Extron electronic JMP 9600 HD, JMP 9600 2K quick start Front Panel Controls and Indications

Page 3

JMP 9600 • Setup Guide

lDual Redundant AC Power Input connectors — Connect standard IEC power cords between one rear panel AC Power Input connector and a 100 to 240VAC, 50-60 Hz power source.

WARNING: Physically disconnect both power cables from the player before opening the case for servicing.

NOTE:

Although the unit performs reliably while running on a single AC power supply, doing so defeats the dual-

 

redundant power supply feature.

Connect the dual power cords to either uninterruptible power sources or to power sources that are completely

 

independent of each other.

mDual Redundant AC Power Input switches — Toggle both AC Power Input switches to the on ( ) position.

Front Panel Controls and Indications

nVideo LED — This LED blinks when the player is in Play mode or Pause mode.

14

15

 

 

16

VIDEO

 

DISK DRIVE

 

 

LAN

 

1

2

3

4

1

2

24

PREV

o Disk Drive 1 and 2 LEDs — These LEDs flash when the

 

 

 

 

 

ENTER

 

associated hard disk is active. When you are transferring a

 

 

 

 

 

 

 

large file or playing a high bit rate file the LEDs flash more

 

17

 

18

 

 

 

frequently. It is common, under heavy load, for the LEDs to

 

 

 

 

 

19

20

21

22

23

25

26

appear to be continuously lit.

NOTE: The Disk 3 and Disk 4 LEDs are reserved for possible future applications and are not currently implemented.

pLAN 1 and 2 LEDs — These LEDs flash when the associated Ethernet connection is active. When you are transferring a large file the LEDs flash more frequently. It is not uncommon, under heavy load, for the LEDs to appear to be continuously lit.

qPlay/Pause () button — Press this button to start the currently selected playlist or clip (DCP) file or pause a currently playing presentation while leaving the image displayed.

NOTE: Clips must conform to the Digital Cinema Initiative (DCI) DCP file format requirements (although encryption and watermarking are not currently supported). A clip is selected by choosing the associated *.cpl.xml file from the front

panel (see “Load and Play a Presentation”). Multiple DCP clips of the same format can be combined into playlists to

define their playback sequence, which can also be selected from the front panel.

rStop () button — Press this button to stop the currently playing presentation. When you press Play again, the presentation starts over from the beginning.

sPrevious clip () button — Press this button to load the previous clip in the playlist file. The button has no function if no playlist file has been loaded (using the menu controls).

tFrame mode button () — Press this button and then rotate the encoder knob (item z) to step frame-by-frame, backwards and forwards through the active clip while the player is in play mode.

uShuttle mode () button — Press this button and then rotate the encoder knob (item z) To “shuttle” backwards and forwards through the active clip, at a rate controlled by the encoder knob.

vNext clip () button — Press this button to load the next clip in the playlist file. The button has no function if no playlist file has been loaded (using the menu controls).

NOTE: The previous clip, frame, shuttle mode, and next clip features are not supported for 48 Fps clip files.

wLCD screen and confidence monitor — The LCD displays the user interface (the menu and submenu system shown in the drawing above) for local control. The screen can also display live output 1 or output 2 video. The alpha-blend feature allows you to display a mix of the user interface and output video simultaneously.

NOTE: Channel 2 Status is displayed in the main menu and available for selection only in 2-channel output mode and 2-channel locked output mode, both of which can be selected in the Settings > Video submenu.

x Previous button — Press this button to return to the previously displayed menu or page.

 

y Enter button — Press this button to initiate or activate a selected function.

 

z Encoder knob — Rotate this knob to navigate the menu system. Rotate this knob when frame mode and shuttle mode are

3

selected to operate those features.

 

Image 3
Contents Connections Lock Input and Output connectorsNetmask address LTC Input and Output connectorsLAN Both ports Gateway addressDisk Drive 1 and 2 LEDs These LEDs flash when Front Panel Controls and IndicationsSelect a clip Load and Play a Presentation