Extron electronic ISS 408 manual Installing a DVI Output Card

Page 92

4. Align the slots of each new firmware chip with the angled corners of the socket in the same orientation as the old chip. Gently, but firmly, press the chip into place in the socket.

5. Close the switcher. See “Opening and Closing the Switcher”, starting with step 9 on page 7-3.

Installing a DVI Output Card

You can install an optional digital visual interface (DVI) output card in the ISS. With the card installed, an additional program output is available as DVI video on a standard DVI connector. This program output is in addition to the standard RGB video on BNC connector and 15-pin HD connectors. Extron recommends that you send the unit to Extron for service and updates.

Install an optional DVI output card in the ISS as follows:

Changes to electronic components must be performed by authorized service personnel only.

To prevent electric shock, always unplug the ISS from the AC power source before opening the enclosure.

1. Open the switcher. See “Opening and Closing the Switcher” on page 7-2.

CAUTION

Do not touch any switches or other electronic components inside the ISS. Doing so could damage the ISS. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before proceeding with any electronic component replacement. A grounding wrist strap is recommended.

2. Locate the DVI output card connector opening on the rear panel and the DVI output card connector J14. When viewed from the front, connector J14 is in the far left corner of the main circuit board (figure 7-3).

DVI Output Card

Connector Opening

in ISS Rear Panel

DVI Output Card

Connector J14 on

Main Circuit Board

Figure 7-3 — DVI output card connector opening and socket J14

ISS 408 Integration Seamless Switcher • Maintenance and Modifications

7-5

Page 91 Page 93
Image 92
Page 91 Page 93
Contents ISS Precautions FCC Class B Notice Quick Start ISS Integration Seamless Switcher ISS 408 Integration Seamless Switcher Quick Start QS-1Quick Start ISS Integration Seamless Switcher, cont’d QS-2 ISS 408 Integration Seamless Switcher Quick StartTable of Contents Table of Contents, cont’d ISS 408 Integration Seamless Switcher Table of Contents Iii Iv ISS 408 Integration Seamless Switcher Table of Contents One About the Switcher ISS 408 Integration Seamless Switcher IntroductionIntroductiontroduction, cont’d About this ManualTypical ISS 408 Integration Seamless Switcher application Introduction, cont’d ISS 408 Integration Seamless Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Rack mountingMounting the switcher Mounting instructionsInput connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs videoOptional output connection Choosing a network cable Cabling and RJ-45 connector wiringWiring the network cable Configuration RS-232 connectionInstallation, cont’d Three Front Panel Controls and Indicators ISS 408 Integration Seamless Switcher OperationOperationeration, cont’d Black/Mute, input selection, and Cut/Dissolve controlsPicture adjustment and menu system controls InputsFront Panel Operations Power-on indicationsOperation, cont’d Selecting an input and switching it to the program output Press and release an input button figureCutting to the selected input Recalling a user preset Auto imaging an inputMenu system overview Extron Electronics ISS 60-423-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuISS 408 Integration Seamless Switcher Operation Advanced Configuration menu OffBlue-Only Mode and Edge Smoothing submenu RGB Delay submenuDissolve Speed submenu Test Pattern submenuEnhanced Mode submenu Pixel Phase submenuPreview Switch Mode submenu Auto Imaging and Auto Memories submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preview Preset submenuErase Preview Presets submenu Exit menuPicture adjustments 127 128 063 450 400 500 550Front panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Controls to position the imageGeneral checks TroubleshootingOptimizing the Audio Specific problems Problem Cause SolutionOperation, cont’d Four Ethernet Link ISS 408 Integration Seamless Switcher Programmer’s GuideRS-232 Link Ethernet connection SymbolsDefault address Switcher-Initiated Messages Power-upProgrammer’s Guide, cont’d Input selectionCutting or dissolving in swap mode Input and output video typeRGB delay and dissolve speed Preview switch mode PAL film modeAutomated adjustments Test patternUsing the Command/Response Table Host-to-Switcher InstructionsSwitcher Error Responses Command/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Horizontal detail filter RGB and component video inputs Vertical detail filter RGB and component video inputs Command/response table for SIS commands cont’d Information requests Command/response table for IP SIS commands Date and time entered should be Greenwich Mean Time GMTCommand/response table for special function SIS commands Command Ascii Command ResponseAuto Image Command/response table for advanced instruction set commands Command Hex Command ResponseFive Control Software for Windows Installing the softwareISS 408 Integration Seamless Switcher Switcher Software Ethernet protocol settings Software operation via EthernetSwitcher Software, cont’d Using the control programWindows Control program window Using the help program Button-Label GeneratorUsing the software To run the Button-Label Generator program, click StartSwitcher Software, cont’d Six Loading the Startup Control ISS 408 Integration Seamless Switcher Ethernet OperationEthernetOperation,cont’d Control ControlEthernet Operation, cont’d Selecting and switching an inputChanging the RGB delay or dissolve speed Using Blue-Only mode Blacking out the screen and muting the audioFreezing the output Outputting a test patternSystem Configuration Administration fieldsISS IP Settings fields ISS IP Address fieldISS Name field Hardware Address fieldFile Management File ManagementInput configuration SetupEthernet Operation, cont’d Output resolution Output rateOutput format Output polaritySeven Maintenance and Modifications Opening and Closing the SwitcherGrounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware UpgradeInstalling a DVI Output Card DVI output card connector opening and socket J14Output DVI board installation AAppendix a Cabling ISS 408 Integration Seamless Switcher Ethernet ConnectionEthernet Connection Pinging to determine Web IP address Determining Default AddressesPinging to determine the switcher’s IP address Connecting as a Telnet Client Ethernet Connection, cont’dTelnet tips OpenEscape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d ISS 408 Integration Seamless Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 104 pages 56.84 Kb

