Extron electronic ECP 1000 user manual Wipes, Standard wipe transitions

Page 10

Operation, cont’d

When the either title effect ends, the preview image disappears, and the program image is again intact.

To apply a title, do the following:

1.Press the Title button.

2.Press the screen selection buttons that correspond to the screens you want to switch. For example, if you want to apply the title to screen 2, press screen selection button 2. If you want to apply the title to screens 1 and 3, press screen selection buttons 1 and 3.

You can select a screen selection only if it is backlit.

3.If you want to use a duration other than the default duration, turn the Adjust knob until the desired duration appears on the LCD menu’s default screen.

4.Do one of the following.

•Press the Take button. During the time specified by the duration, the selected portion of the program image dissolves away to be replaced by the preview image. The Take button remains lit, and the Title button flashes.

When you want to end the title, press the Take button again.

•Move the T-bar control. The title appears and remains until you move the T-bar to the opposite end point of the t-bar slot. Or, you could stop moving the T-bar and press the Take button, in which case the title is completed during the remaining duration time.

Wipes

A wipe causes the preview image to replace the program image in any one of many directions.

•A standard wipe causes the preview image to appear to unroll over the program image horizontally or vertically. By default, the wipe has hard edges. The preview image can wipe across the program image with the following transitions (figure 3-8):

•From left to right

•From right to left

•From top to bottom

•From bottom to top

left to right

right to left

top to bottom

bottom to top

Figure 3-8 — Standard wipe transitions

•A curtain wipe causes the preview image to appear to unroll over the program image in two directions simultaneously. The preview image can wipe across the program image with the following transitions (figure 3-9):

•In from the left and right edges of the screen to the center of the screen

•Out from the center of the screen to the left and right edges of the screen

•In from the top and bottom of the screen to the center of the screen

•Out from the center of the screen to the top and bottom of the screen

Figure 3-9 — Curtain wipe effects

•A plus wipe causes the preview image to appear to unroll over the program image in one of two transitions (figure 3-10):

•Starting in all four corners of the screen and moving in to the center of the screen

•Starting in the center of the screen and moving out to the corners of the screen

Figure 3-10 — Plus wipe effects

•A square wipe causes the preview image to appear to unroll over the program image in one of two transitions (figure 3-11):

•Starting at all four edges of the screen and moving in to the center of the screen

•Starting in the center of the screen and moving out to the edges of the screen

3-8

ECP 1000 • Operation

ECP 1000 • Operation

3-9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents ECP Event Control PanelTable of Contents One Table of Contents, cont’dIntroduction Two InstallationFeatures Introductionroduction, cont’dInstallationtal ation, cont’d Rear Panel Features InstallationThree Installation, cont’dOperation Power-up Operationration, cont’d Top Panel ControlsOperation, cont’d Using the MenusPerforming a system reset Changing the backlight intensityApplying a cut Applying a SwitchApplying a dissolve Applying a titleWipes Standard wipe transitions11 Square wipe effects Four Control Software for WindowsControlSoftwareforforWindows,cont’d Installing the SoftwareStarting the Software Reference Information AAppendixControl Software for Windows, cont’d Cleaning the fan filter ReferencerenceInformation,cont’d Maintenance and UpgradesInstalling a firmware update Replacing keycap labels SpecificationsReference Information, cont’d GeneralPart Numbers MtbfPrecautions
Top Page Image Contents