Extron electronic RGB 202 Rxi user manual Mounting the Interfaces, Tabletop/desktop placement

Page 7

Instaltal lationandandOperation,cont’d

Installation and Operation Overview

This is an overview of the installation process. You will find detailed installation and operation instructions in this chapter.

To install and set up the RGB 202 Rxi and RGB 202 Rxi VTG interfaces, follow these basic steps:

1Turn all of the equipment (computers, remote controls, interface, projector/monitor, local monitor, and speakers or other audio device) off. Disconnect the power cords from the power source.

2Install the rubber feet for tabletop use, or install the appropriate brackets and furniture or rack mount the interface. See “Mounting the Interfaces” in this chapter.

3Attach the input (computers), output (display, local monitor and audio), and remote control cables. See “Cabling” in this chapter.

4Set the rear DIP switches. Use the “Rear Panel” section of this chapter as a guide.

5Connect power cords and turn on the devices: output devices (projector, monitors, speakers), remote control device, interface, and source computers.

6Select an input from the front panel toggle switch or the remote control (keypad, system, or PC).

7The image should now appear on screen, and sound should be audible. If not, ensure that all devices are plugged in and receiving power. Check the cabling and switch settings, and make adjustments as needed. Select a different input (or the VTG) to check for a picture and sound.

If problems persist, see “Troubleshooting” in this chapter, then call Extron’s customer support hotline, if needed.

8Adjust horizontal and vertical centering, and also level and peaking to obtain the best picture.

9For the RGB 202 Rxi VTG, set up and test the VTG. See “Operating the VTG” in this chapter.

Mounting the Interfaces

Select an installation option: tabletop/desktop placement, or under-desk, through-desk or rack mounting. Follow the appropriate installation guide on the next three pages.

2-2 RGB 202 Rxi, RGB 202 Rxi VTG • Installation and Operation

Tabletop/desktop placement

For tabletop or desktop placement only, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the interface enclosure.

Under-desk mounting

1.

Attach the optional under-desk mounting brackets

 

(part #70-077-01) to the interface with the six machine

 

screws (provided in the mounting kit), as shown below.

2.

Hold the interface with attached brackets against the

 

underside of the desk or other furniture. Mark the location

 

of holes for screws on the desk.

3.

Drill 1/4” (6.4 mm) deep, 3/32” (2.38 mm) diameter pilot

 

holes in the table or desk at the marked screw locations

 

from the underside/inside (concealed side) of the

 

furniture, where the interface will be located.

4.

Insert the four wood screws into the pilot holes. Fasten

 

each screw into the installation surface until just less than

 

1/4” of the screw protrudes.

5.

Align the installed screws with the slots in the mounting

 

brackets, and place the interface against the surface, with

 

the screws through the bracket slots.

6.

Slide the interface slightly forward or back, then tighten all

 

four screws to fasten it in place.

Under-desk mounting

RGB 202 Rxi, RGB 202 Rxi VTG • Installation and Operation

2-3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Universal Interfaces with Stereo Audio and Adsp User’s ManualPrecautions Table of Contents One Table of Contents, cont’dIntroduction About the RGB 202 Rxi and RGB 202 Rxi VTG FeaturesFeatures of both models Introductionroduction, cont’d About this ManualIntroduction, cont’d Installation and OperationAdditional RGB 202 Rxi VTG feature TwoMounting the Interfaces Tabletop/desktop placementRGB 202 Rxi, RGB 202 Rxi VTG Installation and Operation RGB 202 Rxi, RGB 202 Rxi VTG Installation and OperationThrough-desk mounting Installation and Operation, cont’dRack mounting Installation and Operation, cont’d Front Panel Rear Panel Interface/VTG selection switchDdsp Digital Display Sync Processing Cabling Pin SignalSOG sync on green For Rgbhv separate H and V sync output RGB 202 RScan rate indication Installation and Operation, cont’d LCD DisplayOperating the VTG RGB 202 Rxi VTG only LCD screen backlightIf the interface does not respond to controls Installation and Operation, cont’d TroubleshootingIf the image does not appear or there is no sound If the image is not displayed correctlyThree Remote ControlRS-232 Programmer’s Guide RemoteControl,cont’dUsing the software Remote Control, cont’dCommand/response table Installing the softwareRemote Control, cont’d Contact Closure Remote Control Specifications, Accessories Part NumbersAAppendix Video output Video signal characteristics RGB 202 Rxi VTG onlyVideo Video inputCables Specifications, cont’dOptional Accessories Included PartsLaptop breakout cables Part number Accessories and Part Numbers, cont’dRGB 202 Rxi, RGB 202 Rxi VTG Accessories and Part Numbers BNC cables Part number

RGB 202 Rxi, RGB 202 Rxi VTG specifications

The Extron RGB 202 Rxi VTG is a highly efficient, versatile video signal processor that offers robust functionality tailored for professional AV applications. This device is designed to handle RGB video and is particularly well-suited for integration into complex AV systems, providing exceptional image quality and ease of use.

One of the standout features of the RGB 202 Rxi is its ability to accommodate multiple video formats, including high-resolution RGBHV, RGBS, and even component video signals. This flexibility makes it an ideal choice for environments where varying sources need to be managed seamlessly. The device can output standard video formats up to 1920x1200, ensuring compatibility with a wide range of display technologies.

In addition to its impressive video handling capabilities, the RGB 202 Rxi incorporates advanced signal processing technologies. The built-in video scaling technology optimizes output resolutions, ensuring that images are displayed clearly and without distortion. This is especially important in environments where image detail is critical, such as in educational institutions, corporate settings, or command and control centers.

Another noteworthy characteristic of the RGB 202 Rxi is its extensive connectivity options. The device features multiple input and output connectors, including RGBHV, RS-232, and composite video, facilitating easy integration into existing systems. The integrated Electra™ technology enhances the unit's signal processing abilities, providing sharp and high-quality outputs regardless of the source material.

User-friendliness is also a key design element of the RGB 202 Rxi. Its intuitive front panel controls and LCD interface simplify operation, while the capability for remote control via RS-232 adds an extra layer of convenience for system operators. Additionally, with Extron’s software, operators can customize settings, manage presets, and monitor the device easily.

Overall, the Extron RGB 202 Rxi VTG represents a powerful solution for professional AV applications that require high-quality RGB video processing. Its combination of advanced technology, versatility, and user-friendly operation makes it a reliable choice for professionals who demand performance and flexibility in their AV systems. Whether in conference rooms or educational settings, this device is designed to meet the needs of dynamic and demanding environments.
Top Page Image Contents