Extron electronic PVS 204SA manual Reference Material, cont’d

Page 48

PRELIMINARY

Reference Material, cont’d

Audio output — power amplifier

Number/signal type

(1) stereo (default) or dual mono, 2 channels total

Connectors

(1) 5.0 mm captive screw connector, 4 pole

Impedance

4/8 ohms (single channel) or 4/8 ohms (stereo)

Amplifier type

Class D

Gain/volume adjustment

-10 dB to +10 dB (default = 0 dB), adjustable in 1 dB steps

Frequency response

20 Hz to 20 kHz, -1 dB/+3.5 dB @ 1 watt output, 8 ohm load

THD + Noise

0.2% @ 1 kHz at nominal level (1 watt, 8 ohm load)

S/N

>67 dB, 20 Hz to 20 kHz at maximum output (unweighted),

 

8 ohms (with 50’ cables)

Continuous power output with a full load at 1 kHz, 1% THD

At 4 ohms

13 watts (rms) per channel (1 watt tolerance)

At 8 ohms

7 watts (rms) per channel (1 watt tolerance)

Damping factor

>80 (8 ohm load)

Control/remote — switcher

Serial host control ports

2 bidirectional RS-232: 1 rear panel 3.5 mm captive screw connector,

 

5 pole (shared with IR control); 1 front panel 2.5 mm stereo mini jack

Baud rate and protocol

9600 baud, 8 data bits, 1 stop bit, no parity

Serial control pin configurations. Captive screw connector: A = TX, B = RX, C = IR receive, D = GND,

 

E = 12 VDC

 

2.5 mm mini stereo jack: tip = TX, ring = RX, sleeve = GND

DC volume control port

(1) 3.5 mm captive screw connector, 3 pole

DC volume control pin configurations

 

1 = 10 VDC, 2 = variable voltage or mute, 3 = GND

Volume control voltage range

0 V (mute) to 10 V (maximum volume)

Program control

Extron’s Simple Instruction Set (SIS)

General

External power supply

100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC,

 

3 A, regulated

Power input requirements

12 VDC, 3 A

Temperature/humidity

Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

 

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Rack mount

Yes, with optional 1U rack shelf, part #60-190-01 (RSU 129) or 60-604-01

 

(RSB 129); or 1U VersaTools® 3" deep rack shelf, part #60-190-20 (RSF 123) or

 

60-604-20 (RSB 123)

 

Also furniture mountable with an optional MBU 123 mini under-desk

 

mounting kit, part #70-212-01; or above-projector mountable with optional

 

kits PMK 350 (#70-563-xx) or PMK 300 (#70-374-01)

Enclosure type

Metal

Enclosure dimensions

1.7" H x 8.7" W x 3.0" D (1U high, half rack wide)

 

4.3 cm H x 22.1 cm W x 7.6 cm D

Product weight

2.5 lbs (1.1 kg)

Shipping weight

5 lbs (2.3 kg)

Vibration

ISTA 1A in carton (International Safe Transit Association)

Listings

UL, CUL

Compliances

CE, FCC Class A, VCCI, AS/NZS, ICES

MTBF

30,000 hours

Warranty

3 years parts and labor

NAll nominal levels are at ±10%.

NSpecifications are subject to change without notice.

A-4 PVS 204SA Switcher • Reference Material

Image 48
Contents PoleVault Switcher PVS 204SAPrecautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start PVS 204SA FCC Class a NoticeQuick Start PVS 204SA, cont’d Table of Contents Table of Contents, cont’d One PVS 204SA Switcher Introduction IntroductionAbout this Manual About the PVS 204SAFeatures Application Diagrams Introduction, cont’dMLP 101 AAP Introduction, cont’d Two Installation UL/Safety GuidelinesImportant safety instructions PVS 204SA Switcher InstallationMounting the Switcher Installing the PVS 204SA on the PMKRear Panel Features and Cabling Power connectionInput connections Twisted pair RGB video and audio cable wiring Installation, cont’d Output connectionsAux/Mix input connection As shown at rightRS-232/MLC/IR control port The PVS switcher can be Control connectionConfigured with a driver to 12 Connecting an IR Link to the switcher Speaker Configuration Speaker arrangement examplesConnecting speakers to the PVS 204SA Stereo or Dual Mono Output using parallel speaker wiringLabeling and connecting the A/V input cables Labeling the A/V InputsFinal Setup Labeling the PVT Decora face platesThree Operation and Setup Front Panel Features and OperationPVS 204SA Switcher Operation and Setup Setting Switcher Modes Single switcher modeSeparate switcher mode Setting the single switcher mode via the front panelAuto Switching Setting the separate switcher mode via the front panelSetting the input auto switching mode via the front panel Setting Up and Optimizing the Audio Steps for optimizing the audioFront panel input sensitivity adjustment Gain controlIndividual channel input sensitivity control Amplifier level controlResetting the Switcher Clipping indicatorBass, treble, and loudness control Aux/Mix controlFront Panel Security Lockout Executive Mode Setting the executive mode via the front panelFour Serial Communication RS-232 Programmer’s GuideHost-to-PVS communications PVS-initiated messagesError responses Using the command/response tablesSymbol definitions Factory defaults Serial Communication, cont’dCommand/response table for SIS commands Command Ascii Command Response Additional descriptionStatus commands Volume adjustmentCommand/response table for special function SIS commands Command Ascii Command Response ? valuesUpdating Firmware Click Upload to upload the firmware file into the PVS 204SA Preliminary Reference Material PVS 204SA Switcher Reference Material Reference MaterialVideo output composite video Reference Material, cont’d Part Numbers and Accessories AccessoriesIncluded parts Speaker accessories Cable accessoriesAccessory Part number Audio Block Diagram Reference MaterialAudio Reference Levels DBV Voltage DBuExtron’s Warranty Extron USA West