Wireless Router Online Resources About This GuideIcon Descriptions Copyright and TrademarksTable of Contents Appendix D Regulatory Information Appendix E Software License AgreementFront Panel Horizontal PlacementChapter Product Overview Back PanelWall-Mounting Placement Suggested Mounting HardwareAdditional Security Tips Chapter Wireless Security ChecklistGeneral Network Security Guidelines Setup Basic Setup Chapter Advanced ConfigurationHow to Access the Web-Based Utility Internet SetupStatic IP PPPoEOptional Settings Telstra CableRouter IP Network SetupDhcp Server Setting Dhcp ReservationDdns Service Setup DdnsTime Setting DynDNS.orgMAC Address Clone Setup MAC Address CloneSetup Advanced Routing Advanced RoutingRouting Table Wireless Basic Wireless SettingsBasic Wireless Settings Wireless Security Wireless Wireless SecurityWi-Fi Protected Setup WPA Enterprise WPA PersonalWPA2 Personal WPA2 EnterpriseRadius Access Restriction Wireless Wireless MAC FilterWireless MAC Filter MAC Address Filter ListAdvanced Wireless Wireless Client ListInternet Filter Security FirewallFirewall Web FilterVPN Passthrough Internet Access PolicySecurity VPN Passthrough SummaryApplications and Gaming Single Port Forwarding Port Range Forwarding Applications and Gaming Port Range ForwardingSingle Port Forwarding Port Range Triggering Applications & Gaming Port Range TriggeringApplications and Gaming DMZ Dhcp Client TableInternet Access Priority QoS Quality of ServiceWireless Applications and Gaming QoSMAC Address Administration ManagementOnline Games Ethernet PortAdministration Log ManagementLog Administration DiagnosticsDiagnostics Factory Defaults Administration Factory DefaultsAdministration Firmware Upgrade Upgrade FirmwareStatus Router Status Local NetworkStatus Wireless Network Wireless NetworkAppendix a Troubleshooting Your computer cannot connect to the InternetAppendix B Specifications EnvironmentalExclusions and Limitations Limited WarrantyObtaining Warranty Service Technical Support FCC Radiation Exposure Statement Safety NoticesFCC Statement Industry Canada StatementWireless Disclaimer Avis d’Industrie CanadaDansk Danish Miljøinformation for kunder i EU Regulatory Information Norsk Norwegian Miljøinformasjon for kunder i EU Regulatory Information Schedule 1 Linksys Software License Agreement Software in Linksys ProductsSoftware Licenses Schedule PreambleSoftware License Agreement Software License Agreement No Warranty OpenSSL License Original SSLeay License8041510B-DF