Cabletron Systems CSX200 manual COMP/ENCR Module Installation

Page 39

COMP/ENCR Module Installation

COMP/ENCR Module Installation

To install the CSX200-COMP/ENCR into the CSX200 chassis, perform the following procedure:

•Attach one end of the antistatic wrist strap to your wrist and the other end to an approved electrical ground.

•Unpack the CSX200-COMP/ENCR by carefully removing it from the shipping box and then from the protective plastic bag. Do not cut the bag as the device could be damaged. If there are any signs of damage, contact the Cabletron Systems Global Call Center. See the Getting Help section of this document.

The CSX200-COMP/ENCR comes with a pre-attached metal cage. Do not remove

!this cage.

CAUTION

•Remove all power from the CSX200.

•You must remove the chassis cover of the CSX200 to install the CSX200-COMP/ENCR (refer to Removing the CSX200 Cover on page 4-2).

•Locate the D-Type connector and the standoffs on the chassis (refer to Figure 4-3on the following page).

•The D-Type connector pins of the CSX200-COMP/ENCR only fit one way onto the CSX200 D-Type connector. Lower the CSX200-COMP/ENCR module onto the standoffs and align the connector with the connector pins. Carefully insert the connector pins of the CSX200-COMP/ENCR module into the CSX200 D-type connector.

•Press down firmly on the CSX200 COMP/ENCR module until the pins fit all the way into the connector.

•Secure the CSX200-COMP/ENCR with the standoff screws supplied with the CSX200-COMP/ENCR module.

•Replace the CSX200 chassis cover and reconnect power.

•The CSX200-COMP/ENCR installation is complete.

CSX200 Installation Guide

4-5

Page 38 Page 40
Image 39
Page 38 Page 40
Contents CSX200 CyberSWITCH Installation Guide Page FCC Notice Vcci Notice Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Contents 10BASE-T LAN Requirements Appendix a Wpim Cable Specifications Index Related Documentation How to Use This GuideAppendix D, Glossary, defines commonly used networking terms Following conventions are used throughout this guide Document ConventionsYour email address Getting HelpWAN Connection CSX200 HardwareEthernet LAN Connection Remote Management Capabilities Optional FeaturesCSX200 Firmware Support Ieee 802.3 EthernetWAN Protocols Dhcp and NAT Firmware Data CompressionFrame Relay Protocol PAP and Chap Security Point-to-Point Protocol PPPMultilink Protocol LQMBridging and Routing HdslAbout the CSX200 Bridging and Routing Protocol Filtering Simple Network Management Protocol Snmp System PasswordsLQM MIB RFC1989 PPP MP MIB RFC1990 About the CSX200 Software and Firmware Upgrades About the CSX200 CSX200 Installation Guide 10BASE-T Twisted Pair Network Network RequirementsEthernet Twisted Pair Ports Port Descriptions10BASE-T LAN Configuration Connecting UTP Cables to Ports 1 ThroughCable Pinouts RJ45 Crossover Cable Unpacking the CSX200 Installation GuidelinesRemoving the CSX200 Cover Removing the Plastic Chassis Cover Installing a WpimInstalling WPIMs COMP/ENCR Module Installation Tabletop and Shelf Installations Installing the CSX200Tabletop or Shelf Installation Rackmount InstallationCSX200 Rackmount Hardware Attaching the Strain-Relief BracketAttaching the Strain-Relief Bracket Attaching the Rackmount BracketsInstalling the CSX200 in a 19-Inch Rack Powering the CSX200Troubleshooting Troubleshooting Troubleshooting Troubleshooting the LAN Troubleshooting CSX200 HardwareStatus 1 STS1 LED is OFF Troubleshooting the WANLink LNK LED is RED Link LNK LED is AmberStatus 1 STS1 LED is RED Status 1 STS1 LED is Green Status 1 STS1 LED is AmberStatus 2 STS2 LED is OFF Status 2 STS 2 LED is RED WPIM-HDSL Installed in CSX200Status 2 STS2 LED is Green Status 2 STS2 LED is AmberUser Cannot Communicate with Remote Network Station Investigating Software Configuration ProblemsTest TST LED is Amber blinking Connection to Device Fails During Software ConfigurationInvestigating Software Configuration Problems Troubleshooting CSX200 Installation Guide Table A-1 T-1 Interface Cable Part Numbers Table A-2 T-1 Connector Pin AssignmentsTable A-4 Network Pin Assignments Table A-3 DTE Pin AssignmentsTable A-5 WPIM-SY Interface Cables WPIM-SYEIA-449 Table A-6 EIA-449 InterfaceTable A-7 EIA-449 Interface Cable Pin Assignment Table A-9 V.35 Interface Cable Pin Assignment Table A-8 V.35 InterfaceDrain EIA-232 Table A-10 EIA-232 InterfaceTable A-11 EIA-232 Interface Cable Pin Assignment Table A-13 X.21 Interface Cable Pin Assignment Table A-12 X.21 InterfaceEIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 a ALT a DCE Shield Drain Table A-17 Network Pinout Assignments Table A-16 DDS Interface Cable Part NumberTable A-19 Network Interface Table A-18 WPIM-E1 Connector InformationTable A-21 Network Interface Table A-20 DTE InterfaceTable A-23 WPIM-DI Network Table A-22 WPIM-DI Connector InformationTable A-25 WPIM-HDSL Network Interface Cable Pin Assignments Table A-24 WPIM-DI Drop and InsertPage Specifications and Standards Compliance Table B-1 Hardware SpecificationsIndividual Wpim Regulatory Compliance CSX200 Regulatory ComplianceWPIM-SY WPIM-E1 Table C-2 WPIM-DDS Only Table C-1 WPIM-DI and WPIM-T1Appendix C FCC Part 68 User’s Information for CSX200 FCC Part 68 User’s Information for CSX200 Agree to provide With proper documentation Glossary Appendix D Glossary Glossary Appendix D Glossary Glossary Appendix D Glossary Index Index
Related manuals
Manual 150 pages 59.82 Kb

