Cabletron Systems CSX200 manual Bridging and Routing Protocol Filtering

Page 25

CSX200 Firmware Support

The CSX200 uses the Spanning Tree Algorithm to prevent data loops and duplicate data. This is a self-learning bridge, i.e., the bridge builds and updates an address table with each MAC source address and associated information when the packets are received.

IP Routing — IP routing support provides the ability to process TCP/IP frames at the network layer for routing. IP routing support includes the Routing Information Protocol (RIP) that allows the exchange of routing information on a TCP/IP network. The CSX200 receives and rebroadcasts RIP messages to and from adjacent routers and workstations.

IPX Routing — Internet Packet Exchange (IPX) routing support provides the ability to process Novell proprietary frames at the network layer for routing. IPX routing support includes both Routing Information Protocol (RIP), and Service Advertising Protocol (SAP). These protocols allow the exchange of routing information on a Novell NetWare network. The SAP protocol provides a means for routers and workstations to advertise their class of services (file, print, etc.) to adjacent routers and workstations.

Bridging and Routing Protocol Filtering

Filtering is used to allow efficient usage of network resources and provide security for your network and hosts.

IP Internet Firewall — The CSX200 supports IP Internet Firewall filtering to prevent unauthorized access to your system and network resources from the Internet or a corporate Intranet. Security can be configured to permit or deny IP traffic. The security is established by configuring IP access filters, which are based on source IP address, source mask, destination IP address, destination mask, protocol type, and application port identifiers for both Transmission Control Protocol (TCP) and User Datagram Protocol (UDP).

IP access filters allow individual IP source and destination pair filtering as well as IP address ranges and wild carding to match any IP address. Firewall filters can be defined to allow inbound only, outbound only, or bi-directional IP communication up to the UDP and TCP application port level. The CSX200 supports the IP Access Control (from the ctip-mib) Internet Firewall Filter.

Bridge Filtering — Bridge filtering lets a network administrator control the flow of packets across the CSX200. Bridge filtering is used to “deny” or “allow” packets based on a “matched pattern” using a specified position and hexadecimal content within the packet. This enables restricting or forwarding of messages based on address, protocol, or data content. Common uses include preventing access to remote networks, controlling unauthorized access to the local network, and limiting unnecessary traffic.

