Cabletron Systems CSX200 manual Firmware Data Compression, Dhcp and NAT

Page 19

CSX200 Firmware Support

Firmware Data Compression

The STAC Electronics Stacker LZS Compression algorithm provides a minimum of 2:1 firmware data compression for the CSX200 over PPP and Frame Relay. Firmware data compression is supported in software on each WAN interface for line speeds of up to 256 Kbps per WPIM, which is equivalent to four DS0 channels. To use data compression, compatible equipment (which conforms to the applicable standards), must be in use at both ends of the WAN link. This method of data compression is used as the default, if the hardware compression module is not installed.

HDLC

High-level Data Link Control (HDLC) protocol is used in conjunction with the WPIM-HDSL to conserve WAN bandwidth between two compatible devices, over a point-to-point connection. The HDLC (RAW) protocol reduces the amount of overhead information that needs to be contained within each data packet to direct it to its destination. This decreased packet overhead provides more available bandwidth to transfer data.

DHCP and NAT

The Dynamic Host Configuration Protocol (DHCP) and Network Address Translation (NAT) schemes eliminate the expense of purchasing limited public IP addresses for each client on a local network, and the need to re-configure a client if it is moved to a different network.

The CSX200 acts as a DHCP server that lets individual clients (PCs, network equipment) take turns using a range of private IP addresses (often referred to as local IP addresses), and provides optional secondary setup features for these clients on a per-port basis. A private or “local” network is referred to as a sub network that is using private or “local” IP addresses. An “outside” network refers to a Wide Area Network (WAN) commonly known as an Internet. An Intranet is an “Internet” in use on a facility or campus where registered public IP addresses are required.

The CSX200 distributes these addresses on a first-come-first-served basis, dynamically assigning a local IP address to an individual client (from 253 available addresses). This local IP address is then “leased” for a predetermined amount of time, configured for a particular port. Each Ethernet port provides DHCP services for one Class C subnet and secondary setup features for individual clients that support the use of a default gateway, domain name and WINs server. On the Wide Area Network (WAN) side, the Network Address Translation (NAT) routing scheme lets clients with local IP addresses use the public IP address(es) of the CSX200 WAN interface(s) to access the WAN.

NAT lets several DHCP clients on a sub network connect to WAN clients by letting the DHCP clients share a single public IP address. The NAT scheme modifies the IP headers and addresses, and the selected fields in upper layer protocol headers.

