Cisco Systems 1400 manual 120 VAC, 15A U.S VAC, 10A International

Page 28

Chapter 2 Installation Overview

Warnings

Warnings

Translated versions of the following safety warnings are provided in Appendix A, “Translated Safety Warnings.”

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.”)

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.:NFPA 70, National Electrical Code, Article 810, in Canada: Canadian Electrical Code, Section 54).

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

120 VAC, 15A U.S. (240 VAC, 10A International)

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Warning Read the installation instructions before you connect the system to its power source.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.

Warning In order to comply with radio frequency (RF) exposure limits, the antennas for this product should be positioned no less than 6.56 ft (2 m) from your body or nearby persons.

Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03

2-2

OL-4072-04

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Corporate Headquarters Text Part Number OL-4072-04Cisco Systems, Inc. All rights reserved N T E N T S IiiStacking Bridges Using Ipsu to Set the Bridge’s IP Address and Ssid Overview D-2 Preface ObjectivesAudience OrganizationConventions ViiiRelated Publications Cisco.com Obtaining DocumentationProduct Documentation DVD Reporting Security Problems in Cisco Products Documentation FeedbackCisco Product Security Overview Ordering DocumentationProduct Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website XiiSubmitting a Service Request XiiiObtaining Additional Publications and Information Definitions of Service Request SeverityXiv Preface Obtaining Additional Publications and Information Xvi Overview Key Features Bridge ConfigurationsPower External AntennaEthernet Ports Integrated AntennaMetal Enclosure Bridge Connectors and LEDs Bridge LEDsReceive Signal Strength Indicator Port Network Configuration ExamplesPoint-to-Point Configuration Port Aggregation or Redundancy Configuration Point-to-Multipoint ConfigurationBridge Specifications Category Bridge Power Injector and Power ModuleCofdm Maximum Power Levels Installation Overview 120 VAC, 15A U.S VAC, 10A International FCC Safety Compliance Statement Safety InformationSafety Precautions Typical Bridge Installation Components Cables Ground See noteSite Surveys Installation GuidelinesUnpacking the Bridge Before Beginning the Installation Package ContentsBridge Layout and Connectors VDC power output cable AC power cord Power module Installation Summary Installation Overview Installation Summary Mounting and Alignment Overview Mounting Hardware Mounting the BridgeMulti-function Mount Bridge LEDs Mast Type Mast Diameter Mast Attachment MethodInstall LED State Bridge State LED and Connector LocationsAligning the Antenna Using LED Indications Signal Level dBm Ethernet LED Status LED Radio LEDAligning the Antenna Using the Rssi Voltage Rssi Reading voltsStacking Bridges Overview Installing the Stacked BridgesChoosing a Second Mounting Location Verifying Isolation Stacking Bridges Verifying Isolation Configuring the Bridge for the First Time Resetting the Bridge to Default Settings Before You StartConnecting to the Bridge Locally Obtaining and Assigning an IP AddressAssigning Basic Settings Summary Status OL-4072-04 Page Default Settings on the Express Setup Output Power LevelSetting Default What To Do NextProtecting Your Wireless LAN Using the IP Setup UtilityObtaining and Installing Ipsu Using Ipsu to Find the Bridge’s IP Address Click Get IP AddressUsing Ipsu to Set the Bridge’s IP Address and Ssid Ipsu Set Parameters ScreenUsing a Telnet Session to Access the CLI Assigning an IP Address Using the CLICommand Purpose Troubleshooting Checking the Bridge LEDs Bridge Normal Mode LED IndicationsEthernet Status Radio Meaning LED Blinking Codes First Second Power Injector LEDsDigit Description Power Injector LEDs Injector StatusChecking Power Checking Basic Configuration Settings Security SettingsUsing the Mode Button Resetting to the Default ConfigurationAntenna Alignment Using the Web Browser Interface Reloading the Bridge ImageWeb Browser Interface Browser Http InterfaceObtaining the Bridge Image File Browser Tftp InterfaceObtaining the Tftp Server Software Http//tftpd32.jounin.netTranslated Safety Warnings Appendix a Translated Safety Warnings Installation Warning Installation and Grounding Warning Page Circuit Breaker Warning Ground Conductor Warning OL-4072-04 Installation Warning Lightning Activity Warning Explosive Device Proximity Warning Radio Frequency Exposure LimitsEen dergelijk gebruik te voldoen Und bestimmtRestricted Area Warning Page OL-4072-04 Declarations of Conformity and Regulatory Information For Home or Office USE Industry Canada International ModelsCanadian Compliance Statement Cisco Part Number Model GainEuropean Community Ireland Declaration of Conformity for RF Exposure Administrative Rules for Cisco Aironet Bridges in Taiwan Chinese Translation English TranslationOperation of Cisco Aironet Bridges in Brazil Bridge ModelPortuguese Translation Channels and Maximum Power Levels OL-4072-04 Assembling the Rooftop or Wall Mount Package Contents Unpacking the MountAssembling the Mount Repeat Steps 8 and 9 for the other square holeOL-4072-04 O S S a R Y GL-1GL-2 GL-3 OfdmGL-4 Computing device with an installed client adapter GL-5GL-6 D E IN-1IN-2

1400 specifications

Cisco Systems 1400, known for its robust networking solutions, is a versatile and powerful device designed to enhance connectivity in various environments. The Cisco 1400 is part of the Cisco Industrial Router series and is tailored specifically for industrial applications, particularly in challenging environments where durability and reliability are paramount.

One of the main features of the Cisco 1400 is its rugged construction. It is built to withstand extreme temperatures, vibrations, and dust, making it ideal for deployment in factories, oil and gas rigs, and outdoor installations. This ruggedness ensures operational continuity in situations where standard networking equipment might fail.

Connectivity is another primary characteristic of the Cisco 1400. It supports a variety of WAN and LAN interfaces, including Serial, Ethernet, and cellular connections. This multifunctionality allows for flexible network design, enabling organizations to integrate the device into existing infrastructure seamlessly. Furthermore, it facilitates remote access, making it suitable for managing distributed networks in real-time.

The Cisco 1400 integrates advanced security features to safeguard data and network integrity. With support for VPN, firewall, and intrusion prevention systems, it provides a secure platform for critical communications. The device is also compliant with various industry standards and regulatory requirements, ensuring that organizations can maintain robust security postures in line with compliance mandates.

Another notable technology featured in the Cisco 1400 is its support for Cisco’s IoT capabilities. It can connect and manage numerous IoT devices, providing enhanced monitoring and data collection critical for industrial applications. This feature supports the concept of Industry 4.0, allowing businesses to leverage data analytics for predictive maintenance and operational efficiency.

Management and configuration of the Cisco 1400 are simplified through the use of Cisco Prime Infrastructure and Cisco DNA Center. These management tools provide intuitive dashboards and automated processes, streamlining network operations.

In summary, the Cisco Systems 1400 is a powerful, rugged networking solution designed for industrial applications. With its versatile connectivity options, robust security features, support for IoT technologies, and simplified management capabilities, it stands out as an exceptional choice for organizations looking to enhance their network infrastructure in challenging environments. This makes the Cisco 1400 an ideal solution for modern industrial connectivity needs.
Top Page Image Contents