Extron electronic CTR 8 manual FCC Class a Notice, Registered Trademarks

Page 3

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference; the user must correct the interference at his own expense.

NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables must be used to ensure compliance with FCC emissions limits.

For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

Copyright

© 2013 Extron Electronics. All rights reserved.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of RGB Systems, Inc. or Extron Electronics:

Registered Trademarks (®)

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IP Intercom,

IP Link, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink, VLock, VersaTools, VNMatrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems

Registered Service Mark(SM) : S3 Service Support Solutions

Trademarks ()

AAP, AFL (AccuRate Frame Lock), ADSP (Advanced Digital Sync Processing), AutoImage, CDRS (Class D Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), ScopeTrigger, SIS, Simple Instruction Set, SkewFree, SpeedNav, TripleAction Switching, XTRA, ZipCaddy, ZipClip

Image 3
Contents CTR Sicherheitsanweisungen Deutsch Instrucciones de seguridad EspañolÈíñòðóêöèÿ ïî òåõíèêå áåçîïàñíîñòè Ðóññêèé FCC Class a Notice Registered TrademarksTrademarks Notifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideContents Features IntroductionAbout the CTR Panels Cabling Front Panel FeaturesRear Panel Features and Cabling Connectors see next= Ground pin Power ConnectionApplication with Show Me Cables Application DiagramsApplication with Individual Contact Closure Switch Application with CCR 4BLBSolder Cups CTR 8-Initiated Messages Using Simple Instruction Set SIS CommandsRemote Communication Control Host-to-CTR 8 CommunicationsSymbols Used in this Guide Error MessagesAscii to HEX Conversion Table Command and Response Table for SIS Commands MutingMute Modes LED Responses for Video Muting Button Input Button State Mute Mute mode Number ModeUpdating Firmware Downloading and Installing Firmware LoaderDownloading CTR 8 Firmware Installing Firmware with Firmware LoaderOpening Firmware Loader Add Next Select Edit Remove Selected Devices from the toolbar Under-desk and Furniture Mounting Tabletop PlacementMounting Rack MountingUSA, Canada, South America Japan Europe and Africa ChinaAsia Middle East