Cabletron Systems 520, 510 manual By Cabletron Systems, Inc

Page 3

Notice

Only qualified personnel should perform installation procedures.

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

©1999 by Cabletron Systems, Inc.

All Rights Reserved. Printed in the United States of America.

Cabletron Systems, Inc.

35 Industrial Way

Rochester, NH 03867-0505

Order Number: 9032869 February 1999

Cabletron Systems and SPECTRUM are registered trademarks, and SmartSwitch is a trademark of Cabletron Systems, Inc.

IPX is a registered trademark of Novell, Inc.

DEC, DIGITAL, and the DIGITAL logo are trademarks of Compaq Computer Corporation.

All other trademarks and registered trademarks are the property of their respective holders.

i

Image 3

Contents

SmartSwitch Router 510 Installation and Configuration Guide Page By Cabletron Systems, Inc FCC Notice Cabletron SYSTEMS, INC. Program License Agreement Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Addendum Page Contents Chapter Connecting the Console Port Cable Chapter Configuring the RouterChapter Supporting Isdn for the SSR-510 Appendix a Problem Solving Appendix C Product SpecificationsAppendix D Installation Information United Kingdom Contents Using This Guide OverviewIntended Audience Chapter Title Description Appendix Structure of This GuidePart Number Title Description Related DocumentationHow to install and use the trace Document Conventions Term Definition GlossaryYour email address Getting HelpPage Product Introduction Chapter ContentsSSR-520 Router SSR-510 RouterFeatures Configuration and ManagementPerformance and Memory EasyStart Front and Back Panel Components Front Panel ComponentsIcon Name Description Refer to the Distributed Router Product Introduction Name Description Back Panel ComponentsBack Panel Layout Page Installing and Cabling Rack Mounting Shelf, Router and Power Supply Assembly Installing the Router in the Rack Mounting ShelfStep Action Assembling the Rack Mount ShelfAttaching Adhesive Strips Assembled Router and Rack Mount Shelf Cabling the SSR-510 Cabling the RoutersStep Action Cabling the SSR-520 Installing the SSR-520RouterStep Action Removing the SSR-510 Cables Removing the CablesRemoving the SSR-520 Cables Removing the SSR-520 CablesPage Connecting the Console Port Cable Console Port Device Cabling Signaling StandardsConnecting the Console Port Item Description Console Port Cabling ComponentsConfiguring the Router Using the Router Configurator to Configure the Router Step Action On the next Console ScreensConfiguring the Router Using the CLI to Manually Configure the Router Type 3 and press Return as shown in the following example EasyStart Stop Return To configure the router using Go to the section titledPreconfigured Router Screen Option Using Menus to Set up the RouterRestart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration IP ConfigurationSET Smnp READ/WRITE Community Set Snmp Read/Write CommunitySet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Enter yes to proceed. The following menu is then displayed Page Supporting Isdn for the SSR-510 Configuration Parameter Ordering Your Isdn LinePossible Values Obtaining a Network Termination Device Page Appendix Contents Problem SolvingEvent Description Normal PowerupThese tests are run prior to the router OK LED being lit Self-Test Progress StatesOption card dpram setup if present Off On Green Flashing Name LED DescriptionsLED Symptom Probable Cause Corrective Action Problem Solving Using the LEDsRouter 500 Series System Symptom Probable Cause Corrective Action Page Connectors, Adapters and Cable Connections Connector Assignments Pin Serial Port ConnectorPin Assignment DTR a Figure B-2 -pin MJ Connector 10BaseT Port 8-pin MJ ConnectorAdapters H8571-J AdapterH8575-A Adapter Cable Connections From Pin To X.21 Pin Signal Name Connector P1 Connector P2From Pin Connector To EIA422 Pin Signal Name Connector P2 Clock a From Pin Connector To V.35 Pin Signal Name Connector P2 From Pin Connector To EIA530A Pin Signal Name Connector P2 EIA530A Cable Connections BC12J-06 From Pin Connector To EIA423 Pin Signal Name Connector P2 19, 22, 25, 30 DTE Ground Speed Select 12, 29, 31, 34, 35 DTE Ground1 Speed Select Product Specifications Parameter Specification Product SpecificationsAcoustical Specifications ProductProdukt Connectors Quantity ConnectorsPart Part Number Parts ListPage Installation Information United Kingdom Service Categories Router Isolation Power Rating, Router Isolation and Safety StatusHost Power Rating Safety StatusInterface Cable Type Name Molding Pins Cable ApprovalSupported Cables Installation Information United Kingdom