ISS 408 specifications

Extron Electronics is renowned for its contributions to the audiovisual industry, providing high-performance devices that meet the demands of professional environments. Two prominent products in their lineup are the ISS 108 and ISS 408 image scaling switchers, which are designed to enhance the management and quality of video signals in various applications.

The Extron ISS 108 is an 8x1 image scaling switcher that allows users to seamlessly switch between multiple video sources while ensuring high image quality. One of its main features is the ability to support a variety of video formats, including resolutions up to 4K. This versatility is crucial for applications in education, corporate settings, and events where different video sources may be required.

In terms of technology, the ISS 108 is equipped with advanced image scaling capabilities that improve the visual quality of the content being displayed. The device utilizes Extron's patented Vector 4K scaling technology, which enhances the clarity and detail of the images while maintaining the integrity of the source material. This technology is invaluable in environments where every detail matters, and it ensures that presentations are delivered at their best quality.

The ISS 408, on the other hand, takes the capabilities of the ISS 108 and elevates them further by offering 4x1 switching capabilities. This enables users to connect up to four video sources, giving them more flexibility in content management. The ISS 408 also supports 4K video resolutions, further solidifying Extron's commitment to delivering high-quality solutions.

Both models are designed with user-friendly interfaces, allowing for easy operation and integration into existing AV systems. They offer extensive control options, including RS-232 and Ethernet, enabling users to incorporate them into automation systems and control environments efficiently.

Another important characteristic of the ISS series is their built-in security features, such as password protection and lockout modes, which are essential for maintaining the integrity of sensitive content being delivered in corporate or educational settings.

In summary, the Extron ISS 108 and ISS 408 provide powerful solutions for image scaling and video switching. With advanced technologies like Vector 4K scaling, robust connectivity options, and intuitive control interfaces, these devices stand out as essential tools for any professional audiovisual application. Their focus on quality, flexibility, and security makes them ideal choices for enhancing video presentations in various environments.
Top Page Image Contents