CSX200 Installation Guide

2-11

Image 25
Contents CSX200 CyberSWITCH Installation Guide Page FCC Notice Vcci Notice Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Contents 10BASE-T LAN Requirements Appendix a Wpim Cable Specifications Index Related Documentation How to Use This GuideAppendix D, Glossary, defines commonly used networking terms Following conventions are used throughout this guide Document ConventionsYour email address Getting HelpWAN Connection CSX200 HardwareEthernet LAN Connection Remote Management Capabilities Optional FeaturesIeee 802.3 Ethernet CSX200 Firmware SupportWAN Protocols Dhcp and NAT Firmware Data CompressionFrame Relay Protocol PAP and Chap Security Point-to-Point Protocol PPPMultilink Protocol LQMBridging and Routing HdslAbout the CSX200 Bridging and Routing Protocol Filtering Simple Network Management Protocol Snmp System PasswordsLQM MIB RFC1989 PPP MP MIB RFC1990 About the CSX200 Software and Firmware Upgrades About the CSX200 CSX200 Installation Guide 10BASE-T Twisted Pair Network Network RequirementsEthernet Twisted Pair Ports Port Descriptions10BASE-T LAN Configuration Connecting UTP Cables to Ports 1 ThroughCable Pinouts RJ45 Crossover Cable Unpacking the CSX200 Installation GuidelinesRemoving the CSX200 Cover Removing the Plastic Chassis Cover Installing a WpimInstalling WPIMs COMP/ENCR Module Installation Tabletop and Shelf Installations Installing the CSX200Tabletop or Shelf Installation Rackmount InstallationCSX200 Rackmount Hardware Attaching the Strain-Relief BracketAttaching the Strain-Relief Bracket Attaching the Rackmount BracketsInstalling the CSX200 in a 19-Inch Rack Powering the CSX200Troubleshooting Troubleshooting Troubleshooting Troubleshooting the LAN Troubleshooting CSX200 HardwareLink LNK LED is RED Troubleshooting the WANLink LNK LED is Amber Status 1 STS1 LED is OFFStatus 1 STS1 LED is RED Status 1 STS1 LED is Green Status 1 STS1 LED is AmberStatus 2 STS2 LED is OFF Status 2 STS 2 LED is RED WPIM-HDSL Installed in CSX200Status 2 STS2 LED is Green Status 2 STS2 LED is AmberTest TST LED is Amber blinking Investigating Software Configuration ProblemsConnection to Device Fails During Software Configuration User Cannot Communicate with Remote Network StationInvestigating Software Configuration Problems Troubleshooting CSX200 Installation Guide Table A-1 T-1 Interface Cable Part Numbers Table A-2 T-1 Connector Pin AssignmentsTable A-4 Network Pin Assignments Table A-3 DTE Pin AssignmentsTable A-5 WPIM-SY Interface Cables WPIM-SYTable A-6 EIA-449 Interface EIA-449Table A-7 EIA-449 Interface Cable Pin Assignment Table A-9 V.35 Interface Cable Pin Assignment Table A-8 V.35 InterfaceDrain Table A-10 EIA-232 Interface EIA-232Table A-11 EIA-232 Interface Cable Pin Assignment Table A-13 X.21 Interface Cable Pin Assignment Table A-12 X.21 InterfaceEIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 a ALT a DCE Shield Drain Table A-17 Network Pinout Assignments Table A-16 DDS Interface Cable Part NumberTable A-19 Network Interface Table A-18 WPIM-E1 Connector InformationTable A-21 Network Interface Table A-20 DTE InterfaceTable A-23 WPIM-DI Network Table A-22 WPIM-DI Connector InformationTable A-25 WPIM-HDSL Network Interface Cable Pin Assignments Table A-24 WPIM-DI Drop and InsertPage Specifications and Standards Compliance Table B-1 Hardware SpecificationsIndividual Wpim Regulatory Compliance CSX200 Regulatory ComplianceWPIM-SY WPIM-E1 Table C-2 WPIM-DDS Only Table C-1 WPIM-DI and WPIM-T1Appendix C FCC Part 68 User’s Information for CSX200 FCC Part 68 User’s Information for CSX200 Agree to provide With proper documentation Glossary Appendix D Glossary Glossary Appendix D Glossary Glossary Appendix D Glossary Index Index
Related manuals
Manual 150 pages 59.82 Kb

CSX200 specifications

Cabletron Systems was a leading developer of networking solutions, and its CSX400 and CSX200 series of high-performance switches represent some of the key innovations in the field of enterprise networking during their time. Both models were geared towards enhancing network reliability, efficiency, and speed, particularly in environments where heavy data traffic and complex networking demands were prevalent.

The CSX400, designed for larger enterprises, boasts a robust architecture capable of handling significant throughput. One of its standout features is its stackable design, allowing multiple switches to be interconnected and managed seamlessly as a single unit. This scalability provides organizations with the flexibility to expand their networks without significant infrastructure overhauls. The CSX400 supports various Ethernet standards, including 10/100 Ethernet and Gigabit Ethernet, positioning it to effectively manage both legacy and modern networking requirements.

In addition to its scalability, the CSX400 is distinguished by its advanced Layer 2 and Layer 3 routing capabilities. This dual-layer functionality enables efficient data handling and is instrumental in managing traffic between different network segments. Moreover, the switch incorporates features like VLAN (Virtual Local Area Network) support and Quality of Service (QoS) prioritization, allowing for enhanced performance of critical applications and streamlined bandwidth allocation.

On the other hand, the CSX200 series is tailored for smaller enterprises or branch offices needing a reliable yet efficient networking solution. Despite its compact design, the CSX200 is equipped with essential features that promote effective network management and security. It offers a simplified management interface, making it user-friendly for network administrators. The switch also provides essential access control measures, employing technologies like IEEE 802.1X for network access security.

Both the CSX400 and CSX200 prioritize performance through the incorporation of advanced switching technologies. They support features such as Spanning Tree Protocol (STP), enabling loop-free topologies and enhanced network resilience. These attributes are particularly crucial in dynamic networking environments where downtime can have significant repercussions on business operations.

Overall, Cabletron Systems' CSX400 and CSX200 series represent a blend of scalability, advanced routing capabilities, and user-friendly management, making them vital assets for organizations looking to optimize their network infrastructure during a period of rapid technological evolution. With their rich feature sets and unwavering performance, these switches helped pave the way for modern networking solutions that cater to diverse enterprise needs.