Extron electronic ECP 1000 user manual ReferencerenceInformation,cont’d Maintenance and Upgrades

Page 15

ReferencerenceInformation,cont’d

Maintenance and Upgrades

You can perform the following maintenance operations and upgrades to the ECP 1000:

Cleaning the fan filter

Installing a firmware update

You can also replace the existing button labels if you have reprogrammed any of the effect buttons.

Cleaning the fan filter

The fan filter should be cleaned periodically, The frequency with which you need to clean the filter depends on the operating environment.

To clean the fan filter, do the following:

1.Remove the power cable from the ECP 1000 and from the power source.

Do not open the fan cover without first unplugging the power cord.

2.Using a small flat-blade screwdriver, pry the fan cover off of the rear panel of the ECP 1000 (figure A-1).

Fan

7.Attach the power cable to the ECP 1000 and to the power source. Make sure the ECP 1000 is working correctly.

Installing a firmware update

To install a firmware update, you may need to replace IC (integrated circuit) U9 or U11, or both. Replacing these ICs may result in loss of presets and other settings.

1.Remove the power cable from the ECP 1000 and from the power source.

Do not open the cover of the ECP 1000 without unplugging the power cord.

2.Remove 10 screws from the back, top, and front of the cover (figure A-2).

Lift Cover straight up.

Remove 10 screws

SCREEN

 

 

 

 

 

 

0

 

 

 

 

 

 

0

L

 

 

 

 

0

 

 

 

 

1

 

NE

 

 

P

 

 

PA

 

 

EC

 

OL

 

ST

 

NTR

 

 

 

 

CO

 

 

 

 

 

DJU

T

 

 

 

 

 

A

EN

 

 

 

 

 

 

 

EV

 

 

 

 

 

 

100-240V 50/60 Hz 0.5A

TO SGS

3

2

1

PROGRAM

Filter

Figure A-2 — Removing the cover

Filter Cover

Pry off Cover

3.Lift the cover from the ECP 1000 unit, and place it next to the unit.

Figure A-1 — Removing the fan filter

3.Lift the filter out of the fan filter enclosure.

4.Rinse the filter with water, and allow it to dry.

5.Replace the filter in the fan filter enclosure.

6.Press the fan filter cover back onto the rear panel of the ECP 1000. Make sure the left and right edges snap behind the shallow tabs on the sides of the fan filter enclosure.

Make sure you are electrically grounded before touching IC chips. Electrostatic discharge (EDS) can damage IC chips, even if you cannot sense the discharge.

4.Remove the 12 screws that attach the control board to the

bottom of the ECP 1000 (figure A-3).

A-2

ECP 1000 • Reference Information

ECP 1000 • Reference Information

A-3

Image 15
Contents Event Control Panel ECPTable of Contents Table of Contents, cont’d OneIntroduction Introductionroduction, cont’d InstallationFeatures TwoInstallation Installationtal ation, cont’d Rear Panel FeaturesInstallation, cont’d ThreeOperation Operationration, cont’d Top Panel Controls Power-upChanging the backlight intensity Using the MenusPerforming a system reset Operation, cont’dApplying a title Applying a SwitchApplying a dissolve Applying a cutStandard wipe transitions Wipes11 Square wipe effects Control Software for Windows FourInstalling the Software ControlSoftwareforforWindows,cont’dStarting the Software AAppendix Reference InformationControl Software for Windows, cont’d ReferencerenceInformation,cont’d Maintenance and Upgrades Cleaning the fan filterInstalling a firmware update General SpecificationsReference Information, cont’d Replacing keycap labelsMtbf Part NumbersPrecautions