Cabletron Systems 520, 510 manual Connecting the Console Port, Step Action

Page 45

Connecting the Console Port Cable

Connecting the Console Port

The console port connection is made through the console port on the router. To connect the console port on the SSR-510 or the SSR-520 routers, complete the following steps:

Step Action

1Ensure that the transmit and receive baud rates on the console port device are set to 9600 baud.

2Connect the console port device to the console port connector on the router.

The router’s console port is shown in Figure 3-1. The legend identifying the console port cabling follows the figure.

3-3

Image 45

Contents

SmartSwitch Router 510 Installation and Configuration Guide Page By Cabletron Systems, Inc FCC Notice Cabletron SYSTEMS, INC. Program License Agreement Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Addendum Page Contents Chapter Connecting the Console Port Cable Chapter Configuring the RouterChapter Supporting Isdn for the SSR-510 Appendix a Problem Solving Appendix C Product SpecificationsAppendix D Installation Information United Kingdom Contents Using This Guide OverviewIntended Audience Chapter Title Description Appendix Structure of This GuidePart Number Title Description Related DocumentationHow to install and use the trace Document Conventions Term Definition GlossaryYour email address Getting HelpPage Product Introduction Chapter ContentsSSR-520 Router SSR-510 RouterFeatures Configuration and ManagementPerformance and Memory EasyStart Front and Back Panel Components Front Panel ComponentsIcon Name Description Refer to the Distributed Router Product Introduction Name Description Back Panel ComponentsBack Panel Layout Page Installing and Cabling Rack Mounting Shelf, Router and Power Supply Assembly Installing the Router in the Rack Mounting ShelfStep Action Assembling the Rack Mount ShelfAttaching Adhesive Strips Assembled Router and Rack Mount Shelf Cabling the SSR-510 Cabling the RoutersStep Action Cabling the SSR-520 Installing the SSR-520RouterStep Action Removing the SSR-510 Cables Removing the Cables Removing the SSR-520 Cables Removing the SSR-520 CablesPage Connecting the Console Port Cable Console Port Device Cabling Signaling StandardsConnecting the Console Port Item Description Console Port Cabling ComponentsConfiguring the Router Using the Router Configurator to Configure the Router Step Action On the next Console ScreensConfiguring the Router Using the CLI to Manually Configure the Router Type 3 and press Return as shown in the following example EasyStart Stop Return To configure the router using Go to the section titledPreconfigured Router Screen Option Using Menus to Set up the RouterRestart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration IP ConfigurationSET Smnp READ/WRITE Community Set Snmp Read/Write CommunitySet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Enter yes to proceed. The following menu is then displayed Page Supporting Isdn for the SSR-510 Configuration Parameter Ordering Your Isdn LinePossible Values Obtaining a Network Termination Device Page Appendix Contents Problem SolvingEvent Description Normal PowerupThese tests are run prior to the router OK LED being lit Self-Test Progress StatesOption card dpram setup if present Off On Green Flashing Name LED DescriptionsLED Symptom Probable Cause Corrective Action Problem Solving Using the LEDsRouter 500 Series System Symptom Probable Cause Corrective Action Page Connectors, Adapters and Cable Connections Connector Assignments Pin Serial Port ConnectorPin Assignment DTR a Figure B-2 -pin MJ Connector 10BaseT Port 8-pin MJ ConnectorAdapters H8571-J AdapterH8575-A Adapter Cable Connections From Pin To X.21 Pin Signal Name Connector P1 Connector P2From Pin Connector To EIA422 Pin Signal Name Connector P2 Clock a From Pin Connector To V.35 Pin Signal Name Connector P2 From Pin Connector To EIA530A Pin Signal Name Connector P2 EIA530A Cable Connections BC12J-06 From Pin Connector To EIA423 Pin Signal Name Connector P2 19, 22, 25, 30 DTE Ground Speed Select 12, 29, 31, 34, 35 DTE Ground1 Speed Select Product Specifications Parameter Specification Product SpecificationsAcoustical Specifications ProductProdukt Connectors Quantity ConnectorsPart Part Number Parts ListPage Installation Information United Kingdom Service Categories Host Power Rating Power Rating, Router Isolation and Safety StatusSafety Status Router IsolationInterface Cable Type Name Molding Pins Cable ApprovalSupported Cables Installation Information United Kingdom