Installation and Operation, cont’d
•Use the right two pins to increase the output signal and add 100% of the maximum peaking to the signal for very long cable runs.
1. | Insert the adapter plate screws through the holes in the |
| faceplate. Attach the adapter plates to the faceplate with |
| the provided captive washers and |
|
|
|
|
|
|
| Unity |
|
|
|
|
|
|
|
| 100% |
|
|
|
|
|
|
|
| 50% |
|
|
|
|
|
| s |
|
| |
|
| GRjust |
| per | Interface | 99 | ||
|
|
|
| REDJum |
| .A | 07 | |
|
|
| N |
| t |
| Rev |
|
| eak | EE men |
|
| ||||
| Ad |
|
| Series |
|
|
| |
| E |
|
|
|
|
|
| |
Gai | BLUing | 500 |
|
|
|
| ||
n/P |
|
|
|
|
|
|
| |
| RGB |
|
|
|
|
|
|
Red Adjustment (100% gain/peaking shown)
Green Adjustment (Unity shown) Blue Adjustment (50% gain/peaking shown)
| H. |
|
|
|
| SHIFT |
|
|
|
|
| LO | BU | |
|
| FF | ||
|
|
| CA ER | |
|
|
|
| L MO ED |
|
|
|
| NIT |
AUDIO | AUTO |
| OR | |
POWER |
|
| ||
|
|
|
| |
|
|
|
| I |
|
|
|
| NP |
|
|
|
| UT |
CS | PIN 9 |
|
|
|
|
|
|
| |
|
| ID | PIN | 11 |
|
| ID | ||
|
| PIN | ||
|
|
| 4 |
RG |
|
B 5 |
|
68 | W |
| ITH |
| AD |
| SP |
Adapter Plate
RGB 508
RGB 568
(up to 4 Plates)
Attaching audio output, power, and video output cables
Once the switches have been set, attach the cables that will be inaccessible after installation. These cables should already be installed in the wall, conduit or furniture. See pages
1. | Plug the wired audio connector into the audio output | |
| female connector on the bottom of the interface. | |
2. | Attach the video and sync output cables to the interface | |
| with BNC connectors. Pay close attention to the order and | |
| location of connectors. | |
|
| The connectors on the RGB 500 Series interfaces are |
|
| |
|
| arranged in the following order on the bottom of the |
|
| enclosure: B, G, R, H/HV, and V. |
3. | Attach the 12VDC to 24VDC power supply to the interface | |
| via the | |
| See pages | |
| power supply to the AC power outlet. The interface’s | |
| front panel power indicator LED will light. |
Attaching adapter plates
The RGB 508 and RGB 568 can have up to 4 optional adapter plates.
The adapter plates must be ordered separately. They also must be attached to the faceplate and cabled before the interface is installed in the wall or furniture. The screws needed for installing the adapter plates are built into the plates, so no additional screws will be needed.
Installing optional adapter plates
2. | Attach the output cables to the back side of the adapter |
| plate(s). Several adapter plates require conductors to be |
| soldered to the connectors. Attach foil and braided shields |
| to ground connections. |
RGB 500 Series • Installation and Operation |