Extron electronic DECORA TX/RX Apply Power to the USB Extenders, Connect the Host Transmitter

Page 2

Apply Power to the USB Extenders

1.Connect the external power supply to the receiver.

The power LED (A) on the receiver lights when power is applied.

2.Connect power to the transmitter depending upon the power source.

zz If using an external supply the power LED (A) of the transmitter lights when power is properly applied. The Link LED (B) on both the transmitter and receiver also lights to indicate proper link cable connection, or

zz If using a computer USB port to power the transmitter, the transmitter Power and Link LEDs do not light until after the laptop or PC is powered and booted up. The receiver Link LED lights once the transmitter is powered.

Connect the Host (Transmitter)

Transmitters

 

 

 

 

 

 

 

 

 

 

1. Connect a USB cable from the PC or laptop USB port to the

 

 

HOST

ACTIVITY

 

 

 

 

 

LINK HOST

transmitter Host port as shown on the previous page. The AAP and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Decora transmitters have a female mini USB Type B connector on the

 

 

 

 

 

USB EXTENDER AAP Tx

front panel for this connection.

 

 

 

 

 

 

a

 

 

 

b c

2. Reboot or power up the PC or laptop. The Host LED on the front

 

 

 

 

 

 

ACTIVITY

panel of the transmitter (C) lights when the PC recognizes the port.

 

 

LINK

HOST

 

 

 

 

 

 

If the PC is supplying transmitter power, the transmitter and receiver

 

 

 

 

 

USB Extender Tx

Link LEDs (B) both light.

a

b

c

 

Connect the Hub (Receiver)

Receivers

 

a

b c

USB Extender Tx D

1.Connect up to four USB cables from peripheral devices to the receiver Hub ports. The order of connection does not matter.

The Host LED on the receiver (C) lights as communications between the USB transmitter and host occur.

2.As each peripheral is connected, the LED for the appropriate hub port (D) lights when the PC has detected the device.

NOTE: The USB Extender receivers can supply up to 0.5 A to each connected peripheral.

HOST

NOTT

 

CAT 5/5e/6/7

POWE

TO

LINK

 

CONNECLAN

 

R

 

DO

 

up to 450' (135m)

 

R

 

 

1.0A

 

 

 

 

12V MAX

POWE

 

 

 

 

12V MAX

 

 

 

 

0.4A

 

 

 

 

Extron

USB

 

USB Extender TX

 

Twisted Pair Transmitter for USB Peripherals

 

HUB

 

ACTIVITY

c

1

3

HOST

LINK

b

2

4

1

3

 

 

 

 

 

 

2

4

 

 

 

USB EXTENDER AAP Rx

 

a

b c

d

 

 

ACTIVITY

 

 

 

LINK HOST

1

3

 

 

 

2

4

 

USB Extender Rx

Extron

USB Extender RX

Twisted Pair Receiver for USB Peripherals

 

 

HUB

 

 

3

 

 

4

 

 

1

 

NOTT

2

 

 

 

CONNECLAN

 

 

DO

 

 

TO

USB

LINK

 

USB Touchscreen

Display

a

d

b c

USB Extender Rx D

Extron

Annotator

Annotation Graphics

Processor

Projector/Display

 

Extron USA - West

Extron USA - East

Extron Europe

Extron Asia

Extron Japan

Extron China

Extron Middle East

 

 

Headquarters

 

 

 

 

 

 

 

 

+800.633.9876

+800.633.9876

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

+400.883.1568

+971.4.2991800

 

 

+81.3.3511.7656 FAX

+971.4.2991880 FAX

 

 

Inside USA/Canada Only

Inside USA/Canada Only

Inside Europe Only

Inside Asia Only

Inside China Only

 

 

 

 

 

 

+1.714.491.1500

+1.919.863.1794

+31.33.453.4040

+65.6383.4400

 

+86.21.3760.1568

 

 

 

+1.714.491.1517 FAX

+1.919.863.1797 FAX

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

+86.21.3760.1566 FAX

 

68-1719-50

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

Rev. D 09 11

© 2011 Extron Electronics All rights reserved.

www.extron.com

 

 

Image 2
Contents Mount the USB Extenders Run All CablesConnect the Hub Receiver Apply Power to the USB ExtendersConnect the Host Transmitter