CSX200 Installation Guide

2-5

Page 18 Page 20
Image 19
Page 18 Page 20
Contents CSX200 CyberSWITCH Installation Guide Page FCC Notice Vcci Notice Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Contents 10BASE-T LAN Requirements Appendix a Wpim Cable Specifications Index Related Documentation How to Use This GuideAppendix D, Glossary, defines commonly used networking terms Following conventions are used throughout this guide Document ConventionsYour email address Getting HelpWAN Connection CSX200 HardwareEthernet LAN Connection Remote Management Capabilities Optional FeaturesIeee 802.3 Ethernet CSX200 Firmware SupportWAN Protocols Dhcp and NAT Firmware Data CompressionFrame Relay Protocol PAP and Chap Security Point-to-Point Protocol PPPMultilink Protocol LQMBridging and Routing HdslAbout the CSX200 Bridging and Routing Protocol Filtering Simple Network Management Protocol Snmp System PasswordsLQM MIB RFC1989 PPP MP MIB RFC1990 About the CSX200 Software and Firmware Upgrades About the CSX200 CSX200 Installation Guide 10BASE-T Twisted Pair Network Network RequirementsEthernet Twisted Pair Ports Port Descriptions10BASE-T LAN Configuration Connecting UTP Cables to Ports 1 ThroughCable Pinouts RJ45 Crossover Cable Unpacking the CSX200 Installation GuidelinesRemoving the CSX200 Cover Removing the Plastic Chassis Cover Installing a WpimInstalling WPIMs COMP/ENCR Module Installation Tabletop and Shelf Installations Installing the CSX200Tabletop or Shelf Installation Rackmount InstallationCSX200 Rackmount Hardware Attaching the Strain-Relief BracketAttaching the Strain-Relief Bracket Attaching the Rackmount BracketsInstalling the CSX200 in a 19-Inch Rack Powering the CSX200Troubleshooting Troubleshooting Troubleshooting Troubleshooting the LAN Troubleshooting CSX200 HardwareStatus 1 STS1 LED is OFF Troubleshooting the WANLink LNK LED is RED Link LNK LED is AmberStatus 1 STS1 LED is RED Status 1 STS1 LED is Green Status 1 STS1 LED is AmberStatus 2 STS2 LED is OFF Status 2 STS 2 LED is RED WPIM-HDSL Installed in CSX200Status 2 STS2 LED is Green Status 2 STS2 LED is AmberUser Cannot Communicate with Remote Network Station Investigating Software Configuration ProblemsTest TST LED is Amber blinking Connection to Device Fails During Software ConfigurationInvestigating Software Configuration Problems Troubleshooting CSX200 Installation Guide Table A-1 T-1 Interface Cable Part Numbers Table A-2 T-1 Connector Pin AssignmentsTable A-4 Network Pin Assignments Table A-3 DTE Pin AssignmentsTable A-5 WPIM-SY Interface Cables WPIM-SYTable A-6 EIA-449 Interface EIA-449Table A-7 EIA-449 Interface Cable Pin Assignment Table A-9 V.35 Interface Cable Pin Assignment Table A-8 V.35 InterfaceDrain Table A-10 EIA-232 Interface EIA-232Table A-11 EIA-232 Interface Cable Pin Assignment Table A-13 X.21 Interface Cable Pin Assignment Table A-12 X.21 InterfaceEIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 a ALT a DCE Shield Drain Table A-17 Network Pinout Assignments Table A-16 DDS Interface Cable Part NumberTable A-19 Network Interface Table A-18 WPIM-E1 Connector InformationTable A-21 Network Interface Table A-20 DTE InterfaceTable A-23 WPIM-DI Network Table A-22 WPIM-DI Connector InformationTable A-25 WPIM-HDSL Network Interface Cable Pin Assignments Table A-24 WPIM-DI Drop and InsertPage Specifications and Standards Compliance Table B-1 Hardware SpecificationsIndividual Wpim Regulatory Compliance CSX200 Regulatory ComplianceWPIM-SY WPIM-E1 Table C-2 WPIM-DDS Only Table C-1 WPIM-DI and WPIM-T1Appendix C FCC Part 68 User’s Information for CSX200 FCC Part 68 User’s Information for CSX200 Agree to provide With proper documentation Glossary Appendix D Glossary Glossary Appendix D Glossary Glossary Appendix D Glossary Index Index
Related manuals
Manual 150 pages 59.82 Kb

CSX200 specifications

Cabletron Systems was a leading developer of networking solutions, and its CSX400 and CSX200 series of high-performance switches represent some of the key innovations in the field of enterprise networking during their time. Both models were geared towards enhancing network reliability, efficiency, and speed, particularly in environments where heavy data traffic and complex networking demands were prevalent.

The CSX400, designed for larger enterprises, boasts a robust architecture capable of handling significant throughput. One of its standout features is its stackable design, allowing multiple switches to be interconnected and managed seamlessly as a single unit. This scalability provides organizations with the flexibility to expand their networks without significant infrastructure overhauls. The CSX400 supports various Ethernet standards, including 10/100 Ethernet and Gigabit Ethernet, positioning it to effectively manage both legacy and modern networking requirements.

In addition to its scalability, the CSX400 is distinguished by its advanced Layer 2 and Layer 3 routing capabilities. This dual-layer functionality enables efficient data handling and is instrumental in managing traffic between different network segments. Moreover, the switch incorporates features like VLAN (Virtual Local Area Network) support and Quality of Service (QoS) prioritization, allowing for enhanced performance of critical applications and streamlined bandwidth allocation.

On the other hand, the CSX200 series is tailored for smaller enterprises or branch offices needing a reliable yet efficient networking solution. Despite its compact design, the CSX200 is equipped with essential features that promote effective network management and security. It offers a simplified management interface, making it user-friendly for network administrators. The switch also provides essential access control measures, employing technologies like IEEE 802.1X for network access security.

Both the CSX400 and CSX200 prioritize performance through the incorporation of advanced switching technologies. They support features such as Spanning Tree Protocol (STP), enabling loop-free topologies and enhanced network resilience. These attributes are particularly crucial in dynamic networking environments where downtime can have significant repercussions on business operations.

Overall, Cabletron Systems' CSX400 and CSX200 series represent a blend of scalability, advanced routing capabilities, and user-friendly management, making them vital assets for organizations looking to optimize their network infrastructure during a period of rapid technological evolution. With their rich feature sets and unwavering performance, these switches helped pave the way for modern networking solutions that cater to diverse enterprise needs.
Top Page Image Contents