CSX200 specifications

Cabletron Systems was a leading developer of networking solutions, and its CSX400 and CSX200 series of high-performance switches represent some of the key innovations in the field of enterprise networking during their time. Both models were geared towards enhancing network reliability, efficiency, and speed, particularly in environments where heavy data traffic and complex networking demands were prevalent.

The CSX400, designed for larger enterprises, boasts a robust architecture capable of handling significant throughput. One of its standout features is its stackable design, allowing multiple switches to be interconnected and managed seamlessly as a single unit. This scalability provides organizations with the flexibility to expand their networks without significant infrastructure overhauls. The CSX400 supports various Ethernet standards, including 10/100 Ethernet and Gigabit Ethernet, positioning it to effectively manage both legacy and modern networking requirements.

In addition to its scalability, the CSX400 is distinguished by its advanced Layer 2 and Layer 3 routing capabilities. This dual-layer functionality enables efficient data handling and is instrumental in managing traffic between different network segments. Moreover, the switch incorporates features like VLAN (Virtual Local Area Network) support and Quality of Service (QoS) prioritization, allowing for enhanced performance of critical applications and streamlined bandwidth allocation.

On the other hand, the CSX200 series is tailored for smaller enterprises or branch offices needing a reliable yet efficient networking solution. Despite its compact design, the CSX200 is equipped with essential features that promote effective network management and security. It offers a simplified management interface, making it user-friendly for network administrators. The switch also provides essential access control measures, employing technologies like IEEE 802.1X for network access security.

Both the CSX400 and CSX200 prioritize performance through the incorporation of advanced switching technologies. They support features such as Spanning Tree Protocol (STP), enabling loop-free topologies and enhanced network resilience. These attributes are particularly crucial in dynamic networking environments where downtime can have significant repercussions on business operations.

Overall, Cabletron Systems' CSX400 and CSX200 series represent a blend of scalability, advanced routing capabilities, and user-friendly management, making them vital assets for organizations looking to optimize their network infrastructure during a period of rapid technological evolution. With their rich feature sets and unwavering performance, these switches helped pave the way for modern networking solutions that cater to diverse enterprise needs.
Top Page Image Contents